Dynalink RTA210 Manuel utilisateur
Quick Setup Guide
RTA210
ADSL Router
Important
This Guide is intended to get you started quickly.
We have pre-configured the router for the New Zealand
AD L network. All you need to do is to follow through the
steps we describe here.
This Guide should be read in conjunction with the ADSL
Router User Manual. This is provided as a PDF file on the
Utility CDROM.
Note: the ADSL Router User Manual was written for
international users. New Zealand users should ignore
relevant material on page 9 and all sections of hapter 3,
except Section 3.3 PPPoA+NAT mode. PPPoA+NAT is the
only mode of operation currently supported in New
Zealand.
Advanced users who have other setup preferences should
refer to the ADSL Router User Manual. There is a table in
ection 3 of this Guide is to assist you in locating the
relevant material.
Contents inside this box:
RTA210 router
Power adapter 12VDC 1A
AD L line cord for New Zealand
RJ-45 Ethernet cable
Utility CDROM (User Manual included)
Default Configuration for New Zealand
We have pre-configured this router to the following settings. If you accept the
settings, please move on to ection 2 "Installing the Router".
Router IP address 192.168.1.1
ubnet mask 255.255.255.0
VPI 0 (do not change)
VCI 100 (do not change)
Encapsulation PPPoA VC-MUX (do not change)
Operating mode G.dmt (do not change)
NAT enabled (do not change)
WAN IP dynamic
DHCP off
DN relay off
Router configuration and management:
User name admin
Password private
Telnet password private
Users must not change VPI, VCI, Encapsulation and Operating Mode settings.
Advanced users who have other setup preferences should refer to the AD L
Router User Manual on the provided CDROM.
Installing the Router
IMPORTANT- efore you start
Make sure your computer has these installed:
Network interface card (NIC)
TCP/IP protocol.
Other than attaching to a host computer the router can be connected to an uplink
port of a network hub. If the hub has no uplink port available, a cross-over
Ethernet cable must be used. This cable is not provided.
A web browser is required to enter your Internet account user name & password.
Make sure your web browser is Internet Explorer 5.0/Netscape 6 or better. Install
either Explorer 5.5 or Netscape 6 from the provided CDROM if your computer
does not have a suitable browser.
Remember to obtain these from your I P:
Login user name and password
Public IP address (only if you subscribe for static IP)
DN server IP.
1
2
ADSL Router Quick et-up Guide
STEP 1 CONNECT IT UP
For a step-by-step guide refer to Page 5 Chapter 2 Hardware Description &
Installation of the AD L Router User Manual on CDRom.
Connect the DSL port of the router into your AD L jackpoint (telephone wall
socket) with the provided line cord. Never connect through a microfilter.
Connect the LAN port of the router to the Ethernet port of your computer (or
uplink port of a network hub) with the Ethernet cable provided.
Connect the 12V DC power adapter to the PWR jack of router, and plug the
adapter into a mains power outlet. witch on the router.
Make sure the LAN light on the front panel of the router is on. Otherwise it
indicates a problem with the Ethernet connection.
STEP 2 PREPARE YOUR COMPUTER
A detailed step-by-step guide for Windows 98/NT4.0/2000 can be found on
Page 17 hapter 4 Setting up P on the LAN of the ADSL Router User Manaul
on DRom.
Assign an IP address to your computer. Use 192.168.1.x (x is any number of your
choice between 2 and 254) and subnet mask 255.255.255.0. pecify gateway
as 192.168.1.1 and enter DN server IP.
For Windows 95/98/ME:
From Control Panel, double click
Network.
croll down to highlight TCP/IP
(your network card). Click on
Properties.
elect DNS Configuration tab, click
Enable DNS. Type in any name for
host. Enter your I P’s DN address.
Click Add. A second DN address
(if specified) can be added in a
similar way.
If you are unsure what your I P’s
DN address is, you may pick one
of the following addresses until
your I P’s DN is known:
150.199.1.11
128.206.2.252
131.151.254.243
Click OK & then OK to finish. ystem
may ask for the Windows CDROM
and then will ask to restart. Answer
Yes to restart the computer.
elect IP Address tab. pecify
192.168.1.x (x is any number of your
choice between 2 and 254). This is the
IP address assigned to your computer.
Subnet Mask is 255.255.255.0.
elect Gateway tab. Enter the router’s
IP address 192.168.1.1.
Click Add
ADSL Router Quick et-up Guide
For Windows XP/2000:
From Control Panel - Network Connections. Open Local Area Connections
and click Properties. Double click Internet Protocol (TCP/IP). elect Use
the following IP address.
Enter 192.168.1.x (x is any number
between 2 and 254). This is the IP
address assigned to your computer.
Subnet Mask is 255.255.255.0.
Enter the Router’s IP 192.168.1.1
as Default gateway.
elect Use the following DNS
server addresses. Enter your I P’s
DN address. A second DN
address (if specified) can be added.
If you are unsure what your I P’s
DN address is, you may pick one
of the following addresses until
your I P’s DN is known:
150.199.1.11
128.206.2.252
131.151.254.243
Click OK to finish
STEP 3 USE WE ROWSER TO CONFIGURE ROUTER
tart your web browser and
type the router’s IP address
http://192.168.1.1.
You will be prompted to enter
User Name and Password. By
default, user name is admin
and password is private.
ee Q1 in Section 6 -
Troubleshooting if you
cannot get this screen.
ADSL Router Quick et-up Guide
STEP 4 ENTER INTERNET ACCOUNT USER NAME AND PASSWORD
Go to Configuration > WAN > ATM PVC > Setup ATM PVC. The pre-configured
"MyConnection" PVC Interface will appear.
croll down to check that Encapsulation Type is PPPoA & VC_MUX. Locate
the PPP0A Configuration section. Edit the User Name and Password fields
using the user name and password supplied by your I P. Click Submit.
STEP 5 SAVE CONFIGURATION AND CHECK IF THE ROUTER IS ONLINE
Go to Tool > Save Configuration. Click on Save. Next go to Tool > Reset Router.
Make sure the "Reset to factory default settings" box is NOT ticked. Click
Restart.
CAU ION - if you reset to factory default the configuration for New Zealand
and everything you entered will be lost. It is then necessary to follow Section
5 of this Guide to reconfigure the router.
When the router restarts the D L light on the front panel turns solid, normally
within one minute. This indicates the router has already established a link to
the telephone exchange and will authenticate using your Internet account
information. ubject to successful authentication you are online. The D L
light blinks as data gets through.
If nothing happens return to tep 4. croll down to the bottom of the page
and click Connect to connect immediately. oon after you should observe
data getting through.
Any time you want to check that the router is online, go to Status > Connection
> ATMPVC. Under Status, it should show Active. The public IP assigned by
your I P is displayed under NAT IP. The picture below shows the router has
been assigned 210.86.78.50. If you cannot go online see Q2 in Section 6 -
Troubleshooting.
DHCP:
Configure PC to get IP from DHCP Page 32 ection 4.2
Enable DHCP Page 43 ection 6.2.2
how DHCP table Page 70 ection 6.5.6
Use the Web Configuration Manager Page 39 Chapter 5
Change the private IP address of the router Page 42 ection 6.2.1
Enable routing RIP v1/v2 Page 45 ection 6.2.3
Modify I P login name or password Page 48 ection 6.3.2
Change from Dynamic to tatic WAN IP Page 48 ection 6.3.2
Modify user name or password Page 53 ection 6.4.1
for router management
et static routing Page 54 ection 6.4.2
et IP packet filtering Page 57 ection 6.4.3
et virtual server (NAPT); Page 60 ection 6.4.4
Run applications such as Netmeeting,
IRC, Quake, FTP/Mail/Web server
Get connection status Page 62 ection 6.5
Get connection statistics Page 67 ection 6.5.4
how routing table Page 69 ection 6.5.5
Upgrade router via software Page 72 ection 6.6.2
Other material for advanced users
Refer to these sections of the AD L Router User Manual for:
3
ADSL Router Quick et-up Guide
Indicator lights
There are four green indicats on the front panel of the router. All lights will come
on indicating self-test in progress every time the router is switched on.
Indicator Function Description
PWR Power Off - No power.
On - Power is on.
DIAG Diagnosis Off - elf-test OK.
Blinking – Upgrade in progress.
On - elf-test or upgrade failed.
LAN Network Link Off - Ethernet not present.
Blinking – Data going through Ethernet port.
On - Ethernet is present.
D L Link tatus Off - Handshaking/training in progress.
Blinking - Data going through AD L port.
On - AD L link is up.
4
Reconfigure router after reset to factory default
If it happens that the router has been reset to factory default, you must restore
the New Zealand configuration to connect. Go to Configuration > WAN > ATM
PVC > Setup ATM PVC:
5
Autres manuels pour RTA210
1
Table des matières
Autres manuels Dynalink Routeur réseau
Dynalink
Dynalink RTA1335 Manuel utilisateur
Dynalink
Dynalink RTA210 Manuel utilisateur
Dynalink
Dynalink RTA300 Manuel utilisateur
Dynalink
Dynalink RTA1046VW Manuel utilisateur
Dynalink
Dynalink RTA1046 Manuel utilisateur
Dynalink
Dynalink RTA220 Manuel utilisateur
Dynalink
Dynalink RTA1030W Manuel utilisateur
Dynalink
Dynalink RTA230 Manuel utilisateur
Dynalink
Dynalink RTA1046VW Manuel utilisateur
Dynalink
Dynalink DL-WME38 Guide d'installation
Dynalink
Dynalink DL-WRX36 Manuel utilisateur
Dynalink
Dynalink AXE10200 Manuel utilisateur
Dynalink
Dynalink RTA020 Manuel utilisateur
Dynalink
Dynalink RTA1335 Manuel utilisateur
Dynalink
Dynalink RTA1335 Manuel utilisateur
Dynalink
Dynalink 56K e-modem II Manuel utilisateur
Dynalink
Dynalink RTA770 Manuel utilisateur
Dynalink
Dynalink RTA1320 Manuel utilisateur
Dynalink
Dynalink DL-WRX36 Manuel utilisateur
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité