Duxbury Networking DUX1510P Manuel utilisateur
INSTALLATION GUIDE
8 + 2 GIGABIT LAYER 2
Managed PoE Switch
DUX1510P
DUX1510P is a Layer 2 10-port PoE+ (8 x Gigabit RJ45, 2 x Gigabit SFP) Managed
Switch. The switch is designed with new generation of high-performance hardware
and software platforms, providing flexible, cost-effective full Gigabit access and
uplink ports. As standard, it supports complete security mechanisms, improved
ACL / QoS strategy and rich VLAN capabilities. The switch is easy to manage
and maintain, meeting the user's requirements for easy to manage, high security
and low cost networks.
Web Login
Step1: In the normal operation of the device, connect the computer to the
switch's RJ45 port by network cable
Step 2: Manually changed the computer IP address to 192.168.254.X (X is 2 ~
254), subnet mask is 255.255.255.0
Step3: Open computer's browser, type 192.168.254.1 in the address box, hit
the Enter key
Step4: Enter the default username and password “admin” and then click Login
Step5: For detailed information please refer to the DUX150P User Manual
INTRODUCTION
Support 4 working modes, AI VLAN,
AI Extend AI PoE and AI QoS
Support High PoE, IEEE 802.at/af,
Max 46W output per port
150W Total PoE Power Budget
Port 1-8 support 250Meters long-dis-
tance power supply (recommended
Cat5e or 6 network cable)
Supports IEEE 802.3af/at standard,
automatically detects and identifies
devices that comply with the IEEE
802.3af/at standard and supply
power to it
Support Auto MDI/MDIX；
Adopt store-and-forward exchange
method
Intelligent power supply providing
the lowest power the PD (Power
Device) needs
With power circuit protection, pro-
tecting the safety of the PD
All ports have wire-speed forwarding
capability
Plug and play, easy to use or
Managed, supporting various Layer
2 functions (VLAN, QoS, Link
Aggregation, MSTP, Loop Protection,
IGMP-Snooping, 802.1x), Lite Layer 3
functions, PoE Management and
more Advanced settings
KEY FEATURES
1、Port funcon
1.1 Port management
Enable/disable port
Rate, duplex mode, MTU sengs
Flow control sengs
Port informaon view
1.2 Port isolaon Support single isolaon group
Support global
port isolaon
conguraon
1.3
Port mirroring
Support for exits, entrances, and full mirroring
1.4
Port speed limit
Support export, entry rate seng
1.5 Trac Stascs Support packet/byte recepon/send stascs
1.6 Port energy saving
Support 802.3az EEE port energy-saving
technology
2、
POE Management
2.1 Port PoE management
Switch POE power supply, congure port
output power
2.2
Device Informaon
View POE chip temperature and output status
2.3
Timing power supply
conguraon
Congure power supply policy, set port power
supply strategy
2.4
AI PS conguraon
Set the total power supply, zero ow duraon
3、Layer 2 funcon
3.1 Mac Address table
Support stac addion, deleon and support
aging me seng
3.2 VLAN
Support hybrid、translate port mode
Support VLAN learning mode
SupportVoice VLAN
3.3 Link aggregaon
Support stac link aggregaon
Support dynamic LACP aggregaon
INTERFACE FUNCTION LIST
3.4 Storm control
Support broadcast, mulcast, unknown
unicast control
3.5 Spanning tree
Support 802.1d (STP)
Also supports
ERPS (Private
Agreement)
Support 802.1w (RSTP)
Support 802.1s (MSTP)
3.6 DHCP-snooping
Support for stac binding
Support port Untrust/IPSGconguraon
3.7 IGMP-snooping
Support stac addion, deleon
Support v1/2/3 dynamic mulcast snooping
4、Advanced sengs
4.1 QOS
Based on 802.1p (COS) classicaon
Based on DSCP classicaon
Support SP, WRR, DRR scheduling strategies
4.2 ACL
Based on source MAC, desnaon MAC,
protocol type, source IP, desnaon IP, L4
port number
Support me-range me period management
4.3 SNMP
Support V1/V2/V3 version network
management protocol
4.4 RMON
Supports event groups, stascs groups,
history groups, and alarm groups.
4.5
LLDP
Support LLDP link discovery protocol
4.6
Loop protecon
Support ring network protecon
4.7 NTP Conguraon
Support me zone selecon, NTP server
manual addion
4.8
An-aack
Support DDOS, ICMP aack protecon
5、System sengs
5.1
User sengs
Modify user password
5.2
Network sengs
Support automac acquision of IP/stac IP
5.3
Serviceconguraon
Turn telnet port on/o
5.4
Conguraon
management
reset
5.5
Firmware upgrade
Upgrade the latest version of the soware
5.6
Log
User login, operaon, status, event log
Internet
Power
24-Port Gigabit Switch
PD
PC
Bridge IP-CameraAP
INSTALLATION DIAGRAM
Indicators
Title Color
Work
status
Descripon
POWER Power
indicator
Solid
Power is normal
O
No power, the power switch is not turned on,
power supply is abnormal
POE
POE
power
indicator
Solid
The corresponding RJ45 port is connected to the
powered device and the power supply is normal
O
The corresponding RJ45 port is not connected to
the powered device or the power supply is
abnormal
LINK/ACT
Connec
on
indicator
Blinking A valid link is established
OAn invalid link is established
SYS System
indicator
Blinking
System is funconing properly
O
System is funconing improperly Soware is
damaged
9-10 SFP
indicator
Blinking
A valid link is established on the SFP port
OAn invalid link is established on the SFP port
SHORTCUT BUTTON
QOS: Improve video data processing capabilities and improve the monitoring of
Caton and Mosaic phenomena in the network
EXTEND: 1-8 port rate down to 10Mbps, but the transmission distance up to 250 meters
VLAN: Isolating ports 1-8 from each other, suppress network storms effectively and
improve network performance
AI PS: Detect PD, power failure and restart dead equipment
RST Button
When the switch is powered on, press the button with the needle to release the
device and enter the restarting state. When the SYS lamp restarts, the device
restarts. When the switch is powered on, press and hold the button for more than 5s
to release the button and enter the reset state. When SYS is re-lit, the device is reset
successfully
Console port
Console port used to connect to computer or other terminal to manage or configure
the switch.
Installation Suggestion:
1. Connect all your networking equipment (including any PoE devices) to the switch.
2. Connect power to your switch and wait a moment for it to power on.
3. Check the status of your switch.
4. Use the switch in a clean, cool and dry environment.
5. Remove the power cable before any new devices are connected to the switch.
6. Only use CAT 5 or above to ensure maximum distance of up to 100m/250m
SUPPORT
Johannesburg
Block 2 Riviera Office Park
66 Oxford Road
Riviera
2193
Tel: +27 11 351 9800
Fax: +27 11 646 3079
Support: [email protected]o.za
Info: info@duxnet.co.za
Cape Town
1 Mews Close
Waterhouse Place
(Off Century Boulevard)
Century City
Cape Town
7441
Tel: +27 21 423 7115
Fax: +27 21 423 2463
Info: pauls@duxbury.co.za
Durban
Block 2, Suite 222
2nd Floor Island Office Park
35/37 Island Circle
Riverhorse Valley Business Estate
Durban
Tel: +27 87 943 9076 / 9088
Fax: 086 225 5125
Info: jpilla[email protected]o.za
www.duxbury.co.za
Thank you for selecting a Duxbury Networking product.
Duxbury Networking recommends that you use only the official Duxbury
Networking resources.
If you experience any technical difficulty with your product, please locate
the serial number on the label of your product and contact us on:
Table des matières
Autres manuels Duxbury Networking Changer
