Duncan Enviro DD30 Manuel utilisateur

Owners Manual

Enviro DD30

‘Smart AG Electric Drive

Operation’

Pt. No. 67453

Issue 0321

Head Office:

P.O. Box 2018

Hilton Highway, Washdyke

Timaru, New Zealand

Telephone (03) 688 2029

Facsimile (03) 688 2821

Australian Branch:

Building 2 107-117 Boundary

Road

Laverton North, Melbourne,

Victoria 3026 Australia

Telephone (03) 9369-6548

Facsimile (03) 9314-6810

Pt. No. 67453

Issue 0321

Setup, Calibration & Operating Procedure:

Read Before Operation .................. 2

Pre-calibration setup flowchart ............ 7

Calibration procedure ................... 8

DD30 Sowing Chart..................... 12

Airflow & Fan Speed .................... 14

Enviro DD30 Contents

Page

‘Enviro DD30’ Read Before Operation

Components Referred to in the Pre-Calibration Setup and Calibration Process

The following pages describe how to set the machine up for calibration, the calibration process and

subsequent adjustments to obtain the desired seed and/or fertilizer output.

Terms and words used in those instructions are shown below:-

Adjustment Handle

Toggle

‘NORMAL’ POSITION

‘FINE’ POSITION

Only switch from

normal to ne seed

if the seed hopper is

empty

Do not open the

setting above ‘25’

with the toggle set to

‘ne’ as the adjuster

will break.

Metering Setting

Scale

Pt. No. 67453

Issue 0321

‘IDLER GEAR’

HIGH = PUSHED IN

LOW= PULLED OUT

Adjustment Handle

Normal/Fine Toggle

high (idler in)

low (idler out)

Venturi Housing

with Trap Door for calibration

& gate for controlled emptying

of the bin

Components Referred to in the Pre-Calibration Setup and Calibration Process

The following pages describe how to set the machine up for calibration, the calibration process and

subsequent adjustments to obtain the desired seed and/or fertilizer output.

Terms and words used in those instructions are shown below:-

Metering motor

& Gearbox

Shaft conrmation

sensor (-not tted

to later versions) Motor mount has been cut away to

show the idler gear

‘Enviro DD30’ Read Before Operation

‘Enviro DD30’ SmartAG Overview

Front Screen

1Settings Menu

> Select the Settings tab (looks like a gearwheel) to display

the settings menu. This will mostly be used the access the

calibration screens which are described in the calibration

section of this manual.

2Display Tiles

>A display tile shows the data for the name of the tile. This

can be any input. In this case the screen is setup to display

the data relevant to the seed drill.

>Pressing on a display tile can be used to change the setting

(if available) for that tile. eg: Press and hold the Front Bin (or

Rear Bin) tile for 1 second and you will see the rate for that

bin. Use the - or + to change if needed.

>Pressing on the Applied Ha tile allows you to reset the area

to zero to record a new job.

3Front Screen Tabs

>Different tabs display different sets of display tiles. These are

preconfigured but may be customised to you liking. Please

refer to the SmartAG Operator’s Manual for details.

Note that at any time, the system may be returned to Factory

Settings using the supplied USB memory stick.

Front Screen - Overview

Pt. No. 67453

Issue 0321

‘Enviro DD30 ’ SmartAG Overview

Settings Menu - Overview

Settings Menu

1Setup Menu

> This opens the Settings and Setup menu. This enables

product calibration, machine settings and display options.

Note that all the settings for your machine are already set and

tested at the factory.

2Jobs Menu

>This opens the jobs menu.

3Alarms Menu

>This opens the alarms menu.

4Maintenance Menu

>This opens the maintenance menu.

Note that at any time, the system may be returned to Factory

Settings using the supplied USB memory stick.

Screen Tabs - Overview

Tab 2 - Bin Contents and Bin Motor ‘ON/OFF’

1Front/Rear Bin Level Estimate

> Each bin capacity is 700 litres. The value displayed is a

continuous calculation made from the density of the product

(set in the bin setup menu) and the amount (kg) of product

metered out. If setup correctly, this will show the amount (kg)

of product remaining in the bin.

2Bin Motor ON/OFF

>Quickly touch the bin you wish to toggle ON/OFF. In this

picture, the Front Bin is off and is displayed in red.

Note that at any time, the system may be returned to Factory

Settings using the supplied USB memory stick.

‘Enviro DD30’ SmartAG Overview

Note: Bin

Levels are

700 on DD30

Pt. No. 67453

Issue 0321

Start

Is seed size

between 4 and

10mm?

Locate product in 'Normal'

seed table.

Look up 'Setting Postion' for

desired output.

Yes

Is Setting Position

25mm or less?

Yes

Pull idler gear to 'out' position.

The metering shaft will rotate

at half speed for smoother

delivery at low rates. Look up

revised rates on 'Increased

Accuracy' chart for normal

sized seed.

Ensure that idler gear is

pushed in and not meshing to

the external gear. The

metering shaft will rotate at

high speed when seeding.

Turn handle on the metering

housing to the desired 'Setting

Position' for the chosen

product from the table.

Ensure that the normal/fine

toggle is not engaged with the

hex shaft and that the end is

pointing toward the metering

housing.

Locate product in 'Fine' seed

table.

Look up 'Setting Postion' and

'Rate' for desired output.

Does 'Rate' in

table specify

'low'?

Ensure that idler gear is

pushed in and not meshing to

the external gear. The

metering shaft will rotate at

high speed when seeding.

Ensure that the normal/fine

toggle is engaged with the hex

shaft. You will need to turn the

the metering handle so the

scale reads zero and engage

the toggle with the cutout in th

hex shaft.

Turn handle on the metering

housing to the desired 'Setting

Position' for the chosen

product from the table.

Perform Calibration -

refer to next page.

Perform Calibration -

refer to next page.

Pull idler gear to 'out' position.

The metering shaft will rotate

at half speed.

Empty boxes and clear old

seed and fertilizer from

metering unit. high (idler in)

low (idler out)

normal/ne toggle

‘Enviro DD30’ Pre-Calibration Setup

Only switch from

normal to ne seed

if the seed hopper is

empty

Seed Calibration

The calibration test should be done to confirm the required

seed rate to be sown and is done with the drill stationary and

level and the fan off.

Seed Calibration Procedures

1Prepare a suitable area for weighing and setup the

scales. Tare the scales with the same container that

will be used to weight the product. Scales must be

accurate to 2 grams

2 Ensure that the metering unit is free from debris. Close

the trap-door and the bin emptying gate.

3The metering unit should already be set. If not refer to

the pre-calibration flowchart on previous pages. Note

that it can be hard to adjust the settings once product is

in the bins.

4 Fill the appropriate bin. A minimum depth of 300mm is

required for calibration with normal seeds.

5Undo the elbow and place the plastic container under

the metering unit of the bin to be calibrated.

6Return to the tractor to access the SmartAG screen.

7Go to the Bin/Tank tab as shown below.

8Select the Bin that you want to calibrate.

9Select Product to change if required, touch the tick to

accept.

10 Touch tick again to accept and return to the Bin/Tank

screen.

11 Touch Rate to change the Application Rate if required.

‘Enviro DD30’ Calibration

Table des matières

Autres manuels Duncan Matériel agricole

Duncan

Duncan Fodder Chopper Manuel utilisateur

Duncan

Duncan Renovator AS6100 Manuel utilisateur

Duncan

Duncan Renovator TFD Manuel utilisateur

Duncan

Duncan Enviro DD45 Manuel utilisateur

Duncan

Duncan Electrofeed 3Pt Linkage Manuel utilisateur

Duncan

Duncan Uni-Seeder Manuel utilisateur

Duncan

Duncan Enviro 3000e Manuel utilisateur

Duncan

Duncan Renovator AS3000 Manuel utilisateur

Duncan

Duncan Renovator AS4000 Manuel utilisateur

Duncan

Duncan MK4 Renovator Manuel du propriétaire

Duncan

Duncan Enviro 740 Manuel utilisateur

Duncan

Duncan Enviro DD35 Manuel utilisateur

Duncan

Duncan Enviro DD55 Manuel utilisateur

Duncan

Duncan SLR Feeder Manuel utilisateur

Manuels Matériel agricole populaires d'autres marques

GSi

GSi PNEG-2314 Manuel utilisateur

Checchi & Magli

Checchi & Magli TEXDRIVE Manuel utilisateur

Amazone

Amazone Cenius 4003-2TX Manuel utilisateur

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manuel utilisateur

Cima

Cima BLITZ Instructions d'utilisation et d'entretien

Amazone

Amazone CombiDisc 3000 Instructions d'installation

HE-VA

HE-VA Disc-Roller XL Contour Manuel utilisateur

AGT

AGT AGT-SSFM Manuel utilisateur

Milestone

Milestone 72-84 Manuel utilisateur

KUHN

KUHN Hector 3000 Manuel utilisateur

Krone

Krone X-Disc 6200 Manuel utilisateur

Eliet

Eliet DZC450 Manuel utilisateur

Taarup

Taarup BIO+ B4000 Manuel utilisateur

Garland

Garland SHAKER 310 DPG Manuel utilisateur

stable comfort

stable comfort StableWall System Manuel utilisateur

Raven

Raven AccuBoom Manuel utilisateur

International

International 710 Manuel utilisateur

Ashland

Ashland HDW-3217-14 Manuel utilisateur