E-con Systems See3CAM 130 Manuel utilisateur

See3CAM_130

Version 1.11

e-con Systems

5/28/2018

e-CAMView Streaming Application

User Manual

Disclaimer

The specifications of See3CAM_130 camera board and instructions on how to

connect this board with PC are provided as reference only and e-con Systems

reserves the right to edit/modify this document without any prior intimation of

whatsoever.

 
2 e-CAMView Streaming Application User Manual 
Contents 
INTRODUCTION TO SEE3CAM_130 4 
PREREQUISITES 4 
DESCRIPTION 5 
USING E-CAMVIEW 7 
DEVICES MENU 7 
OPTIONS MENU 8 
VIDEO CAPTURE FILTER 9 
VIDEO CAPTURE PIN 15 
STILL CAPTURE PIN 15 
FREEZE FRAME 16 
FIT TO WINDOW 16 
CAPTURE MENU 16 
EXTENSION UNIT MENU 17 
SCENE MODES 19 
SPECIAL EFFECT 20 
DE-NOISE 21 
BURST SIZE 22 
AUTO FOCUS 22 
ROI MODE 22 
AUTO EXPOSURE 23 
IHDR 25 
Q-FACTOR 26 
FOCUS WINDOW RECTANGLE 26 
RESTORE DEFAULT 26 
FLIP 27 
STREAM MODE 27 
FACE DETECTION 27 
SMILE DETECTION 27 
FRAME RATE CONTROL 28 
EXPOSURE COMPENSATION 28 
GETTING THE UNIQUE ID OF THE CAMERA 29 
HELP MENU 31 
TROUBLESHOOTING 32 
FAQ 32 
WHAT’S NEXT? 38 

GLOSSARY 39

SUPPORT 40

4 e-CAMView Streaming Application User Manual

Introduction to See3CAM_130

The See3CAM_130 is a 13 Megapixel, color, UVC compliant, USB 3.0 SuperSpeed

camera from e-con Systems, a company with over two decades of experience in

designing, developing, and manufacturing OEM cameras. The See3CAM_130 is the

latest member of the See3CAM family of USB 3.0 SuperSpeed camera products

launched by e-con Systems.

The See3CAM_130 is a 13 Megapixel camera that is based on the 1/3.2” AR1335

CMOS image sensor from Aptina™with Autofocus lens. The See3CAM_130 is also

backward compatible with the USB 2.0 High Speed interface, albeit at lower frame

rates.

The See3CAM_130 is UVC compliant camera and it does not require any drivers to

be installed on the PC. The native UVC drivers of Windows and Linux Operating

Systems (OS) will be compatible with this camera. e-con Systems also provides the

sample application that demonstrates some of the features of this camera.

However, this camera can utilize any DirectShow application such as Skype and so

on.

e-con Systems provides a sample DirectShow application, called e-CAMView, along

with the See3CAM_130 camera. e-CAMView is a typical DirectShow camera

application but customized to demonstrate some of the features of See3CAM_130.

This document describes the special features of sample camera application when it

is used with See3CAM_130.

Prerequisites

The steps to initialize the device with the host computer are as follows:

•Connect the one end of USB 3.0 cable to the USB 3.0 connector provided at the

back of See3CAM_130.

•Connect the other end of USB 3.0 cable to the USB 3.0 host controller on the

computer.

Once connected, the LED light on the device will glow indicating that See3CAM_130

is powered up and ready to use.

As See3CAM_130 is a generic USB Video Class device, Windows will automatically

detect all the drivers and the drivers will be installed. This happens for the first time

and from the second time onwards the device will be detected immediately by the

host PC and will be ready for use.

To view the preview, the e-CAMView application designed for See3CAM_130 must

be installed. Refer to the e-CAMView Streaming Application Installation Manual to

know more on how to install the e-CAMView application.

Description

The See3CAM_130 is a USB 3.0 color camera capable of streaming the resolution

and frame rates as shown in below table.

Table 1: See3CAM_130 Resolution and Frame Rates with FOV Crop

Format

Resolution

Frame Rate

% Crop in FOV

USB 3.0

USB 2.0

Horizontal

Vertical

UYVY

VGA (640 x 480)

120 fps and

60 fps

60 fps and

30 fps

720P (1280 x 720)

60 fps and

30 fps

16 fps and

8 fps

24.14%

960P (1280 x 960)

60 fps and

30 fps

12 fps and

6 fps

1080P (1920 x 1080)

60 fps and

30 fps

8 fps and

4 fps

24.14%

1440P (1920 x 1440)

45 fps and

22.5 fps

6 fps and

3 fps

4K UHD (3840 x

2160)

15 fps and

7.5 fps

2 fps

24.14%

2.8K (2880 x 2160)

20 fps and

10 fps

3 fps

4K Cinema (4096 x

2160)

15 fps and

7.5 fps

2 fps

28.88%

13MP (4208 x 3120)

9 fps and

4.5 fps

1 fps

MJPEG

VGA (640 x 480)

120 fps

720P (1280 x 720)

60 fps

24.14

960P (1280 x 960)

60 fps

1080P (1920 x 1080)

60 fps

24.14

1440P (1920 x 1440)

60 fps

4K UHD (3840 x

2160)

30 fps

24.14

2.8K (2880 x 2160)

30 fps

4K Cinema (4096 x

2160)

30 fps

28.88

13MP (4208 x 3120)

20 fps

For streaming MJPEG, use MainConcept-MJPEG codec package. Find the installer in

the install path C:/Program Files (x86)/e-con_Systems/e-CAMView and install a

demo version of the codec by selecting ignore for demo version while prompted.

Note: The above frame rates are subject to change with lighting of the surroundings,

different renderers and PC configuration. The above table is true only in manual

exposure, when the exposure value is changed above -6 (15.6 milliseconds) there

6 e-CAMView Streaming Application User Manual

will be a drop in the frame rate because the exposure time is more than the frame

time. In auto exposure, maximum frame rate could be achieved with maximum

lighting.

The camera controls of See3CAM_130 are as follows:

•Brightness

•Contrast

•Saturation

•Sharpness

•Gamma

•White Balance (both manual and automatic)

•Gain

•Zoom

•Focus (both manual and automatic)

•Exposure (both manual and automatic)

•Pan

•Tilt

This document explains the following sections:

•Selecting the supported preview resolutions.

•Selecting the still image resolution.

•Capturing still images.

•Using supported controls.

•Getting the Unique ID of the camera.

The Field of View (FOV) of See3CAM_130 is shown below.

Figure 1: FOV of See3CAM_130

Using e-CAMView

This section describes how to use the e-CAMView application.

To launch the e-CAMView video streaming and capture application, click Start > All

Programs > e-con Systems > e-CAMView.

This version of e-CAMView is provided with a set of features that can be used to

attain the full functionality of See3CAM_130. The Menu bar at the top contains

menu items and the Status bar at the bottom shows related information. When the

application is running, the current preview resolution and the frame rate are

displayed in the Status bar as shown below.

Figure 2: Application Launch Appearance

The following sections describe each of the menu items in detail.

Devices Menu

You can click the Devices menu to view the currently connected video devices to

host PC and you can select any video devices attached to the computer. A check

mark is placed before the device indicating the video device which is currently

streaming. By default, the See3CAM_130 device will be indicated by the name

See3CAM_130. The See3CAM_130 camera being listed in the Devices menu is

shown below.

8 e-CAMView Streaming Application User Manual

Figure 3: Enumerated Devices List

In case any other video device such as on-board webcam is connected, e-CAMView

will list down those video capture devices and you can switch between the available

video capture devices, by selecting the respective device.

Note: There is no audio capture source available with the See3CAM_130 camera.

Options Menu

You can click the Options menu to select the various preview, image resolutions and

the controls that are supported by See3CAM_130. When you click the Options

menu, you can view the options listed in the Options menu as shown below.

Figure 4: Options Menu

From this Options menu, you can select the following options:

•Video Capture Filter - to change brightness and exposure values.

•Video Capture Pin - to select various video preview resolutions supported by the

device.

•Still Capture Pin - to select various still image resolutions supported by the

device.

•Freeze Frame - to pause the live preview.

•Fit To Window - to resize the preview to e-CAMView window.

The details of each of these options are described below.

Video Capture Filter

You can click the Video Capture Filter option of the Options menu to configure some

of the camera parameters of See3CAM_130 camera. When you click the Video Proc

Amp tab in the Properties dialog box, you can view the controls that are available in

the Properties dialog box as shown below.

Autres manuels pour See3CAM 130

Table des matières

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur

e-con Systems See3CAM 130 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques