EchoStar HDS-600RS Mode d’emploi

DiSEqC™ Operation

HDS

600RS

Contents

1. Overview........................................................................................3

2. Changes to the Setup Wizard......................................................4

DiSEqC™ setup screen 1................................................................5

DiSEqC™ setup screen 2................................................................6

DiSEqC™ setup screen 3................................................................7

3. MANUAL CONFIGURATION ........................................................8

4 DiSEqC™ Configurations Supported........................................10

4.1 Symmetrical Setup...................................................................10

4.2 Single Tuner mode ...................................................................10

1. Overview

DiSEqC™ function has been added to the HDS600RS with firmware

release 121R and later. Operation of DiSEqC™ is designed for

experienced users only who have expert knowledge of multiple satellite

systems.

Whilst the product is predominantly a Freesat receiver it is possible to

manually tune to other satellites. Adding DiSEqC™ support allows

advanced users to configure the receiver to operate with DiSEqC™

switches used in multi-satellite dish systems.

The HDS-600RS is a dual tuner receiver and it is important to note that a

symmetrical system of DiSEqC™ switches must be used on LNB1 and

LNB2 inputs.

The firmware code for the HDS-600RS has been changed in the following

ways:

-Install wizard changed to add a new install path, to cater for basic

switch routing.

-A new setup screen has been added to view and change

configuration (off Settings->Tuner menu).

-When DiSEqC™ is enabled; a port per manual scan process has

been added to the manual scan process. This is for switching

satellites in non-Freesat mode. Only available (activated) when

DiSEqC™ is enabled.

-A DiSEqC™ mode option has been added to the HDS-600RS

The

default is disabled after a software download or factory reset.

-DiSEqC™ commands are only send on non-Freesat channels

-Cascading will not be supported.

-Dish steering will not be supported (This is only for DiSEqC™ 1.2).

2. Changes to the Setup Wizard

The Setup wizard has been changed to allow users of DiSEqC™

equipment to enable DiSEqC™ on the HDS-600RS. DiSEqC™ control can

also be enabled in the setup menu if not enabled in the Setup Wizard.

Please specify how your LNB is connected. If you are not sure, please

press the “OK” button.

-“OK” button: Direct connection to your Astra 28.2E LNB (per

standard setup)

-Yellow button: Astra 28.2E is connected via a DiSEqC™ Switch

setup

DiSEqC™ setup screen 1

Please enter the type of switch you are connected to.

•Green = Tone burst (Legacy)

•Yellow = DiSEqC™ 1.1 switch setup

•Red = Restarts wizard.

Note: before setting up the connection it is important to identify if the

DiSEqC™ switch used supports DiSEqC™ 1.0 or DiSEqC™ 1.1. Normally

this can be found on the switch frame.

DiSEqC™ setup screen 2

Allows the user to enter the number of input ports on the DiSEqC™

switches.

•Green = 2

•Yellow, = 3

•Blue, = 4

•Red = Restart Setup Wizard

DiSEqC™ setup screen 3

Allows the user to select the port to which the Freesat (Astra 28.2E) dish is

connected.

•Red, = 1

•Green, = 2

•Yellow, = 3

•Blue = 4

After this stage, the HDS-600RS will check for the home transponder on

both inputs. When this completes, the use is given on one of two options

•Existing scan screen

•Existing signal error screen

Note: If the home transponder cannot be seen on tuner 2, the usual

warning screen will be displayed.

3. MANUAL CONFIGURATION

The DiSEqC™ menus can be used to configure the DiSEqC™ settings

when an existing Freesat system is expanded to include multiple satellite

dishes. These follow a similar confirmation sequence to that described in

the Wizard setup.

To enter the DiSEqC™ setup screen press the Main Menu key on the

remote & then select: Settings/Tuning/DiSEqC™

It is essential that the Freesat dish (28.2 E) is configured correctly

otherwise normal operation of Freesat services will be affected.

