Dymo LabelWriter DUO Manuel utilisateur

LabelWriter Duo

www.dymo.com

Quick Start

LW duo_QSC.indd 1 23-01-2006 14:07:22

Follow these steps to install the LabelWriter printer and print your first label.

1. Unpacking your LabelWriter Printer

NOTE For Windows, do not plug the printer into your computer until asked to do so during the

software installation.

1Unpack your printer and save the packing materials.

2Make sure you have all the items shown in Figure 1.

Your LabelWriter printer is a direct thermal printer and does not use toner, ink cartridges, or a ribbon.

Instead, it uses heat from a thermal print head to print on specially treated labels. Labels are the only

supplies you will ever need to buy.

QSG

SwitchingAdapter

SHOCKHAZARD

RISKOF ELECTRIC

SHOCK

DRYL

OCA

TIONUSE ONLY

NON-SERVICEABLEP

ART

SINSIDE.

FORUSE WITH ITE ONLY

ENDAST FOR KONTORSMASKINER.

CAUTION

Testedtocomply

withFCC

standards

FORHOMEOR

OFFICEUSE

I.T.E

.POWE

RSUPPLY

ModelNo.:TESA2-2401000

U.S.P/N:90819

EuropeP/N:924883

INPUT:100-240V-50/60HzMax0.64A

OUTPUT

:24V---0-1.0A

MADEIN CHINA

LISTED

15WM

198850

ULUL

N10926

Figure 1

Power adapter

LabelWriter printer

CD-ROM

Roll of labels

Power cable

Quick Start Guide

USB cable

D1 tape

cassette

Become familiar with the printer’s major components. See Figure 2.

LabelWriter Printer Features

The form-feed button on the front of the printer is used to advance a single label. The label eject button

is used to remove labels from the printer. The tape tray release button opens the tape tray to insert or

remove a tape cassette.

The LED status light allows you to visually determine the current state of the printer:

•Solid blue - power is on and the printer is ready.

•Flashing blue - labels are not loaded properly or label spool is empty.

Figure 2

Form-feed

Label feed path

and tear bar

USB

connector

DC power

connector

button and LED

Tape tray

cover

Label roll

Top

Platen

release

Label eject

button

release button

Tape feed

path

2. Installing the Software

To install the software on a Windows system

NOTE Do not connect the printer to your computer until instructed to do so during the software

installation.

1Insert the LabelWriter CD into your CD-ROM drive.

After a few seconds, the installation screen appears.

If the installation screen does not appear:

a. Click Start and then Run on the Windows taskbar. The Run dialog box appears.

b. Enter D:\install.exe (where D is the letter assigned to the CD-ROM drive) and click OK.

2Select the language version you wish to install and then follow the on-screen instructions.

To install the software on a Macintosh system

1Insert the DYMO LabelWriter CD into the CD-ROM drive.

After a few seconds, the DYMO Label Software Installer icon appears. See

Figure 3.

2Double-click the Installer icon and then follow the on-screen instructions.

DYMO Label

Software Installer

Figure 3

3. Connecting your LabelWriter Printer

At some point during the software installation, you will be asked

to connect your LabelWriter printer to the USB port.

NOTE For Windows, do not connect the printer to your

computer until instructed to do so during the software installation.

To connect the power

1Plug the power cord into the power adapter. See Figure 4.

2Plug the power adapter into the power connector on the back

of the printer. See Figure 5. Make sure to push the plug in

completely.

3Plug the other end of the power cord into a power outlet.

To connect the USB cable

1Plug the USB cable into the USB port on the back of the

printer. See Figure 5.

2When prompted during the software installation, plug the USB

cable into an available USB port on your computer. See

Figure 6.

SwitchingAdapter

SHOCKHAZARD

RISKOFELECTRIC SHOCK

DRYLOCATIONUSE ONLY.

NON-SERVICEABLEPARTSINSIDE.

FORUSEWITH ITE ONLY.

ENDASTFOR KONTORSMASKINER.

CAUTION

Testedtocomply

withFCCstandards

FORHOMEOR

OFFICEUSE

I.T.E.POWERSUPPLY

ModelNo.:TESA2-2401000

U.S.P/N: 90819

EuropeP/N: 924883

INPUT:100-240V-50/60HzMax0.64A

OUTPUT:24V---0-1.0A

MADEINCHINA

LISTED

15WM

E198850

ULUL

N10926

Power Adapter

Power Cord

Figure 4

Figure 5

Power

USB

Figure 6

4. Loading Labels

The printer uses two types of labels: die-cut paper labels and D1 tape labels.

To load die-cut labels

1Press the form-feed button to eject the labels that protected the printer during shipment.

2Open the top cover and remove the label spool.

3Hold the spool spindle in your left hand and place the

label roll on the spindle so that the labels feed from

underneath.

4Place the spool guide on the right side of the spool and

adjust it to fit snugly against the roll. See Figure 7.

5Insert the label spool into the slots in the printer cover.

6Cut the first label in half so that you have a clean edge and insert

the label into the label feed slot. See Figure 8.

The printer feeds the labels, stopping at the beginning of the first

label. If the printer stops without feeding the label, make sure the

label is fully inserted and then press the form-feed button.

7Close the top cover.

Figure 7

Figure 8

To load the D1 tape cassette

1Press the button on the front of the printer to open the

tape cassette tray.

2Set the cassette switch for the size of the tape cassette

that you are inserting. See Figure 9. A notch in the

cassette fits over the switch when the cassette is in the

correct position.

NOTE The first time you use the printer, remove the

protective cardboard insert from between the print head and

pinch roller. See Figure 9.

3Make sure the tape and ribbon are taut across the

mouth of the cassette and that the tape passes between the guideposts. If necessary, turn the

spool clockwise to tighten the ribbon.

4Insert the cassette with the tape and ribbon positioned

between the print head and pinch roller. See Figure 10.

5Press firmly until cassette clicks into place. Make sure tape

and ribbon are positioned correctly.

6Press the button to close the tape cassette tray.

You are now ready to print your first label.

Set cassette

Remove cardboard insert

Figure 9

= 6 mm

= 9/12 mm

= 19/24 mm

switch

Push down gently

Pinch Roller

Print Head

Figure 10

5. Printing your First Label

These instructions show you how to print a die-cut label. To print a D1 tape label, refer to the DYMO

Label Software User Guide.

To print a label

1Start the DYMO Label software by doing one of the following:

•For Windows, click Start, then Programs>DYMO Label>DYMO Label.

•For Macintosh, double-click the DYMO Label icon in the folder where you installed the

software.

(Windows) The first time you open the application, you are asked to register. Follow the on-screen

instructions to register the software. You are also asked to enter your default return address and

default logo file.

2At the main window, click once on the label and type some text.

3Choose a font and a justification setting from the Formatting toolbar.

4Click to print the label.

Congratulations! You are now ready to start designing and printing labels.

For complete details on how to use the software, refer to the DYMO Label Software User Guide on the

DYMO Label CD-ROM and the online Help.

930097

DYMO bvba

Industriepark-Noord 30

9100 Sint-Niklaas

Belgium

DYMO Purchase Registration

Sanford Australia

1-11 Keysborough Ave,

Keysborough, Victoria 3173

Australia

Autres manuels pour LabelWriter DUO

Table des matières

Autres manuels Dymo Étiqueteuse

Dymo

Dymo LabelManager 450D Manuel utilisateur

Dymo

Dymo LabelWriter Twin Turbo Manuel utilisateur

Dymo

Dymo LetraTag 200B Manuel utilisateur

Dymo

Dymo LabelWriter DUO Manuel utilisateur

Dymo

Dymo LetrTAG QX50 Manuel utilisateur

Dymo

Dymo M1011 Manuel utilisateur

Dymo

Dymo Rhino 5200 Manuel utilisateur

Dymo

Dymo RhinoPRO 6000 Manuel utilisateur

Dymo

Dymo LlM 100+ Manuel utilisateur

Dymo

Dymo LetraTag Manuel utilisateur

Dymo

Dymo LabelWriter 400 Duo Guide Manuel utilisateur

Dymo

Dymo MobileLabeler Manuel utilisateur

Dymo

Dymo LabelManager 100 Manuel utilisateur

Dymo

Dymo LabelWriter SE450 Label Printer Manuel utilisateur

Dymo

Dymo Rhino 1000 Manuel utilisateur

Dymo

Dymo LabelManager 500TS Manuel utilisateur

Dymo

Dymo LabelWriter 450 Duo Label Printer Manuel utilisateur

Dymo

Dymo LabelManager 420P Manuel utilisateur

Dymo

Dymo LetraTag 100-H Manuel utilisateur

Dymo

Dymo LabelManager 500TS Guide d'installation

Dymo

Dymo LM100+ Manuel utilisateur

Dymo

Dymo LabelManager 210D+ Manuel utilisateur

Dymo

Dymo LabelWriter 400 Series Manuel du produit

Dymo

Dymo LW 450 Manuel utilisateur

Manuels Étiqueteuse populaires d'autres marques

Brother

Brother P-Touch 2420PC Manuel utilisateur

newell

newell Dymo LabelManager 210D Manuel utilisateur

Brother

Brother TD-4000 Manuel utilisateur

U-Line

U-Line BROTHER H-8754 Manuel utilisateur

Tharo Systems

Tharo Systems H-435+ Manuel utilisateur

Brother

Brother E300 Manuel utilisateur

Godex

Godex RT700 SERIES Manuel utilisateur

ID Technology

ID Technology 252 Manuel utilisateur

Labelmate

Labelmate MC-11 Manuel utilisateur

CAB

CAB XD4M/300 Manuel utilisateur

Avery Dennison

Avery Dennison Pathfinder 6057 Manuel de service

Brother

Brother P-touch PT-9700PC Manuel utilisateur

TSC

TSC PEX1000 Series Manuel utilisateur

Adkins

Adkins Label Master Manuel utilisateur

Epson

Epson LabelWorks LW-400 Manuel utilisateur

Primera

Primera 510212 Manuel utilisateur

Brady

Brady BradyPrinter S3100 Manuel utilisateur

DuraLabel

DuraLabel LabPRO Manuel utilisateur