Eaton Network Management Card Manuel utilisateur

www.eaton.com

Network Management Card

(Network-MS)

User manual

Network Management Card – User Manual 34003991XT_EN/EF Page 1/127

Network Management Card – User Manual 34003991XT_EN/EF Page 2/127

Contents

1EATON NETWORK SOLUTION 6

1.1 GENERAL PRESENTATION 6

1.1.1 Connecting the UPS to the Ethernet network 7

1.1.2 Protection of the computers/servers 7

1.1.3 Supervision of the UPSs over the network 8

1.1.4 Connection 8

1.2 PRESENTATION OF THE NETWORK MANAGEMENT CARD (NMC) 10

1.2.1 Compatibility with UPSs 10

1.2.2 Direct sending of E-mail 10

1.2.3 Sending text messages (SMS) 11

1.2.4 Compatibility with the Network Management Systems (NMS) – Trap sending 11

1.2.5 Environment Sensor (option) 11

1.3 TECHNICAL DATA 12

1.3.1 Hardware characteristics 12

1.3.2 EMC Compatibility 12

1.3.3 Configuration 12

1.3.4 Administration 13

1.3.5 Network 13

1.3.6 Environment sensor 13

1.3.7 MIB (Management Information Base) 14

1.3.8 Default parameters 15

2INSTALLATION 17

2.1 UNPACKING AND CHECK ON CONTENTS 17

2.2 INDICATIONS 17

2.3 INSTALLATION IN THE UPS 18

2.4 SENSOR INSTALLATION (OPTION)19

3CONFIGURATION 20

3.1 CONFIGURE IP PARAMETERS 20

3.1.1 Your network is equipped with a DHCPv4 server 21

3.1.2 Your network is not equipped with a DHCPv4 server 22

3.1.3 IPv6 Parameters 22

3.2 TEST AFTER CONFIGURATION 22

4SUPERVISION AND ADMINISTRATION BY BROWSER 23

4.1 OPTIMISING THE PERFORMANCE OF YOUR BROWSER 23

4.2 UPS 24

4.2.1 UPS properties page 24

4.2.2 On-line help 36

Network Management Card – User Manual 34003991XT_EN/EF Page 3/127

4.2.3 Logging In 37

4.2.4 UPS control 38

4.2.5 UPS weekly schedule programming 40

4.2.6 Shutdown parameters 41

4.2.7 Measurements 43

4.2.8 Event log 44

4.2.9 System log 45

4.3 NOTIFICATION 46

4.3.1 Email Notification 46

4.3.2 E-mail Message Settings 48

4.4 CONFIGURATION 50

4.4.1 Network settings 50

4.4.2 System 53

4.4.3 Notified Applications 54

4.4.4 Central shutdown configuration 56

4.4.5 Access control 58

4.4.6 SNMP Setting 59

4.4.7 Date and time 62

4.4.8 Firmware upload 64

4.5 ENVIRONMENT SENSOR (OPTION)65

4.5.1 Characteristics 65

4.5.2 Environment Status 66

4.5.3 Environment Settings 67

4.5.4 Log 69

5SERVER PROTECTION 70

5.1 SET-UP OF THE SHUTDOWN PARAMETERS 70

5.1.1 Shutdown criteria managed by the Network Management Card 70

5.1.2 Controlled outlets 73

5.1.3 Protection of a server connected to a controlled outlet 73

5.2 THE DIFFERENT SERVER AND UPS SHUTDOWN SEQUENCES 75

5.2.1 Extended power outage, shutdown initiated by the Shutdown Timer (Shutdown after) 75

5.2.2 Extended power outage, shutdown initiated by the "Low battery power" message 75

5.2.3 Case of power restoration before the end of the "shutdown duration" counter 76

5.3 SHUTDOWN MANAGEMENT WITH 2NMC BOARDS 77

5.3.1 Shutdown Duration 77

5.3.2 Settings 77

6TELNET/SSH/CLI INTERFACES 78

6.1 INTRODUCTION 78

6.2 SETTINGS LIST 78

6.2.1 Network settings 78

Network Management Card – User Manual 34003991XT_EN/EF Page 4/127

6.2.2 System settings 79

6.2.3 Trap receivers 79

6.2.4 Access control 79

6.2.5 Shutdown settings 79

6.2.6 SNMP settings 80

6.2.7 Date and time 80

6.2.8 Environment settings 80

6.3 MENU INTERFACE 81

6.3.1 Tree description 82

6.3.2 Main menu 83

6.3.3 Reset item 83

6.3.4 Network menu 83

6.3.5 Trap receivers menu 86

6.3.6 System menu 86

6.3.7 Shutdown menu 87

6.3.8 Access Control menu 88

6.3.9 Date and time menu 89

6.3.10 Environment menu 89

6.3.11 Return to default Login/Password 91

6.3.12 Return to default configuration 91

6.4 COMMAND LINE INTERFACE 92

6.4.1 Generic command 92

6.4.2 Network settings 93

6.4.3 Trap receivers 96

6.4.4 System settings 97

6.4.5 Shutdown settings 98

6.4.6 Access control settings 99

6.4.7 Date and time settings 100

6.4.8 Environment settings 101

6.5 CONSTRAINTS/LIMITATIONS 104

7CONFIGURATION VIA RS232 105

7.1 CHOICE 1: RESTART /RESET 106

7.2 CHOICE 2: NETWORK CONFIGURATION 106

7.2.1 Choice 1: Read IPv4&IPv6 Network settings 106

7.2.2 Choice 2: Modify IPv4 Network settings 107

7.2.3 Choice 3: Set Ethernet speed 107

7.3 CHOICE 3: LOST PASSWORD /SET LOGIN PASSWORD TO DEFAULT 108

7.4 CHOICE 4: RETURN TO DEFAULT CONFIGURATION 109

8APPENDIX 110

8.1 TABLES OF ALARMS AND EVENTS 110

Network Management Card – User Manual 34003991XT_EN/EF Page 5/127

8.1.1 Table of alarms 110

8.1.2 Table of UPS events 113

8.1.3 Table of system alarms 116

8.2 SNMP OBJECTS 117

8.2.1 IETF MIB 117

8.2.2 EATON Pulsar MIB (ex MGE) 117

8.2.3 TRAPS table: (1.3.6.1.4.1.705.1.11) 120

8.2.4 EATON Powerware MIB 121

9GLOSSARY 125

Network Management Card – User Manual 34003991XT_EN/EF Page 6/127

1 EATON Network Solution

1.1 General Presentation

EATON Network Solution:

Provides information on events concerning the supply of power to the computers connected to your network,

Carries out automatic shutdown of computer systems,

Monitors and controls all the UPSs connected to the network.

EATON Network Solution provides 3 main functions:

Supervision of the UPSs over the Network: Web browser, Intelligent Power Manager, or SNMP Network

Management System (NMS).

Protection of the computers (multi-platform) with Intelligent Power Protector

Connexion of the UPS to the Network.

Network Management Card – User Manual 34003991XT_EN/EF Page 7/127

1.1.1 Connecting the UPS to the Ethernet network

This function can be performed through network Cards inserted in the UPS (Network Management Card).

Also a software "agent" running on a nearby PC that is called the IPP Shutdown controller feature can be used.

IPP Shutdown controller feature allows USB or Serial connected UPS to be seen on the network through the PC.

The Network Management Card or Proxy:

Manages communication with the UPS (as well as local protection of the machine on which Proxy is installed).

Periodically accesses the information concerning the UPS.

Makes this information available to the connected applications (Intelligent Power Protector, Web Browser,

Network Management Systems, Intelligent Power Manager).

Sends notifications on certain events.

Operation may be in standard secure mode (the default mode) or in SSL secured mode (Secure Socket Layer

SSL).

1.1.2 Protection of the computers/servers

This function is performed by Intelligent Power Protector installed on each of the computers to be protected.

Note that Intelligent Power Protector are available on several Operating Systems.

Protection applications:

Continuously gets information from the Network Management Card/Proxy connected to the UPS.

Warns administrators and users if AC power fails and proceeds to a graceful system shutdown before the end of

battery backup power is reached.

Network Management Card – User Manual 34003991XT_EN/EF Page 8/127

1.1.3 Supervision of the UPSs over the network

Depending on your needs, you can either use:

Internet browser to monitor each UPS, as IPP Shutdown Controller and Management Card includes a Web server

Company’s standard Network Management System (HP-Openview, CA Unicenter, HP Insight Manager, IBM

Tivoli Netview)

To simplify integration of EATON UPSs, use one of the Network Management System Kits for EATON devices.

These kits are available on the Software Suite CD-ROM or on the http://powerquality.eaton.com website.

The supervisor "Intelligent Power Manager".

1.1.4 Connection

Before installing the Network Solution, the UPS must be set up as indicated in the steps below.

Shut down the computers to be protected by the UPS.

Connect the UPS to a wall outlet. (For UPSs above 3kVA, please refer to the UPS installation manual).

