Eaton Powerware Series Manuel de programmation

Powerware Series

Eaton ConnectUPS Web /SNMP Card

Quick Start Instructions

X and BD Models

Eaton, Powerware, LanSafe, and PowerVision are registered trademarks and ConnectUPS, X-Slot,

BestDock, and CoreLogic are trademarks of Eaton Corporation or its subsidiaries and affiliates.

Microsoft and Windows are registered trademarks of Microsoft Corporation. HyperTerminal is a

registered trademark of Hilgraeve. Modbus is a registered trademark of Modicon. IBM and AS/400 are

registered trademarks of International Business Machines, Inc. All other trademarks are property of

their respective companies.

document may be reproduced in any way without the express written approval of Eaton Corporation.

Eaton®ConnectUPStWeb/SNMP Card (X and BD Models) Quick Start Instructions 164950185 Rev B

www.eaton.com/powerquality

Checklist

1. Verify that all of the following items are available:

JConnectUPS Web/SNMP Card package contents (see

front cover)

JPhillips screwdriver

JMicrosoftRWindowsRoperating system (for other operating

systems, see the help file on the Software Suite CD)

JAvailable serial port (RS-232)

JHyperTerminalR(ships with Windows) or equivalent

terminal emulation application

JInternet Explorer Web browser

2. Contact your local network administrator for the following

mandatory network settings:

JIP Address (static address*)

JGateway IP Address

JNetwork Mask IP Address

*If you are setting up the ConnectUPS Card in a DHCP

environment, the network administrator must set up the

DHCP server to provide a static address each time the card

makes a DHCP request. Provide the network administrator

with the card's MAC address (on the bottom of the card):

JMAC address

3. If you need e-mail functionality, obtain the following network

settings (either SMTP only or DNS and Host Name):

JSMTP (mail server) IP Address

JDNS (name server) IP Address

JHost Name

Refer to the ConnectUPS Web/SNMP Card User's Guide

PDF on the Software Suite CD for detailed setup information.

4. List the applicable UPS load segment (receptacle group)

connections (refer to the UPS user's guide to see if load

segments are available for your UPS):

JLoad Segment 1 is connected to

JLoad Segment 2 is connected to

JLoad Segment 3 is connected to

Examples of load segment equipment connections are

“CPU MX1,” “Monitor MX1,” and “Router San Diego 1.”

Eaton®ConnectUPStWeb/SNMP Card (X and BD Models) Quick Start Instructions 164950185Rev B

www.eaton.com/powerquality

Figure 1. Verify DIP Switches

Figure 2. Install the ConnectUPS Card

Figure 3. Secure the ConnectUPS Card

Figure 4. Install the Ethernet Cable

Eaton®ConnectUPStWeb/SNMP Card (X and BD Models) Quick Start Instructions 164950185 Rev B

www.eaton.com/powerquality

Section 1

Install the Card

The hot-swappable ConnectUPS Web/SNMP Card can be

installed without turning off the UPS or disconnecting the load.

The following steps explain how to install the ConnectUPS-X or

ConnectUPS-BD:

1. Verify that both DIP switches on the card are set to the 0

(off) position (see Figure 1).

NOTE If you are setting up the ConnectUPS Card in a

DHCP environment, set DIP switch 2 to the 1(on) position.

2. Remove the X-Slottor BestDocktcover on the UPS rear

panel. Retain the screws.

NOTE If there is another card already installed with an

attached communication cable, disconnect the cable and

then remove the card.

3. To prevent electrostatic discharge (ESD), place one hand on a

metal surface such as the UPS rear panel.

4. Slide the card into the open slot and secure with the screws

removed in Step 2 (see Figure 2 and Figure 3).

5. Connect an active Ethernet cable (supplied) to the Uplink

Ethernet connector on the ConnectUPS-X or to the network

connector on the ConnectUPS-BD (see Figure 4).

6. To configure the card locally using the supplied configuration

cable, continue to the following section, “Connect the Card.”

