DSC ALEXOR PC9155 Mode d’emploi

PANELS, KEYPADS & MODULES

Contact your DSC distributor

www.dsc.com

1-888-888-7838

+1-905-760-3000

Quick-Start Installation Guide

1. Remove Face Plate from ALEXOR Wireless Panel

To remove the face plate, insert a small screwdriver into the 2 slots located at the

bottom.

2. Run the Power

Run AC wire and phone line through wire channel, into ALEXOR casing and wire into

terminal blocks as indicated.

3. Attach the Panel Cabinet

Mark mounting holes on wall and mount with screws provided.

4. Connect the Battery and Power It Up

Connect battery and connect face to back plate.

Provide AC to ALEXOR by plugging in the transformer

Wireless Panel & WT5500 Keypad

Just a few short steps will help you

simplify your installation process & get

you on your way to your next install

PN 29007566 R001

For product information

www.dsc.com

Product speciﬁcations and availability subject to

change without notice. Certain product names

mentioned herein may be trade names and/or

registered trademarks of other companies.

©2009 2009-03

PANELS, KEYPADS & MODULES

5. Power Up the WT5500 Keypad

Remove the mounting bracket from the keypad and insert batteries.

6. Enroll the Keypad and Wireless Devices into the Panel

Press star (*) and 1 to enroll. This must take place within the ﬁrst two minutes of

powering up ALEXOR. Keypad will display “WFKP Enrollment Successful”message.

To enroll wireless devices, use the quick enroll feature found within installers

programming section [898].

8. Program ALEXOR

Perform template programming found in section [899]. Enter the 4 digit code which

represents the functions required for basic operation through template programming.

Code prompts exist for pre-deﬁned zone deﬁnitions, reporting code formats,

communication call directions, and DLS setup. Once all codes have been programmed,

you will be prompted to enter the monitoring station phone number and account code,

DLS access code, entry and exit delays, and installer code.

Quick-Start Installation Guide

7. Mount the Keypad onto the Wall

Using the screws provided, mount the keypad bracket onto the wall.

Set keypad onto the wall bracket and snap into place.

9. Perform Placement Testing

The proposed placement of each wireless device should be tested before it is mounted

by entering section [904]-[906]. Testing the signal strength between ALEXOR and

wireless devices can be accomplished in a group (global placement test) or individually.

Installation Complete!

Wireless Panel & WT5500 Keypad

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels DSC Panneau de contrôle

DSC

DSC PowerSeries Neo Manuel utilisateur

DSC

DSC PowerSeries PC1616 Manuel utilisateur

DSC

DSC Power Series PC1616 Manuel utilisateur

DSC

DSC PowerSeries PC1555RKZ Manuel utilisateur

DSC

DSC PC2550 Manuel utilisateur

DSC

DSC LCD 5500 Manuel utilisateur

DSC

DSC PowerSeries Neo Manuel utilisateur

DSC

DSC Power632 DSCPC1555RKW Manuel utilisateur

DSC

DSC PowerSeries PC1616 Manuel utilisateur

DSC

DSC MAXSYS PC4612 Manuel de service

DSC

DSC PowerSeries PC1616 Manuel utilisateur

DSC

DSC neo HS2016 Manuel utilisateur

DSC

DSC PowerSeries Neo Manuel utilisateur

DSC

DSC Envoy NT9010DMK Manuel utilisateur

DSC

DSC Power Series Manuel utilisateur

DSC

DSC PC2585 Manuel utilisateur

DSC

DSC MAXSYS PC4020 Manuel utilisateur

DSC

DSC CLASSIC PC1555 Manuel utilisateur

DSC

DSC MAXSYS PC4020NK Guide de l'utilisateur

DSC

DSC PC5020 Manuel utilisateur

DSC

DSC PC560 Manuel utilisateur

DSC

DSC PowerSeries PC1616 Manuel utilisateur

DSC

DSC LCD5500Z Manuel utilisateur

DSC

DSC CP-5M Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques