DSC PC1550 Manuel utilisateur

Master Code

The 4 digit Master Code is used to arm and disarm the security system, to

program additional security codes and to change other system features.

The Master Code will be supplied to you by your installer. All keypad

entries are made by pressing one key at a time. (See Additional Codes

section)

Arming the System

Check the following items before arming the system:

Bypass Light

If the “Bypass” light is ON, insure that zones are intentionally bypassed

before arming the system (See Zone Bypassing section).

Trouble Light

If the “ Trouble” light is ON, check to see what the trouble condition is and

call for service. (See Viewing Trouble Conditions section).

Ready Light

If the “Ready” light is NOT ON, check to see that all doors and windows are

closed and that motion is stopped in areas covered by motion detectors.

The system cannot be armed unless the “Ready” light is ON indicating that

all zones are closed.

NOTE: The system may be armed with a zone bypassed or a trouble

present but your security protection will be reduced.

To Arm

Enter your 4 digit access code. As each digit is entered, the keypad

sounder will beep. If the correct access code is entered, the keypad

sounder will beep quickly and the “Armed” light will come ON.

If the access code was entered incorrectly or the “Ready” light comes ON,

the keypad buzzer will sound steadily for 2 seconds. If this occurs, press

the [#] key and re-enter your access code.

When the correct access code is entered and the “Armed” light comes ON,

exit the premises through the door indicated by your installer as the Exit-

Entry door.

At the end of the exit delay period, all lights, except the “Armed” light, will

go out and the system will be armed. The exit time delay can be changed

by your installer.

Auto-Bypass Option - Home-Away Arming

This feature, if selected by your installer, will allow you to arm your system

with any valid user code and the system will automatically bypass the

interior zones. The “Bypass” light will come on. If you exit within the allowed

exit time, the system will automatically activate the interior zones and the

“Bypass” light will go out. This feature is designed to save the customer

from having to manually bypass interior zones each time they wish to arm

the system and remain at home.

In residential applications where the system has been armed and the

interior zones are automatically bypassed, the interior zones can be

reactivated from a keypad that is outside the interior zone's protection area.

To reactivate the interior zones, press [*] then [1] and the “Bypass” light

will go out.

www.ealarm.com.my

Entry Delay Off Arming

If you wish to arm your system and eliminate the entry delay, enter [*][9]

before your access code. The “Armed” light will flash as a reminder that the

system is armed and has no entry delay. An entry through any zone

programmed as a delay zone will create an instant alarm.

e.g. To arm without entry delay, press [*][9][access code]

Disarming the System

Enter the premises only through the door(s) designated by your installer as

the entry door. Entering by any other door will sound an immediate alarm.

As soon as the entry door is opened, the keypad sounder will come on to

indicate that the system should be disarmed. Go to the keypad and enter

your four digit access code. If an error is made entering the code, press

the [#] key and enter your code again. As soon as the correct code is

entered, the “Armed” light will go out and the keypad sounder will silence.

The correct access code must be entered before the entry time expires.

The entry time delay may be changed by your installer. If an alarm

occurred during the period the system was armed, the “Memory” light and

the zone light of the zone that caused the alarm will flash for two minutes.

After the two minute period, the “Memory” light and zone light will stop

flashing and the panel will return to the ready state. Pressing the [#] key

during the two minute period will cancel the alarm memory display.

If a trouble is present when the panel is disarmed, the “Trouble” light will

come ON (See Viewing Trouble Conditions section to determine the source

of the trouble.) Note that troubles will not display while the system is in the

Alarm Memory Display Mode.

If you return home and find that an alarm has occurred while you were

away, it is possible that an intruder may still be on the premises. Go to a

neighbour's house and call the local police to investigate.

Quick Arm Feature

When the Quick-Arm feature is enabled, the system may be armed simply

by pressing [*][0] instead of the 4 digit access code. This feature allows a

person to arm but not disarm the system.

Enter [*][6][Master Code][4] to turn the Quick-Arm feature ON and OFF.

When the command is entered, the keypad buzzer will beep 3 times if

Quick-Arm is being enabled and will sound one long beep if it is being

disabled.

Press [#] to return to ready.

Door Chime Feature

The door chime feature is used, while the panel is disarmed, to provide a

tone from the keypad each time a door or window is opened or closed.

The doors and windows which will provide this indication are programmed

by your installer.

Enter [*][6][Master Code][6] to turn the door chime feature ON and OFF.

When the command is entered, the keypad buzzer will beep 3 times if the

door chime feature is being enabled, and will sound one long beep if it is

being disabled.

Press

[#]

to return to Ready.

www.ealarm.com.my

Alarm Test

Enter [*][6][Master Code][8] for a 2-second test of the keypad lights,

keypad buzzer, battery and the bell/siren.

Press

[#]

to return to Ready.

Programming Security Codes

The Master Code

Enter [*][5][current Master Code][1][new Master Code]

Press

[#]

to return to Ready.

Record your new Master Code on the System Information page in this

booklet.

Additional Codes

Up to 5 additional access codes (2 through 6) may be programmed. The

6th access code may be established by your installer as a One-Time use

code.

To pro pr

o pro pr

o program a new code:ogram a new code:

ogram a new code:ogram a new code:

ogram a new code:

Enter [*][5][Master Code][code number][new 4 digit code]

The [code number] is a single digit either 2, 3, 4, 5 or 6.

Press

[#]

to return to Ready.

If an access code already exists, it will be replaced by the new code.

Record your new code(s) on the System Information page in this book.

To ro r

o ro r

o remove a code:emove a code:

emove a code:emove a code:

emove a code:

Enter [*][5][Master Code][code number][****]

The [code number] is a single digit either 2, 3, 4, 5 or 6.

Press [#] to return to ready.

Do not erase the Master Code (code number 1).

NOTE: It is recommended that the factory default Master Code [1234] not be used.

One-Time Use Code

The One-Time Use code is designed for entry and exit of the premises for

one occasion only. The panel must be programmed by the installer for this

option to be enabled. The 6th access code is the one-time code.

To use this code, enter your one-time code as the 6th access code using

the previously described commands. When you leave the premises, arm

your system with any access code except the newly entered one-time use

code. This one-time code is given to a person (e.g. a maid) who will enter

the premises while the system is armed and you are away.

The one-time code user enters the premises and disarms the system using

the one-time access code. Upon leaving, the same code is used to arm the

system. As soon as the system is armed, the one-time code is erased and

can not be used to re-enter the premises. A different code can be provided

each time for the one-time user.

Alarm Memory Display

If the “Memory” light is ON, an alarm has occurred during the last armed

period. The alarm memory will automatically be displayed when the system

is disarmed (See Disarming the System).

Press [*] then [3] to display the zone which caused the alarm.

Press

[#]

to return to Ready.

www.ealarm.com.my

NOTE: The alarm memory is cleared each time the panel is armed so that

any alarms showing are alarms that occurred only during the last

armed period.

If An Alarm Sounds

Fire Alarm

If your system has been installed with fire detectors and the alarm sounds

in a pulsing mode, follow your Emergency Evacuation Plan immediately.

See the guide for family escape planning elsewhere in this manual.

Intrusion Alarm

If an intrusion alarm sounds (continuous Bell/Siren), the alarm may be

silenced by entering your access code. If the alarm was unintentional, call

local authorities immediately to avoid an unnecessary response.

You can determine the source of the alarm by following the instructions in

the Alarm Viewing section of this manual. Once the source of the alarm has

been corrected, the panel can be restored to its original armed state.

Zone Bypassing

Use zone bypassing when access is needed to part of the protected area

while the system is armed. Bypassed zones will not cause an alarm. Zones

that are temporarily out of service due to damaged wiring or contacts may

be bypassed to allow system arming (partial protection) until repairs can

be made. Zones cannot be bypassed after the system is armed.

To bypass zones:

Enter [*][1][Zone number(s) to be bypassed]

Enter zone number(s) as single digits (1-6).

As each zone is bypassed, the zone light will come ON. If a zone is

bypassed in error, press that zone number again and the zone light will go

OFF indicating that the zone is not bypassed.

Press

[#]

to return to Ready.

To recall last group of zones bypassed:

Enter [*][1][9]

Zone lights for the last group of zones bypassed will come ON to show

which zones are bypassed. If you wish to add or delete a zone from the

group, press [#] to exit then go to zone bypass as described above.

Press

[#]

to return to Ready.

Zone Bypassing (Continued)

For security reasons, your installer may prevent the bypass command from

working on certain zones. The “Bypass” light is ON as long as ONE or more

zones are bypassed. Do not unintentionally arm the system with zones

bypassed.

Zone bypasses are automatically cancelled each time the system is

disarmed and must be re-applied before the next arming.

Viewing Trouble Conditions

The PC1500/1550 continuously monitors a number of possible trouble

conditions. If one of these trouble conditions occur, the keypad will beep

twice every 10 seconds and the keypad “Trouble” indicator will light.

www.ealarm.com.my

Pressing any key on the keypad will silence the sounder but the “Trouble”

light will remain ON until the trouble condition is cleared. If you cannot

determine the cause of the trouble condition, contact your installer for

assistance.

Press [*][2] to display the type of trouble. A zone light will come on to

indicate which type of trouble exists.

Press

[#]

to return to Ready.

LIGHT TYPE OF TROUBLE

1 .................... Low battery.

2 .................... Loss of AC power (“Trouble” light will come ON, but

..................... keypad buzzer will not sound).

3 .................... Fuse open (BELL or AUX fuse).

4 .................... Fail to communicate with monitoring station.

5 .................... Fire loop(s) trouble.

6 .................... Loss of time on system clock.

Keypad Zones

There are three keys on the keypad labelled [F] Fire, [A] Auxiliary and [P]

Panic. These keys are only functional if they have been programmed by

your installer. The installer should indicate which of these keys are

functional by placing a coloured label next to the key symbol on the

keypad door label.

[F] Fire

Holding this key down for two seconds will sound a Fire Alarm. The alarm will

sound pulsing. The keypad will sound three beeps once the panel has

accepted the alarm. An auxiliary warning device is also activated if your

installer has connected it to your system. To silence the alarm, enter a valid

access code.

[A] Auxiliary

Holding this key down for two seconds activates this function if your installer

has programmed it. There is no audible alarm and no lights on the keypad

will come on. When the panel has accepted the alarm, the keypad will sound

a series of beeps. An auxiliary warning device is activated ONLY IF connected

to your system by your installer.

[P] Panic

Holding this key down for two seconds causes a steady tone on your siren or

bell if your installer has programmed this key for audible operation. An auxiliary

warning device is also activated if your installer has connected it to your

system. Enter a valid access code to silence the alarm.

Fire Alarm Operations

Alarm

On a fire alarm, the bell/siren will sound pulsing. The digital communicator

transmission is delayed for 30 seconds. If the alarm is not acknowledged

within the 30 second delay, the communicator will transmit to the monitoring

station.

Silence

To silence the bell/siren, press the [#] key. If the alarm is silenced and the

smoke detector is not reset, the alarm will resound after 90 seconds.

www.ealarm.com.my

Reset

To restore the smoke detector(s) to normal, press [*][7]. If the detector still

has smoke in it, the alarm will resound and the sequence described above

will repeat. If the detector is clear of smoke, the system will return to

normal.

NOTE: If you suspect that the communicator has transmitted and there is

no fire condition, call the monitoring station to avoid an

unnecessary response.

If a fire condition is apparent, follow your evacuation plan

immediately. If the alarm sounds at night, evacuate

immediately.

Testing Your System

It is recommended that you test your system weekly.

NOTE: Perform system tests in the off-peak hours, such as early morning

or late evening.

1. Inform the monitoring station that you are testing your system.

2. Disarm the system (“Ready” light ON).

3. Perform a bell/battery test by pressing [*][6][Master Code][8]. The

signal will sound for about 2 seconds. If a trouble occurs after the test,

press [*][2] to view the trouble condition.

4. Activate each sensor in turn (e.g. open a door/window or walk in motion

detector areas). Observe the zone light come ON when the zone is

activated. The zone light will go OFF when the system restores to

normal (i.e. door or window closed).

5. If they are programmed for operation, press the [F], [A], and [P] keys in

turn. The [F] key will sound the bell/siren in a pulsed mode. Enter the

access code to silence the alarm. The [A] key is silent. The [P] key may

be programmed as silent or audible. If the alarm sounds, enter the

access code to silence.

6. If the panel has a zone programmed for fire, activation will cause the

alarm signal to sound in a pulsed mode.

CAUTION: Do not use an open flame or burn materials to test a smoke

detector. Contact your alarm installer for information on safe methods to

activate a smoke detector.

7. Should the system fail to operate properly, call your alarm dealer for

service.

8. When testing is complete, call and advise the monitoring station.

Maintenance

With normal use, the system requires minimum maintenance. The following

points should be observed.

1. Do not wash the keypad with a wet cloth. Light dusting with a barely

damp cloth should remove normal accumulations of dust.

2. The battery/bell test is designed to determine battery condition, however

it is recommended that the standby battery be replaced every three

years.

3. For other system devices such as passive infrared, ultrasonic or

microwave motion detectors, glassbreak detectors or smoke detectors,

consult the respective manufacturer’s literature for testing and

maintenance.

www.ealarm.com.my

8 9

Press [F] for 2 seconds to activate

FIRE transmission.

Press [A] for 2 seconds to activate

an AUXILIARY transmission.

Press [P] for 2 seconds to activate

PANIC transmission.

THESE BUTTONS WILL NOT FUNCTION

UNLESS PROGRAMMED BYYOUR

INSTALLER.

Press

[#]..........

..........

.....

When an error is made in

entering code, then enter

code again.

To return to ready state

after using [*] commands.

TroubleTrouble

Trouble light is ON when there is a fault in

the system. Press any key to silence the

keypad beeping. Press [*] then [2] to

display the trouble type .

Zone Light Trouble Type

1 .............Low battery

2 .............AC fail (buzzer does not sound)

3 .............Fuse open (BELL or AUX fuse)

4 .............Fail to communicate

5 .............Fire loop(s) trouble

6 .............Clock needs resetting

ZoneZone

Zone light(s) when ON in the disarmed mode,

indicate an open zone. e.g. open door,

window, etc. Refer to zone chart on the

keypad door for zone information.

Bypass light comes ON when you bypass a

zone. To bypass a zone, press [*][1] and

then the zone(s) you wish to bypass. Enter 1

for zone 1....6 for zone 6. Press [#] to return to

Ready.

Memory light ON means an alarm has

occurred. Press [*] then [3]. Zone light will

come ON to indicate which zone caused

the alarm.

Ready light ON - System is ready for

arming.

Ready light OFF - System has an open

zone which must be closed or bypassed

before arming.

Armed light will come ON indicating the

system is armed. To arm, ensure “Ready”

light is ON - enter 4 digit code.

F PA

TEST SYSTEM WEEKLY

Zone 1

Zone 2

Zone 3

Zone 4

Zone 5

Zone 6

Bypass

Trouble

Arm ed

Memory

Ready

F A P

www.ealarm.com.my

Instruction

Manual

PC15OO/PC155O

1645 Flint Road, Downsview, Ontario, Canada M3J 2J6

Printed in Canada 29000203 R3

• W A R N I N G •

This manual contains information on

limitations regarding product use and

function and information on the limitations

as to liability of the manufacturer. The entire

manual should be carefully read.

www.ealarm.com.my

Autres manuels pour PC1550

Table des matières

Autres manuels DSC Système de sécurité

DSC

DSC PK5500/RFK5500 Manuel utilisateur

DSC

DSC Envoy NT9005EU Mode d'emploi

DSC

DSC PC51O Manuel utilisateur

DSC

DSC Classic PC580 Manuel utilisateur

DSC

DSC PowerSeries TR5164 Manuel utilisateur

DSC

DSC LCD5501Z Manuel utilisateur

DSC

DSC Impassa PT4 Manuel utilisateur

DSC

DSC New Classic PC585 Manuel utilisateur

DSC

DSC PC2550 Manuel utilisateur

DSC

DSC Power 832 Manuel utilisateur

DSC

DSC PowerSeries Neo Manuel utilisateur

DSC

DSC PowerSeries SCW9045-433 v1.0 Manuel utilisateur

DSC

DSC pg9901 Manuel utilisateur

DSC

DSC Envoy NT9010 Manuel utilisateur

DSC

DSC Power832 Manuel utilisateur

DSC

DSC GSM 1000 Manuel utilisateur

DSC

DSC Voice Assisted Security Control Escort 4580 Manuel utilisateur

DSC

DSC Power832 Manuel utilisateur

DSC

DSC WT5500 Manuel utilisateur

DSC

DSC 3G2055 Manuel utilisateur

DSC

DSC PC1550 Manuel utilisateur

DSC

DSC IMPASSA Manuel utilisateur

DSC

DSC PC 2500 Manuel utilisateur

DSC

DSC PowerSeries PC1832 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur