DV8 OFFROAD RBJL-13 Manuel utilisateur

6400 SYCAMORE CANYON BLVD.

RIVERSIDE, CALIFORNIA 92507

855-680-9595

WWW.DV8OFFROAD.COM

PRODUCT

INSTALLATION MANUAL

JL FULL WIDTH REAR BUMPER

2018+ JEEP JL WRANGLER

RBJL-13

TOOLS REQUIRED SKILL LEVEL TIME REQUIRED

- Rubber mallet

- 22g wire (10-14”) and connectors

(2-6pcs)

- Zip ties

- Electrical tape/wire loom

- 8, 16, 18, 19, 21mm Sockets

- 10mm, 18mm, 21mm Wrench

- #4 Allen Bit

- Wire Cutters

- Phillips Head Screw Driver

Before you install this kit — Read and understand all

instructions, warnings, cautions, and notes contained in

this installation instruction guide. Consult your vehicle

owner’s manual for proper disconnection of electrical and

lifting of vehicle if required for installation of this product.

This install may require some technical skills and

knowledge of basic mechanical work. If you do not feel that

you are capable of performing this install please take this

product to a trained professional.

After reading this guide please contact us with any

questions or concerns before installing product.

Customer Service: 855-680-9595

DV8 Offroad is not responsible for any bodily injury or harm to you

or your vehicle as a result of an improper install.

Proper installation of this kit required knowledge of the factory

recommended procedures for removal and installation of original

equipment components. We recommend that the factory shop manual

and any special tools needed to service your vehicle be on hand during

the installation. Installation of this kit without proper knowledge of the

factory recommended procedures may affect the performance of these

components and the safety of the vehicle

• Always wear eye protection when operating power tools

Inspect all contents of this package to make sure product is not damaged

and all installation hardware has been included. If parts are missing from

kit, please be prepared to provide the following information

1. Name of purchase location

2. Bar Code on side of box

3. Date above bar code

4. Date inside box cover

- Intermediate

- 2 persons

- 3 Hours

Time to install this should only

take about three hours.

WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION

855-680-9595

NEED HELP?

Little skill level required, however,

additional assistance is required for

removal and installation of bumper.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 1 | Disconnect the wiring

harness for the license plate light.

This is located inside the bumper behind

the license plate.

STEP 2 | Disconnect the bumper

wiring harness using a panel clip tool

or at screwdriver to pry open the white

locking clip and remove.

Use a panel clip removal tool to

disconnect the two clips securing the

wiring to the vehicle.

This is located behind the bumper on the

driver-side of the vehicle.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 3 | Use a 8mm socket to

remove the bolts securing the rear inner

fender covers.

STEP 4 | Use a 16mm socket to

remove the bolts securing the bumper

brackets to the bumper. These are located

on the edges of the bumper behind the

rear tires.

STEP 5 | Use a 16mm socket to

remove the remaining four bolts securing

the bumper to the vehicle located

between the bumper and rearmost body

mount.

NOTE: Bumper may become loose while

removing these bolts. Assistance is

recommended to prevent injury and

damage to the vehicle or product.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 6 | Remove the remaining

brackets from the frame rails using either

an 18mm or 21mm socket.

Note: The tool required may vary based on

model.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 7 | If equipped with factory

backup sensors, begin by removing the

harness from factory bumper to prepare

for install. Skip to step 13 if not equipped

with factory sensors.

If equipped with factory metal bumper,

you will be able to reuse the sensor

bezels/mounts. If equipped with factory

plastic bumpers, we highly recommend

using OE sensor bezels or DV8 part

#MPRSNSR-01.

Lay out the harness ensuring the main

plug for the harness is on the driver-side

of the bumper. Push out the DV8 sensor

plugs towards the front of the bumper.

Begin by unpacking all items and

inspecting for missing pieces or damage. If

you have any concerns, please contact the

company the product was purchased from.

(4) M14x35 Hex Bolts

(2) M14 Nylon Lock Nuts

(2) M14 Spring Washers

(6) M14 Flat Washers

(2) M14 Nut Plates

(2) M12x45 Hex

(2) M12 Spring Washers

(2) M12 Flat Washers

(7) M6x20 Allen

(14) M6 Flat Washers

(7) M6 Nylon Lock Nuts

(2) M4x15 Philips Head

Bolts

(2) M4 Flat Washers

(2) M4 Spring Washers

(2) M4 Nuts

HARDWARE INCLUDED

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 8 | Push the sensor bezels

into place. The outside bezels should be

facing downwards, and the two inside

bezels should be facing down and

inwards away from the d-ring.

A rubber mallet can be used to lightly tap

them into place. The bezels should be at

against the bumper.

STEP 9 | With the bezels in place, run

the sensor wiring harness though cavity

in the bumper aligning the sensors with

the bezels. Push Sensors into bezels

ensure they have “clicked” into place.

Secure sensor harness using provided zip

tie tabs.

Note: If your jeep has factory metal bumpers,

one of the wires in the harness will need to be

lengthened. If equipped with factory plastic

bumpers, Skip to step 13.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 10 | If your bumper was

equipped with factory metal bumpers,

you will need to pull back the wire cover

on the driver-side inside sensor until all

wires are exposed.

This wire will need to be lengthened 5-10”.

STEP 11 | Using wire cutters, cut the

wire and prepare ends for wire connectors.

Using the 22g wire, crimp connectors

to your wire extension (we used non-

insulated connectors and heat shrink for

this install).

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 12 | Insert the extension

between the cut wire and secure. Re-wrap

harness and continue with the install.

If you have any questions, please reach

out to our tech team for assistance.

STEP 13 | If installing light pods,

using the hardware provided with the

lights, install them to the mounts at this

time.

For this install, we are using (2) 3” elite pod

lights.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 14 | Mount the provided

license plate mount to the bumper using

the M6 hardware include with the kit.

Secure hardware using a #4 allen and

10mm wrench .

STEP 15 | Install the provided foam

onto the license plate light.

Then, install the provided license plate

light on to the license plate mount using

the M4 hardware and a Phillips screw

driver.

STEP 16 | To connect the license

plate light, cut off the factory license plate

light plug and either cut back the factory

wire loom to expose more wire length, or

use 22g wire to extend the harness.

Using connectors, connect the factory

harness to your new license plate light.

Cover in wire loom or electrical tape. Zip

tire to backside of license plate mount.

INSTALLATION MANUAL

NEED HELP? 855-680-9595

STEP 17 | Place the provided nut

plate into the passenger side of the frame

with the nuts facing upwards.

STEP 18 | Install the mounts onto

the bumper. Using the provided M12

hardware and nut plate.

The nut plate will be used for the top bolts

on both sides.

Leave mounts somewhat loose to proper

alignments on Jeep.

Autres manuels DV8 OFFROAD Accessoires automobiles

DV8 OFFROAD

DV8 OFFROAD MTO Series Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD MPT3-01 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD TCTT2-01 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD RRUN-02 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD SRBR-03 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD SPEC Series Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD CCT2-01 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD TSJL-03 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD RBGL-05 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD RBJL-12 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD FDGL-07 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD CCBR-01 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD MPGX-02 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD FDBR-01 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD LPBM-03 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD ABJL-01 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD SRGX-02 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD FDJL-07 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD D-JP-180014-STR4 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD D-JP-181112-BK Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD CCJL-01 Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD SPEC Series Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD WINCH POCKET FAIRLEAD Manuel utilisateur

DV8 OFFROAD

DV8 OFFROAD Razor Series Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur