Eaton 9SX 15KPM Serie Manuel utilisateur

Eaton 9SX 15-20KPM(AU) Series

Online UPS

Safety Instructions

•SAVE THESE INSTRUCTIONS. See installation instructions before connecting

to the supply. This manual contains important instructions that should be

followed during installation and maintenance of the UPS and batteries.

•In the event of a fire, please use a dry powder fire extinguisher to extinguish

the fire. Do not use liquid fire extinguishers to avoid electric shock.

•The UPS models that are covered in this manual are intended for installation

in an environment within 0 to 50°C, free of conductive contaminant.

Special Symbols

The following are examples of symbols used on the UPS or accessories to alert

you of the below important information:

RISK OF ELECTRICAL SHOCK - Observe the warning associated with the risk of

electrical shock symbol.

Important instructions that must always be followed.

Do not discard the UPS or the UPS batteries in the trash.

This product contains sealed lead acid batteries and must be disposed as

outlined in this manual. For more information, contact your local recycling/reuse

or hazardous waste center.

The crossed-out wheeled bin symbol indicates that electrical and electronic

waste should not be discarded together with general household waste, but must

be collected separately. The product should be handed in for recycling in

accordance to the local environmental regulations for waste disposal.

By separating electrical and electronic waste, you will help reduce the volume of

waste sent for incineration or land-fills and minimize any potential negative

impact on human health and environment.

Information, advice, help.

Refer to the user manual.

Personnel Safety

⚫RISK OF VOLTAGE BACKFEED. This system has its own power source (the

battery). Isolate the UPS and check for hazardous voltage upstream and

downstream during lockout-tagout operation. Terminal blocks may be

energized even if the system is disconnected from the AC power source.

⚫Dangerous voltage levels are present within the system. It should be opened

exclusively by qualified service personnel.

⚫High leakage current, earth connection is essential before connecting to the

supply.

⚫The battery supplied with the system contains small amounts of toxic

materials. To avoid accidents, the directives listed below must be adhered to:

- Servicing of batteries should be performed or supervised by personnels

knowledgeable about batteries and the required precautions taken.

- When replacing batteries, replace with the same type and number of

batteries or battery packs.

- Do not dispose of batteries in a fire. The batteries may explode.

- Batteries constitute a hazard (electrical shock, burns). The short-circuit

current may be very high.

⚫Precautions must be taken for all handling:

- Wear rubber gloves and boots.

- Do not lay tools or metal parts on top of batteries.

- Disconnect charging source prior to connecting or disconnecting battery

terminals.

- Determine if battery is inadvertently grounded. If inadvertently grounded,

remove source from ground. Contact with any part of a grounded battery

can result in electrical shock. The likelihood of such shock can be reduced

if such grounds are removed during installation and maintenance

(applicable to equipment and remote battery supplies not having a

grounded supply circuit).

Product Safety

⚫The UPS connection instructions and operation described in the manual must

be followed in the indicated order.

⚫The upstream circuit breaker for Normal AC / Bypass AC must be easily

accessible. The unit can be disconnected from AC power source by opening

this circuit breaker.

⚫An additional AC contactor is used for backfeed protection and must comply

with IEC/EN 62040-1 (the creep age and clearance distances shall meet the

basic insulation requirements for pollution degree 2).

⚫Disconnection and overcurrent protection devices shall be provided by others

for permanently connected AC input (Normal AC / Bypass AC) and AC output

circuits.

⚫Check that the indications on the rating plate correspond to your AC powered

system and to the actual electrical consumption of all the equipment to be

connected to the system.

⚫For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the

equipment and shall be easily accessible

⚫Never install the system near liquids or in an excessively damp environment.

⚫Never let a foreign body penetrate inside the system.

⚫Never block the ventilation grates of the system.

⚫Never expose the system to direct sunlight or source of heat.

⚫If the system must be stored prior to installation, storage must be in a dry

place.

⚫The admissible storage temperature range is -25°C to +60°C without battery (-

15°C to +40°C with battery).

Special precautions

⚫The unit is heavy: wear safety shoes and use vacuum lifter preferentially for

handling operations.

⚫All handling operations will require at least two people (unpacking, lifting,

installation in rack system).

⚫Straps are provided only for unpacking the unit manually from the carton;

don’t use the straps to carry the unit around. The unit may slip from the

straps during handling (risk of injury and product damage):

- keep 12” / 30cm minimum distance between the straps

- lift the unit carefully and keep it at a low height

- keep the unit horizontal during unpacking.

⚫Before and after the installation, if the UPS remains de-energized for a long

period of time, the UPS must be energized for a period of 24 hours, at least

once every 6 months (for a normal storage temperature less than 25°C). This

charge the batteries, thus avoiding possible irreversible damage.

⚫During the replacement of the Battery Module, it is imperative to use the same

type and number of elements as the original Battery Module provided with

the UPS to maintain an identical level of performance and safety.


 
Contents 
Introduction................................................................................................ 6
1 Environmental protection ............................................................... 6
2 Electronic equipment protection................................................... 7
Presentation ...............................................................................................9
1 UPS Power Module:.......................................................................... 9
2 EBM (External Battery Module):..................................................10 
3 MBP (Maintenance Bypass module): .........................................11 
Mechanical installation.......................................................................... 14 
1 Unpacking and inspection ............................................................14 
3 Mechanical installation..................................................................17 
Cable Connections ..................................................................................21 
1 Input/Output wiring.........................................................................22 
2 External battery module (EBM) Connection ............................. 33 
3 Single MBP Connection .................................................................35 
Parallel UPS installation ......................................................................... 35 
1 Paralleled UPS installation............................................................36 
2 wiring..................................................................................................37 
Communication ports ............................................................................ 42 
Operation interface.................................................................................45 
1 Control panel....................................................................................45 
2 Touch screen ..................................................................................... 46 
3 Operation........................................................................................... 50 
4 UPS Operation .................................................................................56 
Battery maintenance ..............................................................................61 
Troubleshooting.......................................................................................62 
Appendix: General specification ....................................................... 65 
 
 
 
 
 

1. Introduction

Thank you for selecting the Eaton 9SX 15-20KPMAU Series Online UPS to protect

your electrical equipment. These products support dual input requirements, as well

as 4 kinds of input and output modes:

•three phase input - single phase output (3-1)

•three phase input - three phase output (3-3)

•single phase input - single phase output (1-1)

•single phase input - three phase output (1-3)

The 9SX 15-20KPMAU Series features unity power factor output to meet higher real-

power load requirement. ANZ models are configured by default to take 40 blocks of

12V batteries, connected with a neutral point. This can be changed to take 32 blocks

of batteries with a neutral point, only to be done by certified Eaton technicians, and

the use of the correct battery pack. The charging current is adjustable from 1A to 13A.

Units come with gravity sensing coloured LCD touch screen with user friendly

interface for convenient operation. Higher environmental rating is achieved by high

efficiency on the units of: up to 96% in online mode, and up to 95% during battery

mode.

We recommend that you take the time to read this manual to take full advantage of

the many features of your UPS (Uninterruptible Power System).

Before installing your UPS, please read the booklet presenting the safety instructions.

Then follow the indications in this manual.

1.1 Environmental protection

Products are developed according to an eco-design approach.

Substances

This product does not contain CFCs, HCFCs or asbestos.

Packaging

To improve waste treatment and facilitate recycling, separate the various

packaging components.

•The cardboardcomprises over 50% of recycled cardboard.

•Sacks and bags are made of polyethylene.

•Packaging materials are recyclable and bear the appropriate identification

symbol

Materials

Abbreviations

Number in

the symbols

Polyethylene terephthalate

PET

High-density polyethylene

HDPE

Polyvinyl chloride

PVC

Low-density polyethylene

LDPE

Polypropylene

Polystyrene

Follow all local regulations for the disposal of packaging materials.

Product

The product is made up of recyclable materials.

Dismantling and destruction must take place in compliance with all local

regulations concerning waste. At the end of its service life, the product must be

transported to a processing center for electrical and electronic waste.

Batteries

The product contains lead-acid batteries that must be processed according to

applicable local regulations concerning batteries.

The batteries may be removed to comply with regulations and in view of correct

disposal.

1.2 Electronic equipment protection

The uninterruptible power system (UPS) protects your sensitive electronic

equipment from the most common power problems, including power failures,

power sags, power surges, brownouts, line noise, high voltage spikes, frequency

variations, switching transients, and harmonic distortions.

Power outages may occur unexpectedly, with erratic power quality. These power

problems have the potential to corrupt critical data, destroy unsaved work

sessions, and damage hardware - causing hours of lost productivity and

expensive repairs.

With the UPS, you can safely eliminate the effects of power disturbances and

guard the integrity of your equipment. Providing outstanding performance and

reliability, UPS’s unique benefits include:

⚫True online double-conversion technology with high power density, utility

frequency independence, and generator compatibility.

⚫Selectable High Efficiency mode of operation.

⚫Standard communication options: one RS232 communication port, one

USB communication port, one dry in port and dry out port.

⚫Optional connectivity cards with enhanced communication capabilities.

⚫Easy, field upgradable firmware.

Eaton 9SX 15-20KPMAU Dimension:

UPS:

Model name

Size W*H*D(mm)

N.W.(kg)

Note

9SX 15KPM(AU)

438*129 (3U) *559

24.8

Long backup

time model

9SX 20KPM(AU)

438*129 (3U) *559

24.8

Notes:

Total 4 input/output modes are included, default mode: 3-1(single source).

Depth dimension does not include the front panel.

External battery (EBM):

Model name

Size

W*H*D(mm)

N.W.

(kg)

Note

9SX EBM384RT6U

438*129 (3U) *559

51.8

(103.6)

2 EBM /package,

16pcs 9Ah batt./EBM

9SX EBM480RT6U

438*129(3U)*559

60.5

(121)

2 EBM /package,

20pcs 9Ah batt./EBM

Note:

‘Size’is for 1 EBM size, N.W. with (***) is total weight of 2 EBM.

Depth dimension does not include the front panel.

Maintenance ByPass (MBP):

Model name

W*H*D(mm)

N.W. (kg)

Note

MBP20K

438*129 (3U) *465

12.8

single MBP (Basic version)

MBP20KPDU

438*129 (3U) *465

13.6

single MBP

(Standard version)

MBP20KPARA

438*129 (3U) *465

19.9

1+1 parallel MBP

(Standard version)

Note:

1. Default is setting with the mode:3-1(single source).

2. Depth dimension does not include front panel.

2. Presentation

2.1 UPS Power Module:

Front view

Note:

1. Ventilation area

2. LCD Module, including:

2(1): Power button，2(2): Touch screen，2(3): LED indicator

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Eaton UPS

Eaton

Eaton SU700XLCD Manuel utilisateur

Eaton

Eaton 5P1000RC Manuel utilisateur

Eaton

Eaton EX 2200 RT 2U Manuel utilisateur

Eaton

Eaton 9SX Series Manuel utilisateur

Eaton

Eaton Power Xpert 9395 Manuel du propriétaire

Eaton

Eaton Powerware 5115 Manuel utilisateur

Eaton

Eaton Single EBC Manuel utilisateur

Eaton

Eaton Tripp Lite SmartOnline Series Manuel utilisateur

Eaton

Eaton 5E 500 Manuel utilisateur

Eaton

Eaton 9E15Ki Manuel d'instructions

Eaton

Eaton Powerware 5125 Instructions d'utilisation et de sécurité

Eaton

Eaton powerwave 9315 Manuel utilisateur

Eaton

Eaton Pulsar Series 650 Manuel utilisateur

Eaton

Eaton Powerware 9140 Manuel utilisateur

Eaton

Eaton 3SMini Manuel utilisateur

Eaton

Eaton BladeUPS none Manuel utilisateur

Eaton

Eaton Powerware 9355 Manuel utilisateur

Eaton

Eaton RT 1250VA Manuel utilisateur

Eaton

Eaton 9E 10000i Manuel utilisateur

Eaton

Eaton ModularEasy 9PXMEZ6Ki Manuel utilisateur

Eaton

Eaton 93PM IBC-L Manuel utilisateur

Eaton

Eaton 93PM IBC-L Manuel

Eaton

Eaton 3S Manuel utilisateur

Eaton

Eaton 93E MK2 Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur

ZincFive

ZincFive BC Series Manuel utilisateur