EasyGates cb24 Manuel utilisateur
simple
setup
g
uide
DIPSWITCHES
After all connections have been made, you are now ready to program the gates. First lets start with
setting the correct dipswitches located at the top centre of the control board.
Whilst programming up the ‘Save’ switch should be set to ‘Off’ during this part of the setup.
If your system has a maglock wired in then dipswitch 2 should be set to ‘On’, if not then set this to
‘Off’.
If you have a double gate system, then switch the 3rd dipswitch to ‘Dual mode’. If just using a single
gate motor then switch it to ‘Single’.
If you have any safety edges wired in, then the 4th dipswitch should be set to ‘NC’. If no safety
edges are connected, then switch this to ‘No’.
The nal dipswitch is for the photocells and this should be switched to ‘NC’.
cb
24
Now all the dipswitches have been set, we can set the dials for ‘Force’, ‘Bipart delay’ and
‘Timer to close’. These dials are located in the centre of the bottom half of the board and are
coloured, Red, White and Blue.
The rst dial is labeled ‘Force’
and should be set to around 40%
power (From min to max)
The second is the ‘Bipart delay’
(white), and should be set to the
same setting as ‘Force’.
The 3rd and nal is the ‘Timer
set to close’, and this should be set to off whilst setting up. Note: After setting up, these dials can be
set to suit the application.
CONFIGURE DIALSCHECK WIRING
Now the dipswitches and dials have
been set, we need to check that
there is a link in the control input
‘P10’, between ‘Stop’ and ‘Com’.
We also need to check the ‘Open
photo’ or ‘Close photo’ connections
are not being used and that they are
linked out.
Now check that the radio module is plugged
in correctly at the top of the board.
Next, connect the 2 battery connections at
the bottom right of the board, and the 24VAC
input (2 yellow wires) at the bottom left of
the board.
You should now have a ‘Power’ LED lit and
a ‘Stop’ LED lit, but you should have no con-
stant red LED’s.
(Before any
of the setup is
started, ensure
Power cables
are discon-
nected to begin
with.)
SETTING THE LIMITS
Now if you put your gates in the close position by releasing them, manually moving them closed and
locking them back in, we can set the limits.
For single gates-
Press the learn limit button once. ‘Set open limit’ LED should be ashing. Hold down the right ‘Gate
one’ button until you reach the fully open position you want for your gate. (if you hold this button
down and it doesn’t do anything or tries to close press the button opposite to open the gates). When
the gate is fully opened to your desired range, press the ‘Learn limits’ button once more.
‘Set close limit’ should be ashing. Use the opposite button that you used for opening and hold down
until the gate is closed. Then nally press the ‘Learn limits’ button again. You should now be ready to
operate your gates. You can test this by pressing ‘Single button’.
For Double gates-
Press the learn limit button once. ‘Set open
limit’ LED should be ashing. Hold down
the right ‘Gate one’ button until you reach
the fully open position you want for your
gate. When gate one is open, hold down the
open button for ‘Gate 2’, directly under-
neath it, until it is open. When the gates are
fully opened to your desired range, press the
‘Learn limits’ button once more.
‘Set close limit’ should be ashing. Use the
opposite buttons that you used for opening
and hold down until the gates are closed.
Then nally press the ‘Learn limits’ button
again. You should now be ready to operate
your gates. You can test this by pressing
‘Single button’.
Disclaimer:
Please note this is just a guide and may vary
according to your setup. Please read all
instructions from the manufacturers before
refering to our guides. Easygates Ltd will not
be held responsible for any damage due to
equipment caused due to poor wiring.
Autres manuels EasyGates Équipements de sécurité
Manuels Équipements de sécurité populaires d'autres marques
Innova
Innova Xtirpa Mode d’emploi
bolle SAFETY
bolle SAFETY B810 Manuel utilisateur
SHENZHEN FANHAI SANJIANG ELECTRONICS
SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manuel utilisateur
Hiltron security
Hiltron security POWER8E Mode d’emploi
Hatco
Hatco B-950P Manuel utilisateur
Sitec
Sitec TX MATIC Manuel utilisateur
