DSE RA-N1250 Manuel utilisateur
USER MANUAL
IP cameras for video surveillance
Page: 1 Page: 1 Last updated: May 2009
DSE srl - ITALY - WWW.DSE.EU
IP CAMERAS
RA-N1250 RB1
RB2-N6600-N6630-N6130
RC RD-N2260
INTRODUCTION
IP cameras are cameras that can generate a purely digital video signal that can be
transferred to a computer local area network, instead of using coaxial cables required for
analog video transport standard television.
These cameras have therefore a power outlet instead of the classic video connector BNC /
RCA and the images they generate are displayed on computers instead of TV-like monitor. E
'possible to realize an appropriate LAN network for the CCTV system or use one already
exists.
MAIN SPECIFICATIONS
Template RA-N1250 RB1-N6600 RB2-N6630 RC-N6130 RD-N2260
Sensor CMOS progressive scan CMOS progressive scan CMOS progressive scan Sony Super HAD CCD
520 TV lines
CMOS progressive scan
Max resolution. 640x480 640x480 640x480 704x576 640x480
Compression MPEG-4 / MJPEG MPEG-4 / MJPEG MPEG-4 / MJPEG MPEG-4 / MJPEG MPEG-4 / MJPEG
Dual streaming Supported - E 'can send streaming simultaneously with different compressions
Frame rate max. 30 f / sec 30 f / sec 30 f / sec 30 f / sec 30 f / sec
Objective Standard 4 mm F 2.0 4.3 mm F 2.0 6 mm F 1.6 6 mm F 1.8 4.3 mm F 2.0
lens mount S S S CS S
Illuminator 5 m. 15 m. 35 m. - 10 m.
illuminator Technology visible LEDs IR 850 nm IR 850 nm - IR 850 nm
ICR - IR removable filter - Yes Yes -Yes
Audio Bidirectional Bidirectional Bidirectional Bidirectional Bidirectional
Microphone incorporated External External External incorporated
Pan - - - - Pan 354 ° / 125 ° Tilt
Preset - - - - 32 presets - 4 tour
Motion detection Yes Yes Yes Yes Yes
PoE (power over ethernet) - Yes Yes Yes -
via RJ45 LAN cable Yes Yes Yes Yes Yes
Wireless LAN 802.11b / g - - - 802.11b / g
Alarms in / out - 1/1 1/1 1/1 1/1
Mobile access to Possible remote access from mobile phones 3GPP / ISMA / RTSP
Access Browser Internet Explorer - Mac Safari - MSN Messenger - Quicktime - Real Player - VST etc.
DHCP It - allows access to networks with automatic IP address assignment
PPPoE It - allows Log-in to the ISP in direct modem connections to the Internet
DDNS They - DDNS services allow access via the Internet without having a fixed IP
SMTP YES - it allows sending emails in case of alarm
FTP It - allows sending alerts to FTP sites
HTTP It - allows sending alerts to websites
HTTPS - to connect to secure networks
Alarms in timeslot It - enabling alarms weekly time slot
PASSWORD Protection Max 10 users - 3 levels of access
HTTPS - to connect to secure networks
overlay YES - Customizable text and date / time
Policy Area SI - To mask areas that you want to exclude from monitoring for privacy reasons
USER MANUAL
IP cameras for video surveillance
Page: 2 Page: 2 Last updated: May 2009
DSE srl - ITALY - WWW.DSE.EU
ASSEMBLY AND INSTALLATION
Package Contents
IP Camera
Power supply 220VAC / 12VDC Bracket for wall mount /
ceiling CD with software and manual.
hardware Connections
CAMERA STANDARD
In non-protected cameras connections are placed on the back of the camera.
CAMERAS DRYSUITS
In the waterproof cameras from the rear of the camera comes out of a cable with the
connections.
Connection to the LAN - The first thing to Connection to the LAN - The first thing to
to do is connect the video server to the LAN. For this purpose on the
back of all the IP cameras is a RJ45 connector. Typically you connect
to an Ethernet hub or switch network using a network cable law.
If instead of a LAN, you want to connect directly to the network
card of a single PC, you will need to use a crossover network cable
(CROSSOVER)
Wireless LAN connection - Some cameras also offer the ability to connect to the Wireless LAN connection - Some cameras also offer the ability to connect to the
wireless LAN network via Wi-Fi. These cameras are equipped with an antenna that is
screwed to the rear SMA connector. In this way, the only connection necessary for spinning
the camera will be the power supply. Obviously it is necessary to have an access point in
unable to make the wireless connection with the camera.
video output connection - In the IP cameras video output connection - In the IP cameras
there is no analog video output BNC / RCA because the video signal is not connected to a
device with standard television. Only the RC-N6130 camera that mounts an analog CCD,
internally transformed into digital, is equipped with analog video output (connector RCA internally transformed into digital, is equipped with analog video output (connector RCA
yellow). This output can be used to connect to a television apparatus, yellow). This output can be used to connect to a television apparatus,
a monitor analog or a
video recorder.
Connection AUDIO IN - All IP cameras Connection AUDIO IN - All IP cameras
They are equipped with an audio input to connect a microphone and hear the audio
environment. The microphone input is a miniplug characterized by an indication or AUDIO IN
A / IN to which one can connect an environmental microphone. AUDIO If the input is not
present, this means that the camera is equipped with a built-in microphone of place rule on
the front.
Connect AUDIO OUT - All IP cameras enable two-way audio communication so you Connect AUDIO OUT - All IP cameras enable two-way audio communication so you
can talk hands-free with people from camera. For this there is an audio output minijack so
you can connect the computer speakers. The output is distinguished by an indication AUDIO
OUT or A-OUT or SPEAKER. Audio playback is very clean and can be greatly amplified.
Supply - Supply - The cameras have
DC power supply. The power supply, provided together with the camera, it should be
connected to the power plug.
Inputs / Outputs - Some cameras feature Inputs / Outputs - Some cameras feature
a terminal block with an input and an alarm output. At the entrance it is possible to connect a
contact capable of generating the alarm actions (eg microswitch on a door). With the relay
output can be controlled electrical devices such as lighting or other. The references are as
follows:
- DI + / DI-Alarm Input
- COM / NO - Alarm output The RD-N2260, for example, the camera has the
following connections:
USER MANUAL
IP cameras for video surveillance
Page: 3 Page: 3 Last updated: May 2009
DSE srl - ITALY - WWW.DSE.EU
The alarm output is a contact Normally Open (NO) able to drive in a direct way max. 30W.
The alarm input is instead a voltage input that requires to be triggered an applied voltage 5V
or 12VDC. Programmatically it is possible to set whether the present voltage corresponds to
active or at rest alarm.
RESET button - All cameras RESET button - All cameras
They have a reset button that is typically located inside a small hole so that it can only be
operated voluntarily with a pointed tool. With the device powered by the pressure of the
button generates the device is restarted. Hold the button for 10 seconds will reset the factory
settings.
Lens Focus - Cameras Lens Focus - Cameras
They are already provided adjusted for optimum focus in the normality of most applications.
CAMERAS DRYSUITS mod. RB1 / RB2 - The development of factory fire can not be CAMERAS DRYSUITS mod. RB1 / RB2 - The development of factory fire can not be CAMERAS DRYSUITS mod. RB1 / RB2 - The development of factory fire can not be
changed CAMERAS WITH LENS ATTACHMENT C / CS mod. RCchanged CAMERAS WITH LENS ATTACHMENT C / CS mod. RC
- The focus should be adjusted depending on the lens used.
Possibly can esserenecessario
change the focal distance of the lens unlocking the attack lens threaded ring nut acting on
the small side Allen.
CAMERAS WITH ATTACK MINILENTE S mod. RA / RDCAMERAS WITH ATTACK MINILENTE S mod. RA / RD
- E 'can change the focus by rotating the silver ring that surrounds the lens.
Power Over Ethernet - The PoE function is active Power Over Ethernet - The PoE function is active
on the following models:
-RB1-N6600
-RB2-N6630
-RC-N6130
These cameras can be fed through the network cable, without using the AC adapter. And
'necessary that the SWITCH / HUB / Media Network Router PoE.
