Dyna-Glo KFA80C Manuel utilisateur

CONSUMER : Retain this manual for future reference.

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 877-447-4768 8:30 a.m. - 4:30 pm CST, Monday - Friday.

or email us at [email protected]

INDOOR/OUTDOOR PRODUCTS

KEROSENE PORTABLE

FORCED AIR HEATERS

“USER’S MANUAL AND

OPERATING INSTRUCTIONS”

Before the first use of this heater, please read this USER’S MANUAL very

carefully. This USER’S MANUAL has been designed to instruct you as to

the proper manner in which to assemble, maintain, store, and most

importantly, how to operate the heater in a safe and efficient manner.

Please keep this manual for future reference.

COMPLIES WITH UL733 AND

ANSI A10.10-1998

CAN/CSA/B140.0-03 AND CSA

B140.8-1967

MODEL : KFA80C, KFA135C, KFA220C

IMKFAC-HDA

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

DANGER:IMPROPER USEOF THIS HEATER CAN RESULT IN SERIOUS INJURY OR DEATH

FROM BURNS, FIRE, EXPLOSION, ELECTRICALSHOCK AND/OR CARBON

MONOXIDEPOISONING.

WARNINGS:

1. RISK OF INDOOR AIR POLLUTION!

•Usethis heater only in well ventilated areas. Provide at least a three-square foot(2,800 sq. cm.)

opening of fresh outside air for each 100,000 BTU/hr. of heater rating.

•People with breathing problems should consult a physician beforeusing the heater.

•Carbon monoxide poisoning: Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness

and/or nausea. If you have these signs, the heater may notbeworking properly.

Get fresh air at once!Have the heater serviced. Some people are more affected by carbon monoxide than others.

These includepregnant women, persons with heart or lung disease or anemia, thoseunder the influence of alcohol, or

those at high altitudes.

•Never use this heater in living or sleeping areas.

2. RISK OFBURNS/FIRE/EXPLOSION!

•NEVER use any fuel other than 1-K kerosene, #1/#2 disel/fuel oil, JET A or JP-8 fuels in this heater.

•NEVER use fuel suchasgasoline, benzene, paint thinners or otheroil compounds in this heater.

(RISK OF FIRE OR EXPLOSION)

•NEVER use thisheater where flammable vapors may be present.

•NEVER refill the heaters fuel tank while heater is operating or is still hot.

Minimum Clearances: Outlet: 8 feet (250cm) /Sides, top and rear: 4 feet (125cm)

•NEVER block airinlet (rear) or air outlet (front) of heater.

•NEVER use duct work in front orbehind of heater.

•NEVER move, handle, service a hot, operating or plugged in heater.

•NEVER transport heater with fuel init’s tank.

•When used withanoptional thermostat or if equipped with a thermostat heater may start at any time.

•ALWAYSlocate heaterona stable and level surface.

•ALWAYSkeep children andanimalsaway from heater.

•Bulk fuel storage should be a minimum of 25 ft. from heaters, torches, portable generators or other sources of ignition.

All fuel storage should be in accordance with federal, state or local authorities having jurisdiction.

3. RISK OF ELECTRIC SHOCK!

•Use only the electrical power (voltage and frequency) specified on the model plate of the heater.

•Use only a three-prong, grounded outlet and extension cord.

•ALWAYSinstall the heater so that it is not directlyexposed to water spray, rain, dripping water or wind.

•ALWAYSunplug the heater when not in use.

PROPOSITION 65 WARNING: Fuels used in gas, wood-burning or oil fired appliances, and the

products of combustion of such fuels, contain chemicals known to the State of California to cause cancer,

birth defects and other reproductive harm.

MASSACHUSETTS RESIDENTS: Massachusetts state law prohibits the use of this heater in any

building which is used in whole or in part for human habitation. Use of this heating device in

Massachusetts requires local fire dept. permit (M.E.L.C. 148, Section 10A.)

CANADIAN RESIDENTS: Use of this heater shall be in accordance with authorities having

jurisdiction and CSA Standard B139.

NEW YORK CITY RESIDENTS: For use only at construction sites in accordance with applicable NYC

codes

under NYCFD certificate of approval # 5034 and 5037.

CAUTION :Hot while in operation. Do not touch. Keep children,

clothing and combustibles away from heater.

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

ITEM PAGE #

1EDIUGYTEFAS-SNOITUACERP

2NOITCUDORTNI.1

2SERUTAEF.2

4YLBMESSADNAGNIKCAPNU.3

6FUELS.4

7NGISEDRETAEHFOWEIVREVO.5

8RETAEHRUOYGNILEUF.6

8NOITAREPO.7

9RETAEHRUOYFOEGAROTSMRETGNOL.8

01ECNANETNIAM.9

41ESUFGNICALPER.01

51EDIUGGNITOOHSELBUORT.11

61MARGAIDGNIRIW.21

71SNOITACIFICEPS.31

18&21GNIWARDSTRAPDEDOLPXE.41

19,20&22,23TSILSTRAP.51

1. INTRODUCTION

Please read this USER’S MANUAL carefully. It will show you how to assemble, maintain, and operate the

heater safely and efficiently to obtain full benefits from its many built-in features.

2. FEATURES

CONTENTS OF USER’S MANUAL

Fan Guard

BTU Control Switch

Cord Wrap

Pressure Gauge

Fuel Gauge

Fuel Cap

Front Guard

Hot Air Outlet

Lower Shell

Fuel Tank

Side Cover

Lamp

Thermostot Knob

Power/Reset Switch

Power Cord

(Piggy Back)

Upper Shell

Handle

Figure 1. KFA80C MODEL

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

Figure 2. KFA135C MODEL

Figure 3. KFA220C MODEL

Hot Air Outlet

Shell Lower

Fuel Gauge

Fuel Cap

Side Cover

Lamp

Thermostot Knob

Room Temp. Display

Power/Reset Switch

10” Flat Free Wheel

Hot Air Outlet

Shell Lower

Fuel Gauge

Fuel Cap

Side Cover

Thermostot Knob

Lamp

Room Temp. Display

Power/Reset Switch

10” Flat Free Wheel

Front Handle

Rear Handle

Upper Shell

Front Handle

Upper Shell

Cord Wrap

BTU Control Switch

Pressure Gauge

Fan Guard

Power Cord

(Piggy Back)

Fuel Drain Bolt

BTU Control Switch

Pressure Gauge

Fan Guard

Power Cord

Fuel Drain Bolt

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

3. UNPACKING AND ASSEMBLY

1. REMOVE THE HEATER AND ALL PACKING MATERIALS FROM THE BOX. (Fig. 4 and 5)

NOTE : Save the shipping carton and packing materials for future storage.

Figure 4. KFA80C MODEL

KFA80C KFA135C KFA220C

Wheel Support Frame No Yes Yes

Wheel No Yes Yes

seYseYoNThreaded Axle

seYseYoNFront Handle

Rear Handle seYseYoN

oNoNseYeldnaH

seYseYseYparWdroC

Hardware kit : HW-KFA1016 No Yes Yes

Cap Nuts S

Hardware Kit : HW-KFA1016

(10" Flat Free)

Wheels

Cord Wraps

Screws Flange Screws

Nuts Bushings Cap Nuts L

Axle

Rear Handle

Wheel Support Frame

Front Handle

Handle Cord Wraps

Figure 5. KFA135C/ KFA220C MODELS

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

2. ASSEMBLY

For KFA80C Model only

(Assembly time for this product is 3minutes)

For KFA135C/220C Models only (Assembly time for this product is 10 minutes)

Tools Required

•Medium Phillips Screwdriver.

1) Lift front guard for arrow direction and

make sure that guard’s wedged portion

fits into the slit hole on the upper housing.

Tools Required

• Medium Phillips Screwdriver.

• 3/4 inch socket or adjustable wrench

Assembling Handle & Wheel and Cord Wrap

1) Slide threaded axle through the rear section of the wheel support frane.

2) Slide one axle bushing on to each side of the axle. Slide one wheel on to each side of the axle.

Attach one cap nut on to each side of the threaded axle and tighten well.

3) Place heater on wheel support frame. Align the holes on fuel tank flange with holes on wheel support frame.

4) Position the Handles on top of fuel tank flange.

Insert screws through handles, fuel tank flange and wheel support frames as shown in Figure 8 and

attach nut finger tight after each screw is inserted.

5) Align the hole on the handles with the mounting hole on the Cord Wrap.

Insert Screws through Cord Wrap, handles and attach nut finger tight after each screw is inserted.

6) After all screws are inserted, tighten nuts firmly.

2) Remove the pre-assembled screws on the

shell upper and side cover.

3) Align the holesin the upper housing with

two mounting holes on the handle as

shown in Figure 6.

4) Secure handle with the screws removed.

5) Insert card wrap intothe rectangle holeson the

supportor and align the hole on the cord wrap with

the mounting hole on the side cover as shown in

Figure 6.

6) Secure cord wrap with the screws removed.

Figure 6. Assembling Handle & Cord Wrap

Handle Screw

Front Guard

Wedged Portion

Slit Hole

Side Cover

Cord Wrap

Screw

Shell Upper

Remove Screws

Remove

Screws

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

CAUTION : DO NOT OPERATE heater without support frame assembled to tank.

NOTE : Heater should be inspected before each use, and at least annually by a qualified service person.

Cap Nut L

Wheel Wheel Bushing

Threaded Axle

Rear Handle

Air Inlet

Cord Wrap

Cap Nut S

Nut

Hot Air Outlet

Screw

Flange Screw

Front Handle

Wheel Support Frame

Flange

Fuel Tank

4. FUELS

For optimal performance of this heater, it is strongly suggested that 1-K kerosene be used. 1-K kerosene has

been refined to virtually eliminate contaminants, such as sulpher. Which can cause a rotten egg odor during

is not available. Be advised that these fuels do not burn as clean as 1-K kerosene, and care should be taken to

KEROSENE SHOULD ONLY BE STORED IN A BLUE CONTAINER THAT IS CLEARLY

MARKED “KEROSENE”. NEVER STORE KEROSENE IN A RED CONTAINER.

Red containers are associated with gasoline.

NEVER store kerosene in the living space. Kerosene should be stored in a well ventilated place outside the

living area.

NEVER

NEVER use fuel such as gasoline, benzene, alcohol, white gas, camp stove fuel, paint thinners, or other oil

compounds in this heater. These are volatile fuels that can cause an explosion or uncontrolled flames.

NEVER store kerosene in direct sunlight or near a source of heat.

NEVER use kerosene that has been stored from one season to the next. Kerosene deteriorates over time.

“OLD KEROSENE” WILL NOT BUR N PROPERLY IN THIS HEATER.

the operation of the heater. However, #1/#2 diesel/fuel oil, JET A or JP-8 fuels may also be used if 1-K kerosene

provide more fresh air ventilation to accomodate any added contaminants that may be added to the heated space.

#2 diesel/fuel oil heavier than 1-K kerosene in extreme cold temperatures without nontoxic anti-icer additives

will not ignite properly.

use any fuel other than 1-K kerosene (#1/#2 diesel/fuel oil, JET A or JP-8 fuels are acceptable substitutes)

Figure 7. Assembling Handle, Wheel and Cord wrap

5. OVERVIEW OF HEATERS DESIGN

Fuel System : This heater is equipped with an electric

air pump that forces air through the air

line connected to the fuel intake and then

through a nozzle in the burner head.

When the air passes in front of the fuel

intake it causes fuel to rise from the tank

and into the burner nozzle. This fuel and

air mixture is then sprayed into the

combustion chamber in a fine mist.

“Sure Fire Ignition” : The electronic ignitor sends voltage to a specially designed spark plug.

The spark plug ignites the fuel and air mixture described above.

The Air System : The heavy duty motor turns a fan that forces air into and around the combustion chamber.

Here the air is heated and then forced out the front of the heater.

The Safety System :

A. Temperature Limit Control : This heater is equipped with a Temperature Limit Control designed to turn

off the heater should the internal temperature rise to an unsafe level. If this

device activates and turns your heater off it may require service.

Once the temperature falls below the reset temperature you will be able to start your heater.

B. Electrical System Protection : This heaters electrical system is protected by a fuse mounted to the PCB

assembly that protects it and other electrical components from damage.

If your heater fails to operate check this fuse first and replace as needed.

C. Flame-Out Sensor : Utilizes a photocell to monitor the flame in burn chamber during normal operation.

It will cause the heater to shut-off should the burner flame extinguish.

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

Internal Shut-Off Temp. Reset Temperature

MODELS Plus/Minus 10 Degrees Plus/Minus 10 Degrees

KFA80C 158˚F/70˚C104˚F/40˚C

KFA135C 158˚F/70˚C104˚F/40˚C

KFA220C 194˚F/90˚C140˚F/60˚C

FUSE TYPE: All Models 125 volt / 8 amps

6. FUELING YOUR HEATER

NEVER FILL THE HEATER FUEL TANKIN THE LIVING SPACE: FILL THE TANK OUTDOORS.

DO NOT OVERFILL YOUR HEATER AND BE SURE HEATER IS LEVELED.

IMPORTANTNOTICEREGARDING FIRSTIGNITION OF HEATER :

The first time you light the heater, it should be done outdoors. This allows the oils, etc. used in

manufacturing the heater to burn off outside.

WARNING!! : NEVER REFILL HEATER FUEL TANKWHEN HEATER IS OPERATINGOR STILL HOT.

7. OPERATION

A.) VENTILATION

RISK OF INDOOR AIR POLLUTION/USE HEATER ONLY IN WELL VENTILATED AREAS.

Provide a fresh air opening of at least three square feet (2,800 sq. cm) for each 100,000 BTU/Hr.

rating. Provide extra fresh air if more heaters are being used.

Example : A KFA220C heater requires one of the following:

• a two-car garage door raised six inches (15.24 cm)

• a single-car garage door raised nine inches (22.86 cm)

• two, thirty-inch (76.20 cm) windows raised fifteen inches (38.1 cm)

B.) OPERATION

TO START HEATER

1. Fill fuel tank with fuel.

NOTE : Kerosene is recommended when the temperature drops below 0℉(-18℃) to prevent ignition

delay or failure.

2. Attach fuel cap.

3. Plug power cord of heater into three-prong, grounded extension cord. Extension cord must be at

least six feet long.

Extension Cord Wire Size Requirements

• 6 to 100 feet (1.8 to 30.5 meters) long, use 16 AWG conductor.

• 101 to 200 feet (30.8 to 61 meters) long, use 14 AWG conductor.

4. Turn “THERMOSTAT CONTROL knob” to desired setting (setting range : 40˚F ~ 110˚F)

5. Push “BTU control Switch” to “High” level.(See Figure 8.)

6. Push Power Switch to “ON” position, Power lndicator Lamp will light and heater will start.

7. After startup, push “BTU control switch” to desired level “High or Low”

NOTE : Room Temperature display explanations are as follows: (KFA135C/220C Models only)

•When the room temperature is less 0℉, the LED display will show “Lo”

When room temp is between 0℉ and 99℉, the number shown on the display is the current

room temperature.

When room temperature is greater than 99℉, the LED display will show “Hi”

•

•If heater does not start, the thermostat setting may be too low, turn “thermostat Control Knob” to

higher position to start heater. If heater still does not start, turn power switch to “OFF” and then to

“ON” position. If heater still does not start, see Troubleshootiong Guide on page15.

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

NOTE : User can select to operate the heater on two different BTU levels(High or Low).

To stabilize heater and prevent ignition delay, select BTU level after turning the heater on, or

while it is in operation by pushing the BTU control switch. If the heater started at low BTU level

in cold weather or low fuel tank, ignition failure can occur.

NOTE : In cold weather, ignition may be improved by holding a finger over the end of the relief valve or

block fanguard in half with newspaper etc. until the heater ignites.

NOTICE : The major electrical components of this heater are protected by a safety fuse mounted to the PCBboard.

If your heater fails to start, check this fusefirst and replace as necessary. You should also check your

power source to insure that proper voltage and frequency are being supplied to the heater.

TO STOP HEATER

1. Turn switch to “OFF” and unplug power cord.

TO RESTART HEATER

1.Wait 10 seconds after stopping heater.

2. Repeat steps under to start heater.

PIGGYBACK POWER CORD

WARNING : SHOCK HAZARD!

8. LONG TERM STORAGE OF YOUR HEATER

FUEL TANK DRAIN

1. Drain fuel tank through fuel cap opening.

(For KFA80C Model Only)

2. Remove fuel drain bolt from rear bottom side of fuel tank using 3/4” socket or adjustable wrench and drain.

(For KFA135C /220C Models Only. See Figure 10)

3. Using a small amount of kerosene, swirl and rinse the inside of the tank.

NEVER mix water with the kerosene as it will cause rust inside the tank.

Pour the kerosene out making sure that you remove it all.

IMPORTANT : Do not store kerosene over summer months for use during next heating season.

Using old fuel could damage heater.

4. Reinstall fuel cap. Properly dispose of old and dirty fuel.

(For KFA80C Models Only)

5. Reinstall fuel drain bolt to Fuel tank and tighten firmly using 3/4” socket

or adjustable wrench. (For KFA135C /220C Models Only. See Figure 10)

IMPORTANT : Before reinstalling the fuel drain bolt, make sure the

seal is on the bolt. If the seal is not used the bolt cannot

be installed correctly and the fuel tank will leak.

6. Store heater in dry well ventilated area. Make sure storage place is free

of dust and corrosive fumes.

7. Store the heater in the original box with the original packing material and keep the USER’SMANUAL

with the heater.

•Always cover electric outlet when not in use.

•Don’t plug and use a appliance more than 120V/60Hz 5A

current in this outlet.

Figure 10. Fuel Drain Bolt

Fuel Drain Bolt

Seal

revoC

Figure 9. PiggyBack Power Cord

Outlet

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

Figure 8. Controls for All Models

Power Switch

KFA80C Model KFA135C/220C Models

Room Temp. Display

Power Switch

Thermostat

Control Knob

Thermostat

Control Knob

Lamp Lamp

Fan Guard

Btu Control Switch

Push to"HIGH"

Push to"LOW" Relief Valve

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dyna-Glo Chauffage

Dyna-Glo

Dyna-Glo KFA50H Manuel

Dyna-Glo

Dyna-Glo BF10PTDG/PMDG Manuel utilisateur

Dyna-Glo

Dyna-Glo WORKHORSE Series Manuel

Dyna-Glo

Dyna-Glo PROFESSIONAL OHIR18LV Instructions de montage

Dyna-Glo

Dyna-Glo SF70DGD Manuel utilisateur

Dyna-Glo

Dyna-Glo BF10PTDG-4 Manuel utilisateur

Dyna-Glo

Dyna-Glo RMC-LPC25DG Manuel du propriétaire

Dyna-Glo

Dyna-Glo WK11C8 Manuel utilisateur

Dyna-Glo

Dyna-Glo KFA50WH Manuel

Dyna-Glo

Dyna-Glo DELUX LPFA43DGD Manuel

Dyna-Glo

Dyna-Glo RMC-KFA50DGP Manuel

Dyna-Glo

Dyna-Glo BFSS10LPT-4P Manuel utilisateur

Dyna-Glo

Dyna-Glo WORKHORSE FA43 Series Manuel

Dyna-Glo

Dyna-Glo Delux KFA650DGD Manuel

Dyna-Glo

Dyna-Glo RMC-55R7 Manuel utilisateur

Dyna-Glo

Dyna-Glo EG4800DGP Instructions d'installation et d'utilisation

Dyna-Glo

Dyna-Glo KFA80H Manuel

Dyna-Glo

Dyna-Glo Delux KFA50DGD Manuel

Dyna-Glo

Dyna-Glo EG5000DGC Instructions d'installation et d'utilisation

Dyna-Glo

Dyna-Glo LPC25 Series Manuel du propriétaire

Dyna-Glo

Dyna-Glo EG4000DG Instructions d'installation et d'utilisation

Dyna-Glo

Dyna-Glo WK95C6C Manuel utilisateur

Dyna-Glo

Dyna-Glo HA1360RH Manuel

Dyna-Glo

Dyna-Glo RMC-KFA70TDGP Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur