Eaton EF-CBD130 Manuel utilisateur
EF-CBD130 Conventional Reflective Beam Detector
Installation and operation manual
2INSTALLATION AND OPERATION MANUAL 25-17603-C March 2023 www.eaton.com
Contents
DOCUMENT UPDATE NOTES....................................3
1. IMPORTANT PRODUCT SAFETY INFORMATION ..................3
1.1. Definitions and Symbols..........................................3
2. ABOUT THE EF-CBD130.......................................4
2.1. Feature and Benefits ............................................4
2.2. Technical Specifications ..........................................5
2.3. Product Appearance ............................................6
2.4. Principle of the Beam Detector ....................................6
3. INSTALLATION PROCEDURES .................................7
3.1. Mounting Details ...............................................7
3.2. LED Indicators .................................................7
3.3. Mounting Preparation ...........................................8
3.4. Mounting of the Beam Detector ...................................9
3.5. Mounting of the EF-CBD130-R Reflector.............................9
3.6. Cabling Details................................................10
4. PROGRAMMING SENSITIVITY AND SPAN ......................11
5. COMMISSIONING BEAM DETECTOR ..........................11
5.1. Commissioning Preparation ......................................12
5.2. Step 1: Entering Commissioning Method ...........................12
5.3. Step 2: Sightline Alignment Procedure .............................12
5.4. Step 3: Acceptable Adjustment Procedure ..........................12
5.5. Step 4: Finalizing Installation .....................................13
5.6. Step 5: Testing Fire Signal .......................................13
5.7. Step 6: Testing Fault Signal ......................................13
6. OTHER FUNCTIONS ........................................14
7. MAINTENANCE ............................................15
8. TROUBLESHOOTING GUIDE..................................15
9. SUPPLIED ACCESSORIES ....................................15
10. APPENDIX 1 ..............................................16
10.1. Limitation of Beam Detectors ...................................16
3INSTALLATION AND OPERATION MANUAL 25-17603-C March 2023 www.eaton.com
DOCUMENT UPDATE NOTES
S.No. Release / Change Notes Date
AEaton update - first release July 2022
Eaton update - supplied accessories March 2023
1. IMPORTANT PRODUCT SAFETY INFORMATION
To prevent severe injury and loss of life or property, read the instruction carefully
before installing the beam detector to ensure proper and safe operation of
the system.
1.1. Definitions and Symbols
WARNING
Indicates a potentially hazardous situation which, if not avoided, can result in
serious injury or death.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, can result in
minor to moderate injury, or serious damage to the product.
This product must only be disposed of in
accordance with the WEEE directive.
0832
DoP0506-UK
22
2831
DoP0506
22
EN54-12:2015
378aa/01
Eaton Electrical Products Ltd.
Llantarnam Park
Cwmbran
NP44 3AW
EF-CBD130 2831-CPR-F4717
EF-CBD130 0832-UKCA-CPR-F1371
EN54 Part 12 Compliance
EF-CBD130 Conventional Reflective Beam Detector
complies with the requirements of EN 54-12:2015.
C Eaton update
B
C
Eaton update - images and layout July 2022
4INSTALLATION AND OPERATION MANUAL 25-17603-C March 2023 www.eaton.com
2. About the EF-CBD130
2. About the EF-CBD130
The EF-CBD130 reflective beam detector is for use with the Eaton range of
conventional fire systems. Alignment is made easy with a built in laser pointer and
digital display.
The laser pointer is used to mark the exact location where the reflector is to be
installed. Once the reflector is installed the digital display indicates the light intensity
between the detector and the reflector enabling the user to adjust for optimal
alignment
The EF-CBD130 has four adjustable operational ranges of between 8 to 20, 20 to 40,
40 to 70 and 70 to 100 meters beside with three adjustable sensitivity setting ranges
from 2.6dB, 3.8dB and 5.8dB to meet the specific environmental requirement. The
EF-CBD130 works on the principle of reflective infrared beam obscuration. Used in
conjunction with a reflector, it will notify the fire alarm panel when the infrared beam
is obscured by smoke.
The EF-CBD130 is ideal for use high ceiling and wide areas such as warehouses,
large stores, shopping malls, leisure centres, exhibition halls, hotel lobbies, printing
houses, garment factories, museums and prisons, as well as places where slight
smoke particles or corrosive gas exist.
2.1. Feature and Benefits
1. EN54-12 Compliance
2. Intuitive alignment with built in laser pointer and digital display
3. Employ single-ended design through reflector
4. Four ranges wide monitoring from 8-100 meters via encoder
5. Three users programing sensitivity adjustment
6. Built-in microprocessor
7. Self-diagnosis function can monitor for internal faults
8. Automatic compensation for factors weakening received signals, such as
dust contamination, positional movement and ageing of the transmitter
9. Fire and Fault interfacing relays
10. Aesthectically pleasing
5INSTALLATION AND OPERATION MANUAL 25-17603-C March 2023 www.eaton.com
2. About the EF-CBD130
2.2. Technical Specifications
Part Number EF-CBD130
Standard
Listed LPCB Certification
Compliance EN 54-12:2015
Fire Detection and Alarm Systems BS 5839 Part 1:2017
Specification
Operating Voltage 20 V to 28 V DC
Current Parameters Standby: 23mA Commission: 56mA Alarm: 33mA
Beam Sensor Sensitivity [via Encoder] Level 1: 2.6 dB High Sensitivity
Level 2: 3.8 dB Medium Sensitivity
Level 3: 5.8 dB Low Sensitivity
Beam Pathway Length [via Encoder] Span 1: 8 to 20 meters Limited Path
Span 2: 20 to 40 meters Short Path
Span 3: 40 to 70 meters Normal Path
Span 4: 70 to 100 meters Long Path
Beam Path Angle ±0.4º Directional (This data takes the average of the left and right
deflection angles.)
Alignment Guide Laser Beam Pointer
Digital Display Guide Nixie Tube
LED Indicator Guide Red: Fire ; Yellow: Fault ; Green: Alignment
Reset Time Less than 2 Second
Relay Capacity [Fire & Fault] Normally Open & Close/ 2.0 A; 30 VDC
Physical
Material / Colour ABS / White
Dimension / Weight L:190.87 x W:126.87 x H:91.96 mm / 440 gm
Weight 0.130 Kg with base
Environmental
Operating Temperature -10°C to +50°C
Ingress Protection Rating IP30 [IP66 glue seal-For permanent fixing, Not EN54-12 approved]
Humidity 0 to 95% Relative Humidity, Non condensing
6INSTALLATION AND OPERATION MANUAL 25-17603-C March 2023 www.eaton.com
2. About the EF-CBD130
2.3. Product Appearance
2.4. Principle of the Beam Detector
In a fire, when smoke enters the path of the beam detector, some of the light
is absorbed or scattered by the smoke particles. This decreases the received
signal, leading to an increase in optical obscuration. This unit decodes the received
signals and compares to the pre-programmed algorithm stored on the processor.
Through this algorithm the detector will take appropriate action and activate the
corresponding relays and LED indicators.”
To avoid false alarms the detector and reflector should be mounted on a solid
structure, care should be taken to avoid obstructing the path of the beam. Refer to
Figure 1.
In operation mode, the unit continually emits light, care should be taken that the
activities in the space do not obstruct the beam or move the device to avoid false
operation of the detector. Refer to Figure 1.
Smoke
Fire Status
Beam
Detector
Mounting
Bracket
Reector Beam
Detector
Mounting
Bracket
Normal Status
Reector
Figure 1. Beam detector principle 2 Installation Procedures
2. About the EF-CBD130
7INSTALLATION AND OPERATION MANUAL 25-17603-C March 2023 www.eaton.com
3. Installation Procedures
3. Installation Procedures
3.1. Mounting Details
79mm
85mm
158.5mm
158.5mm
AlignmentFault
Fire
39.54mm
30.53mm
AlignmentFault
Fire
71.8mm 5.89mm
Figure 2. Detector Diagram
3.2. LED Indicators
LED Indicators Colour Function
Fire Red Illuminates when at least one fire alarm event occurs
Fault Yellow Illuminates when at least one fault alarm event occurs in the detector
Alignment Green Illuminates during commissioning
8INSTALLATION AND OPERATION MANUAL 25-17603-C March 2023 www.eaton.com
2. About the EF-CBD130
3.3. Mounting Preparation
This beam detector must be installed, commissioned and maintained by competent
personnel. The installation should comply with all local standards and/or codes of
practice in the region.
Note - to avoid damage to critical components such as the reed switch it is advisable
to use the magnetic tool when needed.
If the ceiling height is less than 8 meters, the beam detector should be
installed between 0.5 meters to 1 meter below the ceiling level. Refer to Figure 3.
If the ceiling height is more than 8 meters, the beam detector should be
installed at least 0.5 meters below the ceiling. Refer to Figure 3.
The chosen location should be clean and dry and not subject to shock,
vibration, electro-statistic discharge, and free from glass walls, direct sunlight and
any reflective barriers.
Make sure that the beam path is free from obscuration caused by moving
items.
0.5m min to 1m max
Beam
Detector
Beam
Detector
0.5m min
Below 8 meters ceiling height Above 8 meters ceiling height
Figure 3. Installation Details
9INSTALLATION AND OPERATION MANUAL 25-17603-C March 2023 www.eaton.com
2. About the EF-CBD130
3.4. Mounting of the Beam Detector
1. Using the supplied bracket, mark the position of the fixing holes.
2. Fit the mounting bracket using appropriate fixings for the surface, ensure
that the bracket is secure and free from movement. Refer to Figure 4
3. Fix the detector base onto the bracket using two M4x12x10 standard screws.
79mm
85mm
158.5mm
158.5mm
Figure 4. Mounting Bracket Figure 5. Beam Detector
3.5. Mounting of the EF-CBD130-R Reflector
1. For distances between 8m and 40m one reflector is required, for distances
between 40m and 100m four reflectors are required
2. Mark the position of the fixing holes
3. Fit the reflector with suitable fixings. Refer to Figure 6.
10 INSTALLATION AND OPERATION MANUAL 25-17603-C March 2023 www.eaton.com
2. About the EF-CBD130
Beam
Detector
Line-of-Sight Distance
8 to 40m (1 x reector)
Reector 1 x Reector
122mm
100mm
244mm
200mm
4 x Reector
40m to 100m (4 x reector)
Figure 6. Mounting of EF-CBD130-R Reflector Reflector
3.6. Cabling Details
Cables should be brought into the detector using the supplied cable gland.
The maximum size of the cable which can be terminated is 1.5mm².
Observe the polarity. Refer to Figure 7.
1. Terminal D1 (+) and D2 (-) for connecting Power supply [24VDC]
2. Terminals S1(+) and S2(-) to be linked to D1 (+) and D2 (-)
3. Terminal HJ1 and HJ2 for connecting Fire signal relay output
[Normally Open]
4. Terminal GZ1 and GZ2 for connecting Fault signal relay output
[Normally Close]
Figure 7. Wiring Terminals
Table des matières
Autres manuels Eaton Capteur de sécurité
Eaton
Eaton 1450-CSA Manuel
Eaton
Eaton NexiTech Series Manuel utilisateur
Eaton
Eaton CWGA-0 Series Manuel
Eaton
Eaton xComfort CSEZ-01/06 Manuel utilisateur
Eaton
Eaton MAB50R Manuel utilisateur
Eaton
Eaton Powerware Series Manuel utilisateur
Eaton
Eaton MPAD-C-A Manuel utilisateur
Eaton
Eaton PPD-C-230V Manuel utilisateur
Eaton
Eaton All-Pro MS245RW Manuel utilisateur
Eaton
Eaton DET-REXT-PIR30 Manuel utilisateur
Eaton
Eaton CEAG EURO X LED Manuel de service
Eaton
Eaton URTDII Manuel
Eaton
Eaton 2450 Series Manuel utilisateur
Eaton
Eaton MEM Watchman 180 Manuel utilisateur
Eaton
Eaton COOPER POWER SERIES Manuel utilisateur
Eaton
Eaton HALO MS180 Manuel utilisateur
Eaton
Eaton Velos Manuel utilisateur
Eaton
Eaton MAP820 Manuel d'instructions
Eaton
Eaton CEAG 6811 LED CGLine+ Manuel de service
Eaton
Eaton Crouse-hinds series Manuel utilisateur