Fixing the wall / ceiling.
Bracket for wall mounting - All cameras are provided with mounting bracket that Bracket for wall mounting - All cameras are provided with mounting bracket that
allows the mounting to the wall / ceiling by means of dowels.
dome Cameras - Dome cameras as the dome Cameras - Dome cameras as the
RD-N2260 model is provided with a bracket for wall mounting which allows the mounting of
the camera a plan or upside down depending on its position with respect to the environment.
In case of mounting countdown it will be necessary to program the rotation of the shot image
in the configuration
of the camera. In
SETTINGS / BASE / CAMERA / GENERAL set MIRROR IMAGE TURNED of + REVERSE.
USER MANUAL
IP cameras for video surveillance
Page: 4 Page: 4 Last updated: May 2009
DSE srl - ITALY - WWW.DSE.EU
SET UP THE IP ADDRESS
Enable ActiveX controls
The IP cameras can be viewed and configured simply by using the browser
INTERNET
EXPLORER. To do this Explorer is created within a control environment via ActiveX
controls. First you must enable your browser Internet Explorer to download and
enforcement of such controls.
INTERNET EXPLORER / TOOLS / INTERNET OPTIONS - DATA PROTECTION -
CUSTOM LEVEL
Enable DOWNLOAD ACTIVEX CONTROLS WITHOUT ELECTRONIC
SIGNATURE - select ON or ASK FOR CONFIRMATION.
Intelligent IP Installer
On the installation CD contains a very useful program to quickly configure the IP address of
the video server. It is INTELLIGENT IP INSTALLER. Install it in the PC and run the
program.
Click on the SEARCH button. The program will scan the entire network connected to the
PC for compatible IP cameras. After a few seconds you will see the list of detected
cameras. The program is also able to detect cameras that have a class of address different
from that of the PC where you are working.
Remember, however, that to do with Internet Explorer requires that the PC and network
cameras are of the same, ie it is necessary that the first 3 IP numbers are commoncameras are of the same, ie it is necessary that the first 3 IP numbers are common
for everyone.
Select the camera and click LINK TO IE to log on opening the Internet Explorer browser.
Asked to USER NAME / PASSWORD enter the factory settings
Username: admin Password: admin
If the network you're working on managing the automatic assignment of
addresses (DHCP) the cameras
automatically acquire an address in the same class as other network equipment and you
can immediately log in using the browser. If the network requires manual changes then you
need to click Setup, and provide for the setting of network parameters adjusted to conform
to the PC on which you work.
UPnP Protocol
All cameras support the protocol Universal Plug and Play protocol (UPnP) that is enabled All cameras support the protocol Universal Plug and Play protocol (UPnP) that is enabled All cameras support the protocol Universal Plug and Play protocol (UPnP) that is enabled
in the factory. Thanks to this protocol that does not require any configuration you can also
view the IP cameras between the Explorer network resources. See the following example:
USER MANUAL
IP cameras for video surveillance
Page: 5 Page: 5 Last updated: May 2009
DSE srl - ITALY - WWW.DSE.EU
As you can see from all networked PCs also appear connected cameras and is so
immediate detect the IP address and connect to the browser by double-clicking the icon. All
without using the IP Installer software.
USER MANUAL
IP cameras for video surveillance
Page: 6 Page: 6 Last updated: May 2009
DSE srl - ITALY - WWW.DSE.EU
CONNECTION WITH BROWSER
BROWSER WINDOWS INTERNET
EXPLORER
The most immediate way to connect to the camera is to use the Windows browser. Proceed
as follows:
Type in the address space of the browser the address of the camera detected with
IP installer, as in the following example
If you want to connect, but only display the camera image without the menu buttons
you can enter the address followed by / index2.htm as in the following example. you can enter the address followed by / index2.htm as in the following example. you can enter the address followed by / index2.htm as in the following example.
If the address entered corresponds to a camera actually connected to the network
will be prompted for the password
For the first access type the default password.
Username: admin Password: admin
If it is the first time you connect to an IP camera you will be offered to install the
appropriate components ACTIVE-X. Answer yes to any request for consent. If it appears the appropriate components ACTIVE-X. Answer yes to any request for consent. If it appears the appropriate components ACTIVE-X. Answer yes to any request for consent. If it appears the
installation request ACTIVEX make sure you set your browser's security settings correctly
(see previous section)
You will see the camera control window
SAFARI BROWSER MAC
The connection procedure with MAC is identical to quiella view for IE:
Type in the browser address space SAFARI address of the camera detected by IP
installer, for example, as shown below: http / 10.0.0.26. Enter the default password required
(see above)
As with Internet Explorer, if you want to connect, but only display the camera image
without the menu buttons you can
to type the address IP followed by
/INDEX2.HTM ( es. http://192.168.0.4/index2.htm)/INDEX2.HTM ( es. http://192.168.0.4/index2.htm)
WI-FI CONNECTION
Some cameras have an antenna in order to also connect to a wireless network. To be able
to connect to a wireless access point must first make a row connection via the LAN port in
order to configure the wireless connection.
Login to spin away with the browser as seen above.
To select
USER MANUAL
IP cameras for video surveillance
Page: 7 Page: 7 Last updated: May 2009
DSE srl - ITALY - WWW.DSE.EU
SETTINGS / BASE / NETWORK / WIRELESS
Turn on your wireless service and click the Refresh button. All ACCESS POINT
reached will be shown in the window.
select the AP that you want to use and eventually modify the parameters
according to
settings used by your wireless network. By default
the camera will get a wireless IP
automatically (DHCP) and show it in the box. If you want you can select USE THE
FOLLOWING IP ADDRESS and enter the address manually.
You can then disconnect the network cable and reseat using the new wireless IP
address.
RTSP CONNECTION WITH QUICKTIME,
REAL PLAYER, VLC ETC.
It 'also possible to access the cameras with RTSP player as QUICKTIME, REAL PLAYER,
etc. VST all freely downloadable.
In the camera setup menu verify that it is enabled RTSP function that factory is active.
(SETTINGS / BASE / CAMERAS / GENERAL)
In the player enter the IP address of the camera in the following format:
rtsp: // <IP>: <PORT> /video.3gp, where IP is the public address of the camera and PORT
is the port used by the camera (default: 554)
Example: rtsp: //100.154.12.123: 554 / Video.3gp
USER MANUAL
IP cameras for video surveillance
Page: 8 Page: 8 Last updated: May 2009
DSE srl - ITALY - WWW.DSE.EU
CONNECTION WITH MOBILE PHONE
I-PHONE
E 'can connect to cameras with a phone I-Phone
Select the function SAFARI
Insert the camera's IP address
Insert the credentials of the factory access (see above) Insert the credentials of the factory access (see above)
The link page is similar to that seen on standard browsers, but pictures are
displayed one after the other and not a real video. For this reason, the recording function is
not available.
3G PHONES - STREAMING
E 'can connect the camera with a third-generation mobile phone.
In the camera setup menu to verify that it is enabled that the RTSP function of
Factory is active.
(SETTINGS / BASE / CAMERAS / GENERAL)
In STREAMING 3G connection, to insert
the IP address of the camera in the following format:
rtsp: // <IP>: <PORT> /video.3gp, where IP is the public address of the camera and PORT rtsp: // <IP>: <PORT> /video.3gp, where IP is the public address of the camera and PORT
is the port used by the camera (default: 554) Example: rtsp: //100.154.12.123: 554 /
Video.3gp
MOBILE 2.5G - WAP
E 'can connect to cameras with a 2.5G mobile phone via WAP.
In the WAP browser, type the IP address of the camera in the following format:
<IP> .mobile.wml, where IP is the public address of the camera <IP> .mobile.wml, where IP is the public address of the camera
MOBILE 2.5G - BROWSER
E 'can connect to cameras with a 2.5G mobile phone also via the phone's browser.
In the web browser, type the IP address of the camera in the following format:
<IP> .mobile.wml, where IP is the public address of the camera. <IP> .mobile.wml, where IP is the public address of the camera.