To configure the card remotely through a network using a

Web browser or Telnet (or similar) utility, refer to the

ConnectUPS Web/SNMP Card User's Guide PDF on the

Software Suite CD.

Figure 5. Install Configuration Cable

Figure 6. Select Connection

Figure 7. Configure Port Settings

Figure 8. Enter Configuration Password

Eaton®ConnectUPStWeb/SNMP Card (X and BD Models) Quick Start Instructions 164950185Rev B

www.eaton.com/powerquality

Section 2

Connect the Card

To connect the card to the computer and start the configuration:

1. Plug the RJ-45 end of the supplied configuration cable

(labeled “PC”) into the COM port on the card (see Figure 5).

Verify that you have used the port labeled “COM.” The

other ports on the card will not work for configuration.

2. Plug the other end of the serial cable into the serial COM port

on the computer.

3. Open your terminal emulation program (such as

HyperTerminal).

4. Select the appropriate serial connection (such as COM1). See

Figure 6.

5. Set the serial line to 9600 baud, No parity, 8 data bits, 1 stop

bit, and no flow control (see Figure 7).

6. Verify that the UPS is turned on.

7. After a few seconds, press Enter. The Password prompt

appears (see Figure 8).

If the Password prompt does not appear, press Enter again.

If it still does not appear, check the following conditions:

SVerify the serial line is set to 9600 baud, No parity, 8 data

bits, 1 stop bit, and no flow control.

SIf the serial line settings are correct, check the cabling to

verify all connections are secure.

SVerify that your terminal program is on the correct

communication port for the serial connection.

SVerify that the card has power (one or more LEDs on the

card are illuminated). The UPS should be turned on.

8. Type your password (the default is admin) and press Enter.

The Main Menu screen appears.

Figure 9. Configure Card Settings

Figure 10. Set ConnectUPS Card IP Address

Figure 11. Save and Exit

Figure 12. ConnectUPS Card Summary Page

Eaton®ConnectUPStWeb/SNMP Card (X and BD Models) Quick Start Instructions 164950185 Rev B

www.eaton.com/powerquality

Section 3

Configure the Card

To configure the card after you have connected it:

1. Type 1on the Main Menu to display the Web/SNMP Card

Settings screen (see Figure 9).

2. Type 1to display the Set the IP Address, Gateway Address

and MIB System Group screen (see Figure 10).

3. To set the IP Address, type 1and press Enter. Type the IP

Address and press Enter. (see the Checklist).

4. Type 0to return to the previous menu.

5. Repeat Steps 3 and 4 to set the Gateway Address and

Network Mask.

6. Change any other options as needed for your particular

configuration by typing the corresponding number shown in

the menu.

Each Configuration Menu setting is described in detail in

the Appendix of the ConnectUPS Web/SNMP Card User's

Guide. You can change the other options later if you prefer.

7. Type 0until you return to the Main Menu (see Figure 11).

8. Type 0to save all settings and exit the card configuration.

9. Verify network communication by using a Web browser (see

Figure 12). Type the IP Address of your card and select Go.

The ConnectUPS Card summary page opens.

NOTE Once the card is reachable on the network, you can

use a Web browser, Telnet, or similar utility to adjust any of

the configuration settings. The menus are identical to those

seen during serial configuration and are password-protected

for Superuser access only.

Figure 13. Install NetWatch Software

Figure 14. Launch NetWatch Software

Figure 15. Enter ConnectUPS Card IP Address

Figure 16. Select UPS Load Segment

Eaton®ConnectUPStWeb/SNMP Card (X and BD Models) Quick Start Instructions 164950185Rev B

www.eaton.com/powerquality

Section 4

Install Shutdown Software

NOTE The following procedure applies to NetWatch shutdown

software for Microsoft Windows operating systems. For other

operating systems, refer to the NetWatch help file on the CD.

NOTE For other software, such as LanSafeR

Power

Management Software or PowerVisionR

Software, refer to those

user guides for instructions.

Use the following procedure to install NetWatch software after

you have installed and configured the card:

1. Insert the Software Suite CD into the computer's CD-ROM

drive. The CD menu displays after a few seconds.

2. Select Software Wizard from the Main Menu.

3. Select Install NetWatch (see Figure 13).

4. Select the operating system.

5. Select Launch the Installer (see Figure 14).

6. Select Open in the File Download dialog box and follow the

installation instructions until the Select Powerware Shutdown

Server window displays.

7. Select Manually Enter IP Address for the Shutdown Server

(see Figure 15).

8. Type the IP Address of the card and select OK.

9. Select the correct UPS load segment that your computer's

power cord is plugged into and select OK (see Figure 16).

Figure 17. Verify Configuration Settings

Figure 18. Verify Configuration Settings

Figure 19. Verify Configuration Settings

Figure 20. Clear Communication Message

Eaton®ConnectUPStWeb/SNMP Card (X and BD Models) Quick Start Instructions 164950185 Rev B

www.eaton.com/powerquality

10. Select your preferred method of shutting down your system

(see Figure 17). The default selection is recommended.

Select Next.

11. The Event and Logging Options dialog opens (see Figure 18).

Select Next.

12. Verify the configuration settings are correct and select Finish

(see Figure 19).

13. A pop-up message indicates that communication with the

card is established (see Figure 20). Select Clear to

acknowledge the message.

14. Repeat Steps 1 through 13 on all computers powered by the

corresponding UPS using this specific card.

NetWatch installation and configuration is now complete.

Eaton®ConnectUPStWeb/SNMP Card (X and BD Models) Quick Start Instructions 164950185Rev B

www.eaton.com/powerquality

Autres manuels pour Powerware Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Eaton Carte réseau

Eaton

Eaton Network-MS Manuel utilisateur

Eaton

Eaton DeviceNet Product Operated Network Interface Manuel

Eaton

Eaton -66103 Manuel utilisateur

Eaton

Eaton Network-M2 Manuel utilisateur

Eaton

Eaton 34003991EN/EB Manuel utilisateur

Eaton

Eaton DeviceNet Starter Network Adapter D77B-DSNAP Manuel utilisateur

Eaton

Eaton Network-M3 Manuel utilisateur

Eaton

Eaton Network-M2 Manuel utilisateur

Eaton

Eaton Network Card-MS Manuel utilisateur

Eaton

Eaton POW-R-COMMAND 1000 Manuel utilisateur

Eaton

Eaton Network Card-MS Manuel utilisateur

Eaton

Eaton Network Management Card Manuel utilisateur

Eaton

Eaton PXGMS Power Xpert Gateway Minislot UPS Manuel utilisateur

Eaton

Eaton Power Xpert Meter 2000 Manuel utilisateur

Eaton

Eaton Modbus MS Card Manuel utilisateur

Eaton

Eaton QSNAP Manuel utilisateur

Manuels Carte réseau populaires d'autres marques

FirstComm

FirstComm OBiWiFi5G Manuel utilisateur

Sun Microsystems

Sun Microsystems Interface Adapter Manuel utilisateur

TRENDnet

TRENDnet TU2-ETG Manuel utilisateur

YASKAWA

YASKAWA SI-EN3 Manuel utilisateur

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuel utilisateur

Belkin

Belkin F5D7050 Manuel utilisateur

3Com

3Com EtherLink 3C509B Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITX Manuel utilisateur

Cisco

Cisco MC16E Manuel utilisateur

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuel utilisateur

TwinMOS

TwinMOS Booming Manuel utilisateur

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur

National Instruments

National Instruments NI 9234 Manuel utilisateur

Hama

Hama 49276 Manuel utilisateur

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuel d'utilisation

Compaq

Compaq Wireless LAN 100 Manuel utilisateur

Bose

Bose PowerMatch Dante Manuel utilisateur