Connect the power cord of each computer to an outlet on the UPS. (For more details, please refer to the UPS

installation manual)

Network Management Card – User Manual 34003991XT_EN/EF Page 9/127

1.1.4.1 How to connect UPS / agent / network:

Insert the optional NMC communication card in the UPS and connect the UPS to the computer network.

Start the UPS, then the computers.

1.1.4.2 Setting up the protection:

Set up the Network Management Card (see user manual).

Install and configure the protection application on all machines that are to be protected by the UPS:

Intelligent Power Protector for EATON Pulsar series UPS: The software components for each platform and the

user manuals are on the Software Suite CD or available at http://powerquality.eaton.com

Network Management Card – User Manual 34003991XT_EN/EF Page 10/127

1.2 Presentation of the Network Management Card (NMC)

1.2.1 Compatibility with UPSs

The Minislot Network Management Card is compatible with the UPS listed into the compatibility list:

Pulsar MX All models

MX, MX frame All models

Pulsar M 2200 / 3000 All models

Pulsar 700 / 1000 / 1500 All models

EX 700 / 1000 / 1500 / 2200 / 3000 All models

Evolution 650 / 850 / 1150 / 1550 / 2000 All models

Evolution S 1250 / 1750 / 2500 / 3000 All models

Pulsar Evolution 500 / 800 / 1100 Technical level 06 or higher

Pulsar Evolution 2200 / 3000 Technical level 05 or higher

Pulsar Evolution 1500 Technical level 05 or higher

EXtreme C 700 / 1000 / 1500 Technical level B2 or higher

EXtreme C 2200 - 3200 Technical level 02 or higher

Pulsar EX 700 / 1000 / 1500 RT (US°) Technical level 03 or higher

Pulsar EX 2200 / 3200 (US°) Technical level 09 or higher

EX 5 / 7 / 11 RT Equiped with Minislot port.

Powerware 5130 All models

9120 All models

9130 All models

9135 All models

9170 All models

Network Management Card acquires information regarding the operation status of the UPS systems and provides

remote control of the system through the ETHERNET network from any SNMP administration station or Web

browser.

NMC also supplies alarms to the Intelligent Power Protector in order to trigger shutdowns or manage other

automatic actions on protected servers.

1.2.2 Direct sending of E-mail

When a UPS event occurs, the Network Management Card can directly notify up to 4 addresses by e-mail.

(see E-mail Notification and E-mail message settings)

Autres manuels pour Network Management Card

Table des matières

Autres manuels Eaton Carte réseau

Eaton

Eaton Network-M2 Manuel utilisateur

Eaton

Eaton Network Card-MS Manuel utilisateur

Eaton

Eaton DeviceNet Starter Network Adapter D77B-DSNAP Manuel utilisateur

Eaton

Eaton 34003991EN/EB Manuel utilisateur

Eaton

Eaton QSNAP Manuel utilisateur

Eaton

Eaton Network-M3 Manuel utilisateur

Eaton

Eaton Network-M2 Manuel utilisateur

Eaton

Eaton -66103 Manuel utilisateur

Eaton

Eaton POW-R-COMMAND 1000 Manuel utilisateur

Eaton

Eaton Modbus MS Card Manuel utilisateur

Eaton

Eaton Network-MS Manuel utilisateur

Eaton

Eaton Powerware Series Manuel de programmation

Eaton

Eaton Network Card-MS Manuel utilisateur

Eaton

Eaton DeviceNet Product Operated Network Interface Manuel

Eaton

Eaton Power Xpert Meter 2000 Manuel utilisateur

Eaton

Eaton PXGMS Power Xpert Gateway Minislot UPS Manuel utilisateur

Manuels Carte réseau populaires d'autres marques

FirstComm

FirstComm OBiWiFi5G Manuel utilisateur

Sun Microsystems

Sun Microsystems Interface Adapter Manuel utilisateur

TRENDnet

TRENDnet TU2-ETG Manuel utilisateur

YASKAWA

YASKAWA SI-EN3 Manuel utilisateur

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuel utilisateur

Belkin

Belkin F5D7050 Manuel utilisateur

3Com

3Com EtherLink 3C509B Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITX Manuel utilisateur

Cisco

Cisco MC16E Manuel utilisateur

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuel utilisateur

TwinMOS

TwinMOS Booming Manuel utilisateur

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur

National Instruments

National Instruments NI 9234 Manuel utilisateur

Hama

Hama 49276 Manuel utilisateur

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuel d'utilisation

Compaq

Compaq Wireless LAN 100 Manuel utilisateur

Bose

Bose PowerMatch Dante Manuel utilisateur