Eaton Tower 6KS Manuel utilisateur

Eaton 9E-IN User Manual

Tower 6-10K

Service and support:

Call your local service representative

SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS. This manual contains important instructions that

should be followed during installation and maintenance of the UPS and

batteries.

The UPS models that are covered in this manual are intended for installation in

an environment within 0 to 50°C, free of conductive contaminant.

Certification standards

•

Safety: EN 62040-1

•

EMC: IEC/EN 62040-2

•

IEC 61000-4-2 (ESD): level 3.

•

IEC 61000-4-3 (Radiated field): level 3.

•

IEC 61000-4-4 (EFT): level 4.

•

IEC 61000-4-5 (Fast transients): level 4.

•

IEC 61000-4-6 (Electromagnetic field): level 3.

•

IEC 61000-4-8 (Conducted magnetic field): level 4.

•

Performance: IEC/EN 62040-3

Special symbols

The following are examples of symbols used on the UPS or accessories to alert you

to important information:

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric

shock symbol.

Important instructions that must always be followed.

Do not discard the UPS or the UPS batteries in the trash.

This product contains sealed lead acid batteries and must be disposed as it's explain

in this manual. For more information, contact your local recycling/reuse or

hazardous waste center.

This symbol indicates that you should not discard waste electrical or electronic

equipment (WEEE) in the trash. For proper disposal, contact your local

recycling/reuse or hazardous waste center.

Information, advice, help.

Refer to the user manual.

Safety of persons

 RISK OF VOLTAGE BACKFEED. The system has its own power source (the

battery). Isolate the UPS and check for hazardous voltage upstream and

downstream during lockout-tagout operation. Terminal blocks may be

energized even if the system is disconnected from the AC power source.

 Dangerous voltage levels are present within the system. It should be opened

exclusively by qualified service personnel.

 The system must be properly grounded.

 The battery supplied with the system contains small amounts of toxic

materials. To avoid accidents, the directives listed below must be observed:

- Servicing of batteries should be performed or supervised by personnel

knowledgeable about batteries and the required precautions.

- When replacing batteries, replace with the same type and number of

batteries or battery packs.

- Do not dispose of batteries in a fire. The batteries may explode.

- Batteries constitute a danger (electrical shock, burns). The short-circuit

current may be very high.

 Precautions must be taken for all handling:

- Wear rubber gloves and boots.

- Do not lay tools or metal parts on top of batteries.

- Disconnect charging source prior to connecting or disconnecting battery

terminals.

- Determine if battery is inadvertently grounded. If inadvertently grounded,

remove source from ground. Contact with any part of a grounded battery

can result in electrical shock. The likelihood of such shock can be reduced if

such grounds are removed during installation and maintenance (applicable

to equipment and remote battery supplies not having a grounded supply

circuit).

Product safety

 The UPS connection instructions and operation described in the manual must

be followed in the indicated order.

 CAUTION - To reduce the risk of fire, the unit connects only to a circuit

provided with branch circuit overcurrent protection for :

63A rating, for 6kVA models,

100A rating, for 10kVA models

The upstream circuit breaker for Normal AC/Bypass AC must be easily

accessible. The unit can be disconnected from AC power source by opening this

circuit breaker.

 An additional AC contactor is used for backfeed protection and must comply

with IEC/EN 62040-1 (the creep age and clearance distances shall meet the

basic insulation requirements for pollution degree 2).

 Disconnection and overcurrent protection devices shall be provided by others

for permanently connected AC input (Normal AC/Bypass AC) and AC output

circuits.

 Check that the indications on the rating plate correspond to your AC powered

system and to the actual electrical consumption of all the equipment to be

connected to the system.

 For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the

equipment and shall be easily accessible

 Never install the system near liquids or in an excessively damp environment.

 Never let a foreign body penetrate inside the system.

 Never block the ventilation grates of the system.

 Never expose the system to direct sunlight or source of heat.

 If the system must be stored prior to installation, storage must be in a dry

place.

 The admissible storage temperature range is -25°C to +60°C with battery(-15°C

to +40°C without battery).

Special precautions

 The unit is heavy: wear safety shoes and use vacuum lifter preferentially for

handling operations.

 All handling operations will require at least two people (unpacking, lifting,

installation in rack system).

 Straps are provided only for unpacking manually the unit from the carton;

don’t use the straps to carry the unit around. The unit can slip from the straps

during handling (risk of injury and product damage):

- keep 12in / 30cm minimum distance between the straps

- lift the unit carefully and keep it at low height

- keep the unit horizontal during unpacking.

 Before and after the installation, if the UPS remains de-energized for a long

period, the UPS must be energized for a period of 24 hours, at least once every

6 months (for a normal storage temperature less than 25°C). This charges the

battery, thus avoiding possible irreversible damage.

 During the replacement of the Battery Module, it is imperative to use the same

type and number of element as the original Battery Module provided with the

UPS to maintain an identical level of performance and safety.

Contents

1. INTRODUCTION ............................................................................................ 1

1.1 ENVIRONMENTAL PROTECTION ............................................................................... 1

2. PRESENTATION ............................................................................................. 3

2.1 FRONT PANEL ...................................................................................................... 3

2.2 REAR PANELS ...................................................................................................... 4

2.3 CIRCUIT DIAGRAM ............................................................................................... 5

3. INSTALLATION ............................................................................................... 6

3.1 INSPECTING THE EQUIPMENT ................................................................................. 6

3.2 UNPACKING THE UNIT .......................................................................................... 6

3.3 CHECKING THE ACCESSORY KIT ................................................................................ 8

3.4 INSTALL THE UNIT ................................................................................................ 8

4. POWER CABLES CONNECTION .................................................................... 10

4.1 ACCESS TO TERMINAL BLOCKS (AC SOURCE TO UPS) ................................................ 11

4.3 PARALLEL INSTALLATION AND OPERATION (OPTIONAL) .............................................. 12

5. OPERATION ................................................................................................ 16

5.1 CONTROL PANEL ................................................................................................ 16

5.2 LCD DESCRIPTION.............................................................................................. 18

5.3 DISPLAY FUNCTIONS ........................................................................................... 21

5.4 USER SETTINGS ................................................................................................. 21

5.5 UPS STARTUP AND SHUTDOWN ............................................................................ 22

5.6 LCD OPERATION ................................................................................................ 24

6. COMMUNICATION ...................................................................................... 32

6.1 COMMUNICATION PORTS .................................................................................... 32

6.2 INTELLIGENT CARD (OPTIONAL)............................................................................ 33

6.3 UPS MANAGEMENT SOFTWARE ........................................................................... 33

7. UPS MAINTENANCE .................................................................................... 34

7.1 EQUIPMENT CARE .............................................................................................. 34

7.2 TRANSPORTING THE UPS .................................................................................... 34

7.3 STORING THE EQUIPMENT ................................................................................... 34

7.4 REPLACING BATTERIES ........................................................................................ 35

7.5RECYCLING THE USED EQUIPMENT.......................................................................... 36

8. TROUBLESHOOTING ................................................................................... 37

8.1 TYPICAL ALARMS AND FAULTS ............................................................................... 37

8.2 SILENCING THE ALARM ........................................................................................ 41

9. SPECIFICATIONS .......................................................................................... 42

9.1 MODEL SPECIFICATIONS ...................................................................................... 42

10 GLOSSARY .................................................................................................. 47

1. Introduction

Thank you for selecting UPS to protect your electrical equipment. The UPS has

been designed with the utmost care.

We recommend that you take the time to read this manual to take full

advantage of the many features of your UPS (Uninterruptible Power System).

Before installing your UPS, please read the booklet presenting the safety

instructions. Then follow the indications in this manual.

1.1 Environmental protection

Products are developed according to an eco-design approach.

Substances

This product does not contain CFCs, HCFCs or asbestos.

Packing

To improve waste treatment and facilitate recycling, separate the various

packing components.

•

The cardboard we use comprises over 50% of recycled cardboard.

•

Sacks and bags are made of polyethylene.

•

Packing materials are recyclable and bear the appropriate identification

symbol

Materials

Abbreviations

Number in

the symbols

Polyethylene terephthalat

PET

High-density polyethylene

HDPE 02

Polyvinyl chloride

PVC 03

Low-density polyethylene

LDPE 04

Polypropylene

PP 05

Polystyrene

PS 06

Follow all local regulations for the disposal of packing materials.

Product

The product is made up of recyclable materials.

Dismantling and destruction must take place in compliance with all local

regulations concerning waste. At the end of its service life, the product must be

transported to a processing center for electrical and electronic waste.

Battery

The product contains lead-acid batteries that must be processed according to

applicable local regulations concerning batteries.

The battery may be removed to comply with regulations and in view of correct

disposal.

1.2 Electronic equipment protection

The uninterruptible power system (UPS) protects your sensitive electronic

equipment from the most common power problems, including power failures,

power sags, power surges, brownouts, line noise, high voltage spikes,

frequency variations, switching transients, and harmonic distortion.

Power outages may occur unexpected, and the power quality will be erratic.

These power problems have the potential to corrupt critical data, destroy

unsaved work sessions, and damage hardware - causing hours of lost

productivity and expensive repairs.

With the UPS, you can safely eliminate the effects of power disturbances and

guard the integrity of your equipment. Providing outstanding performance and

reliability, UPS’s unique benefits include:

 True online double-conversion technology with high power density, utility

frequency independence, and generator compatibility.

 Selectable High Efficiency mode of operation.

 Standard communication options: one RS232 communication port, one

USB communication port, one dry in port and dry out port.

 Optional connectivity cards with enhanced communication capabilities.

 Firmware that is easily upgradable without a service call.

2. Presentation

2.1 Front panel

Tower model:

Tower UPS 6KS/10KS Tower UPS 6K/10K Tower EBM

2.2 Rear panels

Tower model:

Tower UPS 6KS Tower UPS 10KS

Tower UPS 6K Tower UPS 10K Tower EBM

1. Intelligent slot

2. USB

3. RS232

4. RJ11 (only for RT model)

5. EPO

6. Parallel card (optional)

7. Dry IN/OUT

8. Input /Output terminal

(Standard model 5pole, IPL, IPN, PE,

OPL, OPN; long backup model has 2

version, one is 5 Pole. Another is 7pole.

7pole add bat+, bat-, and no external

battery connector #10.)

9. Input switch

10. External battery connector

11. Maintenance bypass switch (optional)

12. EBM connector

13. EBM connector

14. Fuse board cover (replace EBM fuse)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Eaton UPS

Eaton

Eaton EX 2200 RT 3U Manuel utilisateur

Eaton

Eaton Eaton 5PX Instructions de montage

Eaton

Eaton Powerware 9355 Manuel utilisateur

Eaton

Eaton 9130 UPS Manuel utilisateur

Eaton

Eaton 93PM IBC-LW Manuel utilisateur

Eaton

Eaton E.T.N 1500 VA - 60kVa Manuel utilisateur

Eaton

Eaton Powerware 9910-E64 Manuel utilisateur

Eaton

Eaton Ellipse MAX 600 Pulsar Series Manuel utilisateur

Eaton

Eaton 9PX5KP1 Instructions d'installation et d'utilisation

Eaton

Eaton Power Xpert Plus 1 Manuel utilisateur

Eaton

Eaton 9125 Two-in-One UPS 2500 Manuel utilisateur

Eaton

Eaton 5P 1150VA RM Manuel utilisateur

Eaton

Eaton Protection Station 650 Manuel utilisateur

Eaton

Eaton MX Frame 15000 RT Manuel utilisateur

Eaton

Eaton Powerware 5110 Manuel utilisateur

Eaton

Eaton 9395-275 Manuel

Eaton

Eaton 93PM-50-1 Manuel utilisateur

Eaton

Eaton 500 Manuel utilisateur

Eaton

Eaton Power Xpert 9395P Manuel utilisateur

Eaton

Eaton 5E Manuel utilisateur

Eaton

Eaton Power Xpert 9395P-600/600 Manuel utilisateur

Eaton

Eaton Powerware 9130 Manuel utilisateur

Eaton

Eaton Tripp Lite SmartOnline Series Manuel utilisateur

Eaton

Eaton 9395 UPS and Plus 1 UPS 650825 kVA Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur

ZincFive

ZincFive BC Series Manuel utilisateur