USER MANUAL
IP cameras for video surveillance
Page: 9 Page: 9 Last updated: May 2009
DSE srl - ITALY - WWW.DSE.EU
CONNECTION WITH MSN MESSENGER
This range of IP cameras is the only degree in accepting the connection via the messaging
program MSN MESSENGER freely downloadable from website www.msn.com . program MSN MESSENGER freely downloadable from website www.msn.com . program MSN MESSENGER freely downloadable from website www.msn.com .
This feature is convenient because it allows you to connect to an IP camera connected
within a network without God directing the router and without the availability of a public user
ports.
INSTALL IP INSTALLER
Before proceeding with the connection via MSN must be installed on the PC from which you
operate the IP INTELLIGENT INSTALLER program which is provided on CD and as
already mentioned in the installation section. Along with the program you will also install the
PLUG-IN MSN that allows connection.
MESSENGER INSTALL
IMPORTANT NOTE
The continuous updating of MSN software
MESSENGER makes it impossible to guarantee at all times the full functionality with the
latest version downloaded from the MSN website. Each new release of MSN may in fact
require changes in the camera's firmware.
If you notice anomalies with MSN version in your possession please contact the service to
get information about the latest compatible version that at the time of issue of this manual is
8.5, available at:
http://www.microsoft.com/downloads/details.aspx?Fa milyID =
7a1aae73-48cc-4f7a-b445-0487bd5e84ef playlang & dis = en
SET UP THE MESSENGER
After installing the program MSN MESSENGER create your personal account for accessing
the service.
First you must create a new MSN account which is a WINDOWS LIVE ID that will
be used by the IP camera. In the example that follows is supposed to
to create an MSN user the camera:
In the camera setup menu go to SETTINGS / BASE / NETWORK / MESSENGER
activate the service and enter the details created with MSN for the IP camera.
E 'can enter the MSN user name and password. NOTIFICATION IP enabled, the camera
will send its IP address to authorized users, in 'next option: PRIVACY you can add a list of
MSN users authorized to receive the information including place such as your MSN
personal user account, you access from your computer.
USER MANUAL
IP cameras for video surveillance
Page: 10 Page: 10 Last updated: May 2009
DSE srl - ITALY - WWW.DSE.EU
Now on your PC, wherever in the world there
find, reach MESSENGER
using your personal ID (which have also included in the camera PERMITS LIST). If the IP
camera is connected to the Internet, you access a window will prompt you to add the IP
camera to your contact list.
agree to add the camera to your contacts, and you can access them at will.
At this point outputs from MSN performing a DISCONNECT.
Then log back again.
You will start a call from the IP camera via MSN. The window will be displayed is the IP
address of the camera to the public Internet, both its internal IP address to the network.
E 'is the unique advantage of connecting via MSN MESSENGER, it is not necessary to
configure the router to track down the camera in the network and you can find the IP
address of internet connection without expensive fixed IP or DDNS service.
Either your new MSN access to your camera will prompt you to start the connection.
Please click on the small camera on the top left and choose VIEW WEBCAM
CONTACT. After a few
seconds It will start
camera playback
If the connection is established check that you have installed a compatible version of MSN
(see above). If playback of the video to black screen sure you have installed the Intelligent
IP INSTALLER including the XviD codec and plug-ins for MSN.
Once connected you can also click SHARE / START CONTROL PANEL. Answer
YES to the message indicating the start of an external application.
The control panel allows you to shoot movie frames and save them to your local
PC. In addition it is possible to adjust the image (brightness, contrast, etc.) and control the
movement of the camera if this is swiveled.
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels DSE Caméra IP
DSE
DSE RT Series Manuel utilisateur
DSE
DSE RK Series Manuel utilisateur
DSE
DSE RK Series Manuel utilisateur
DSE
DSE RK Series Manuel utilisateur
DSE
DSE RH Series Guide rapide
DSE
DSE RJ Series Manuel utilisateur
DSE
DSE RH Series Guide rapide
DSE
DSE RH Series Manuel utilisateur
DSE
DSE RY-BCC8 Manuel utilisateur
