Eaton Power Xpert Manuel de programmation

p/n: 164950240

Revision 04

Power Xpert Gateway

PXGX UPS

EMP Upstream Downstream

100100 Act Act Setup

Restart

Status

DHCP

Ident

Power

Package Contents

lPower Xpert Gateway Minislot (PXGX) UPS Card

lUSB Cable

lQuick Start Instructions

Quick Start Instructions

Eaton®® Power Xpert®® Gateway (PXGX) UPS Card

Eaton reserves the right to change specifications without prior notice Eaton®, Power Xpert®, and PredictPulseTM are registered

trademarks of Eaton or its subsidiaries and affiliates Google Chrome is a trademark of Google Inc Linux is a registered trademark of

Linus Torvalds Microsoft, Internet Explorer, and Windows are registered trademarks of Microsoft Corporation in the United States and in

other countries Mozilla and Firefox are registered trademarks of the Mozilla Foundation other trademarks are property of their respective

companies All other trademarks are property of their respective companies All other trademarks are property of their respective

companies

express written approval of Eaton

HHeellpp DDeesskk NNuummbbeerrss

United States 1-800-356-5737 or 1-800-843-9433

Canada 1-800-461-9166 ext 260

All Other Countries Call your local service representative

Web Site www.eaton.com/pxgx

NOTE On the Web site opening page, click Support and select the Customer Service

link for more information.

Eaton Power Xpert® Gateway PXGX UPS Card Quick Start Instructions 164950240—Rev 04 iii

TTaabbllee ooff CCoonntteennttss

EEaattoonn PPoowweerr XXppeerrtt GGaatteewwaayy ((PPXXGGXX)) UUPPSS CCaarrdd QQuu cckk SSttaarrtt IInnssttrruucctt oonnss................................................................................................................................11

Installation Checklist ........................................................................................................................................1

Install the Card................................................................................................................................................2

Connect the Card to the Computer ...................................................................................................................... 3

Install the Driver Soft are .................................................................................................................................4

Obtain a DHCP-Assigned IP Address ................................................................................................................... 7

Assign an IP Address Manually...........................................................................................................................9

Disable Bro ser Compatibility Mode ................................................................................................................. 11

Register a PredictPulse Subscription.................................................................................................................. 12

Verifying and Updating the Firm are Revision.................................................................................................. 12

Configuring the Connectivity Card for PredictPulse ............................................................................................ 14

PredictPulse Remote Monitoring Activation Completion Checklist ........................................................................... 19

iv Eaton Power Xpert® Gateway PXGX UPS Card Quick Start Instructions 164950240—Rev 04

Table of Contents

Eaton Power Xpert® Gateway PXGX UPS Card Quick Start Instructions 164950240—Rev 04 1

EEaattoonn PPoowweerr XXppeerrtt GGaatteewwaayy ((PPXXGGXX)) UUPPSS CCaarrdd QQuu cckk SSttaarrtt IInnssttrruucctt oonnss

IInnssttaallllaatt oonn CChheecckkll sstt

1. Verify that the follo ing items are available:

oPo er Xpert Gate ay (PXGX) UPS Card package contents (card, cable, Quick Start Instructions)

oPhillips®scre driver

oAvailable USB port on a computer running Microsoft®Windo s®

oWeb bro ser (Microsoft Internet Explorer®version 8.0 and higher, Mozilla®Firefox®, or

Google Chrome™ are recommended)

2. If you are going to use Dynamic Host Configuration Protocol (DHCP), provide your local net ork

administrator ith the card's MAC address. The MAC address is located on either the shipping box label or

the label on this card.

oMAC Address _______________________________________________

3. If you are not going to use DHCP to provide any of the settings listed belo , contact your local net ork

administrator for the settings.

In the table belo , check the DHCP check box or enter the values for manual configuration. This data is

referenced later in the procedure.

Item DHCP* Manua Configuration

IPv4 oCard IP Address: _______________________________

Netmask: _____________________________________

Gateway: _____________________________________

DNS – Name Servers oName Server #1:________________________________

Name Server #2:________________________________

Name Server #3:________________________________

DNS – Domain oDomain:_________________________________________

* The network administrator normally sets up the DHCP server to provide a static IP address each time the card makes a

DHCP request

4. If you need e-mail functionality, obtain the SMTP mail server's IP address or host name. If using the SMTP

host name, verify that you also have the Name Server IP address (see Step 3).

oSMTP (mail server) IP Address

or Host Name _______________________________________________________________

2 Eaton Power Xpert® Gateway PXGX UPS Card Quick Start Instructions 164950240—Rev 04

IInnssttaallll tthhee CCaarrdd

NOTE The hot-s appable PXGX UPS card can be installed ithout turning off the UPS or

disconnecting the load.

To install the PXGX UPS card:

1. Verify that all six DIP s itches on the card are in the OFF position (see Figure 1).

Figure 1. Verify DIP Switches are OFF

6 5 4 3 2 1

OFF

2. If not already done, record the MAC address for future reference (see the Installation Checklist section).

3. Remove the X-slot®cover from the UPS. Retain the scre s.

NOTE If another card is already installed ith an attached communication cable, disconnect the

cable and then remove the card.

4. To prevent electrostatic discharge (ESD), place one hand on a metal surface, such as the UPS panel.

5. Slide the card into the open slot and secure ith the scre s removed in Step 3 (see Figure 2).

Figure 2. Secure the PXGX UPS Card

6. From your laptop, go to .eaton.com/pxgx.

Power Xpert Gatewa

PXGX UP S

E M P

Upstrea

m Downstrea m

10 010

0 Ac t Ac t Setu p

Restar

Statu

DH C

Iden t

Powe r

Install the Card

Eaton Power Xpert® Gateway PXGX UPS Card Quick Start Instructions 164950240—Rev 04 3

7. On the esources tab, scroll do n and expand the Software, firmware, and applications section link to

do nload the Power Xpert Gateway USB Signed Windows Device Driver.

8. Save the driver configuration file (px-ups-signed-driver.zip) to the C: drive using the default location or a

folder you select. Note the path of the do nloaded file on your computer.

NOTE Do not do nload the file to your desktop.

CCoonnnneecctt tthhee CCaarrdd ttoo tthhee CCoommppuutteerr

To connect the card to the computer:

1. Plug the small connector at the end of the supplied USB configuration cable into the Setup port on the

card (see Figure 3).

Figure 3. Install the USB Cable

Power Xpert Gateway

PXGX UPS

EMP Upstream Downstream

100100 Act Act Setup

Restart

Status

DHCP

Ident

Power

2. Plug the other end of the USB cable into the USB port on the computer. The Windo s operating system

detects ne hard are.

NOTE If a message indicates that the device driver soft are as not successfully installed,

click Ignore.

NOTE You may see a pop-up message indo that sho s “Found ne hard are.” This

indicates that the hard are installed successfully.

3. Connect an active Ethernet cable (not supplied) to the Upstream Ethernet connector on the PXGX UPS

card (see Figure 4).

4. If you are connecting to another PXGX UPS card or other Ethernet device, connect an Ethernet cable (not

supplied) to the Downstream Ethernet connector on the PXGX UPS card.

Connect the Card to the Computer

4 Eaton Power Xpert® Gateway PXGX UPS Card Quick Start Instructions 164950240—Rev 04

Figure 4. Install the Ethernet Cable

Power Xpert Gateway

PXGX UPS

EMP Upstream Downstream

100100 Act Act Setup

Restart

Status

DHCP

Ident

Power

5. Wait for the po er light and status light on the installed card to illuminate. This takes about t o minutes.

6. Open a Web bro ser and type the default IP address (https://169.254.0.101 for firm are 2.6.0.0 or later,

http://192.168.200.101 for earlier firm are versions).

7. Did the Po er Xpert Gate ay soft are open to the PXGX UPS card page?

• If yes, the driver has already been installed automatically. Either verify the IP address assigned

through DHCP or manually enter a static (fixed) IP address for the card’s net ork connection:

a. To verify the DHCP-assigned IP address, go to the Obtain a DHCP-Assigned IP Address section.

b. To manually enter a fixed IP address, go to the Assign an IP Address Manually section.

• If no, the driver has not been installed. Go to the Install the Driver oftware section to confirm that you

have the most current USB Driver soft are. If not, install or update the USB Driver soft are.

IInnssttaallll tthhee DDrr vveerr SSooffttwwaarree

The steps you use to install the driver soft are depend on your operating system (OS). This procedure provides

instructions for installing driver soft are on a Windo s OS.

NOTE You can use either the Device Manager path or the Devices and Printers path to bro se

for the driver soft are and install it. This procedure uses the Device Manager.

To install the driver from the Device Manager:

1. Click Start in the Start bar. Type Device in the search box.

2. Select Device Manager from the list above the search box. The Device Manager displays (see Figure 5).

Install the Driver Software

Eaton Power Xpert® Gateway PXGX UPS Card Quick Start Instructions 164950240—Rev 04 5

Figure 5. Device Manager

3. Expand the Network adapters and Ports (COM & LPT) sections as sho n in Figure 5.

• Look for a USB Serial Device ith a COM port designation (COM4 in the example sho n in Figure 5)

• Unplug the USB connection to the card to verify the correct COM device in the Device Manager

4. Right-click the USB Serial Device (COM#) to display the menu and select Update Driver Software.

• If a pop-up message displays, “The best driver is already installed,” click Close and go to Step 10.

• Other ise, go to Step 5.

5. Select Browse my computer for driver software (see Figure 6). Click Next. The next page displays.

Install the Driver Software

6 Eaton Power Xpert® Gateway PXGX UPS Card Quick Start Instructions 164950240—Rev 04

Figure 6. Update Driver Software Window – Search Method

6. Click Browse. A “Bro se for Folder” dialog displays. Select the folder that contains drivers for your

hard are. Click OK. A “Bro se for driver soft are on your computer” page displays.

7. The path to the po erxpert.inf file displays in the Search for driver software in this location box. Click

Browse and navigate to the po erxpert.inf file you already do nloaded. Select the file and click Next (see

Figure 7).

• If a pop-up message displays, “The best driver is already installed,” click Close and go to Step 10.

• Other ise, the soft are begins to install.

Figure 7. Update Driver Software Window – Browse for Driver Software

8. When the driver soft are is updated successfully, the message “Windo s has successfully updated your

driver soft are” displays (see Figure 8).

Install the Driver Software

Autres manuels pour Power Xpert

Table des matières

Autres manuels Eaton UPS

Eaton

Eaton Powerware 9125 Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

Eaton

Eaton Protection Station 650 Manuel utilisateur

Eaton

Eaton 91PS Manuel

Eaton

Eaton 9PX5KP1 Instructions d'installation et d'utilisation

Eaton

Eaton Powerware 9390 Manuel utilisateur

Eaton

Eaton 9910-E16 Manuel utilisateur

Eaton

Eaton Power Xpert 9395 Manuel utilisateur

Eaton

Eaton 93PM-150(400) Manuel utilisateur

Eaton

Eaton Eaton 5PX Instructions de montage

Eaton

Eaton 9SX EBM 180V Manuel utilisateur

Eaton

Eaton Power Xpert 9395 Manuel utilisateur

Eaton

Eaton 9315 Manuel utilisateur

Eaton

Eaton Powerware 9395 Manuel utilisateur

Eaton

Eaton Power Xpert Plus 1 Manuel utilisateur

Eaton

Eaton 5P 650 AU Manuel utilisateur

Eaton

Eaton Ellipse MAX 600 Manuel utilisateur

Eaton

Eaton Powerware 9395 Manuel utilisateur

Eaton

Eaton Powerware BladeUPS Manuel utilisateur

Eaton

Eaton 9E Manuel utilisateur

Eaton

Eaton Ellipse ECO 500 Manuel utilisateur

Eaton

Eaton 9PX 1000i RT2U Manuel utilisateur

Eaton

Eaton 9E20K-TH Manuel utilisateur

Eaton

Eaton 5S 550 Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur

ZincFive

ZincFive BC Series Manuel utilisateur