3.1 TUNING of NON-FREESAT CHANNELS

Tuning of services on non-Freesat satellites is carried out as follows

Enter the Manual Tune screen by pressing the Main Menu key on the

remote & then select: Settings/Tuning

The following screen will be displayed:

Select Manual Scan to display the following screen:

Select the appropriate parameters to correspond to the physical DiSEqC™

switch configuration and desired Satellite services.

Select the Scan option, followed by “Start Scan” to tune to the desired

programmes. Programmes will be stored from Channel 5000 upwards.

Press the Back key & then select

Viewing Mode/Non Freesat

Press Exit to return to normal viewing of non-Freesat channels

4 DiSEqC™ Configurations Supported

4.1 Symmetrical Setup

A symmetrical configuration (dual switches) is assumed, with 2-4 input

ports per switch. After installing in dual tuner mode, both tuners are

available to Freesat services for dual record, or for non-Freesat mode.

4.2 Single Tuner mode

This is not supported for DiSEqC™ mode.

Legacy / 1.1 Switch

Port

Astra 28.2E

DVB FTA Sat A

Astra

28.2E

DVB FTA Sat A

HDS600RS

Tuner 1

Legacy / 1.1 Switch

Port

www.myechostar.com

Visit Us

Dolby and the double

D symbol are registered trademarks of Dolby laboratories.

HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks

or registered trademarks of HDMI Licensing LLC.

The DiSEqC™ standard & software and the DiSEqC™logos are copyright of and registered trademarks of Eutelsat S.A.

Sling Media, SlingLoaded and SlingPlayer are the registered or unregistered trademarks of Sling Media, Inc.

All other brand and product names are or may be trademarks of, and are used to identify products or services of, their

respective owners.

EchoStar Europe, Beckside Design Centre, Millennium Business Park,

Station Road, Steeton, Keighley, West Yorkshire BD20 6QW.

Autres manuels pour HDS-600RS

Table des matières

Autres manuels EchoStar Récepteur

EchoStar

EchoStar DSB-2200 2Ci Viaccess Manuel utilisateur

EchoStar

EchoStar DSB-880 2Ci Manuel utilisateur

EchoStar

EchoStar DSB-1100 Manuel utilisateur

EchoStar

EchoStar T-101 FTA Manuel utilisateur

EchoStar

EchoStar DSB-700 FTA Manuel utilisateur

EchoStar

EchoStar DVR-5000 HDD Viaccess Manuel utilisateur

EchoStar

EchoStar D-2400 IP Manuel utilisateur

EchoStar

EchoStar T-105 Manuel utilisateur

EchoStar

EchoStar DSB-707 FTA Manuel utilisateur

EchoStar

EchoStar DVR-5000 HDD Viaccess Manuel utilisateur

EchoStar

EchoStar DSB-2200 2Ci Viaccess Manuel utilisateur

EchoStar

EchoStar T-232 FTA Manuel utilisateur

EchoStar

EchoStar DVR-7000 HDD Viaccess Manuel utilisateur

EchoStar

EchoStar T-222 FTA Manuel utilisateur

EchoStar

EchoStar DSB-800 2Ci Manuel utilisateur

EchoStar

EchoStar DSB-1220 FTA Manuel utilisateur

EchoStar

EchoStar DSB-770 FTA Manuel utilisateur

EchoStar

EchoStar DSB-808 2Ci Viaccess Manuel utilisateur

EchoStar

EchoStar DVR-5000 HDD Viaccess Manuel

EchoStar

EchoStar DSB-890 2Ci Manuel utilisateur

EchoStar

EchoStar AD-3600 IP Viaccess Manuel utilisateur

EchoStar

EchoStar T-101 FTA Guide de dépannage

EchoStar

EchoStar DSB-2220 2Ci Manuel utilisateur

EchoStar

EchoStar D-2510 IP Viaccess Manuel utilisateur

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur