Dr Robot X80SV Manuel utilisateur
Copyright © 2001 - 2013, Dr Robot Inc. All Rights Reserved.
www.DrRobot.com
WiFi Mobile Robot Development Platform
with High Resolution Pan-Tilt-Zoom Camera
X80SV
Quick Start Guide
Copyright © 2001 - 2013, Dr Robot Inc. All Rights Reserved.
www.DrRobot.com
WARNINGS
Do NOT power on the robot before reading and fully understanding the
operation procedures explained in this manual.
Neither the robot, nor the program is bug free, accidence could happen; you
have to make sure that the robot always maintains a safe distance from
people during operation.
The robot should be turn off (i.e. the power switch should be on OFF
position) when not in used. Battery should be fully charged before
storage. Battery pack should be recharged every two weeks while in
storage.
Failure to follow these warnings could cause serious injury or death and/or
damage to the robot.
Copyright © 2001 - 2013, Dr Robot Inc. All Rights Reserved.
www.DrRobot.com
Copyright Statement
This manual or any portion of it may not be copied or duplicated without the expressed written consent of Dr
Robot.
All the software, firmware, hardware and product design accompanying with Dr Robot’s product are solely owned
and copyrighted by Dr Robot. End users are authorized to use for personal research and educational use only.
Duplication, distribution, reverse-engineering, or commercial application of the Dr Robot or licensed software and
hardware without the expressed written consent of Dr Robot is explicitly forbidden.
www.DrRobot.com
Contact
General: [email protected]
25 Valleywood Drive, Unit 20
Markham, Ontario, L3R 5L9, Canada
Tel: (905) 943-9572 Fax: (905) 943-9197
Copyright © 2001-2013, Dr Robot Inc. All Rights Reserved.
www.DrRobot.com
- 4 -
Table of Contents
Introduction 5
Key Features 5
Sensors and External Components 6
Operation Scenario 8
Software Installation 9
Robot Operations 10
Recharging 13
Open the Sample Source Code 13
Further Development & Programming 13
Network Connection and Login Information 14
Network Settings 14
Advanced Network Settings 14
Copyright © 2001-2013, Dr Robot Inc. All Rights Reserved.
www.DrRobot.com
- 5 -
Introduction
X80SV is designed and built on X80 robot base, featuring high resolution Pan-Tilt-Zoom camera.
Key Features
High resolution Pan-Tilt-Zoom Camera with two-way audio capability
Two 12V motors with over 300oz.-inch (22kg.cm) torque each
Fully wireless networked 802.11g
OS independent application development tools
Max speed of 1 m/sec
128x64 graphic LCD, Display image, message or sensor data
Collision detection sensors include 3 Ultrasonic range sensors and 7 IR range sensors
2 Pyroelectric Human Motion Sensors
Comprehensive circuit protection
Max payload 10 kg (optional 40 kg) with robot weight of 3 kg
Dimension 38cm (L) x 35cm (W) x 28cm (H)
Extended operating time. 3 hours nominal operation time for each recharging
Upgrade options:
o
Supplementary sonar sensors, temperature sensors, acceleration/tilting sensor, or customized
sensors can be added.
o
Vision-landmark base indoor localization (indoor GPS, position/orientation) sensor and the
landmarks together provide precise position and direction information covering every inch of the
floor.
o
Laser scanner.
o
Power and battery systems for 6-hour operation time are available.
Copyright © 2001-2013, Dr Robot Inc. All Rights Reserved.
www.DrRobot.com
- 6 -
Sensors and External Components
The figure below illustrates the key functional components you will identify on the outside of X80SV robot.
X80SV Overview
The robot comes with 3 ultrasonic range sensors and 7 IR range sensors. These range sensors are for
environment detection and collision avoidance.
X80SV Sensor Module Location (Top View)
IR Range
Pan-Tilt-Zoom
Camera
Ultrasonic Sensor
Human Sensor
Main Power Switch
12V Battery Pack
Camera Antenna
Robot WiFi
Module Antenna
Quadrature
Encoder
IR Range
Copyright © 2001-2013, Dr Robot Inc. All Rights Reserved.
www.DrRobot.com
- 7 -
Sensor Module Location
Ultrasonic #1 H – Left front
Ultrasonic #2 I – Middle front
Ultrasonic #3 J – Right front
Human Sensor #1 M – Left front
Human Sensor #2 N – Right front
Infrared Range Sensor #1 A – Front left
Infrared Range Sensor #2 B – Front middle
Infrared Range Sensor #3 C – Front middle
Infrared Range Sensor #4 D – Front right
Infrared Range Sensor #5 E – Right
Infrared Range Sensor #6 F – Rear
Infrared Range Sensor #7 G – Left
Quadrature Encoder #1 K - Left , use channel 1
Quadrature Encoder #2 L - Right, use channel 2
Copyright © 2001-2013, Dr Robot Inc. All Rights Reserved.
www.DrRobot.com
- 8 -
Operation Scenario
Diagram below shows the typical operation scenario. The X80SV is a wireless networked robot. It connects to
the wireless AP or router via IEEE 802.11b/g network. The Local PC running the X80SV Control program could
connect to this network via either:
Network cable – Connect the host PC to one of the LAN ports on the back of the router (DO NOT
connect to the WAN port), or
Wireless – To connect the Local PC to the wireless router, configure the Local PC’s wireless settings
using the default wireless configuration settings found in the Network Connection session of this manual.
Typical Operation Scenario
Note: The Local PC could also be mounted on the robot instead off the robot if your application requires so.
User could be able to control the robot, see, talk and listen through the robot via the Dr Robot®Control program.
User could write his own remote
control program or contact
support.
Copyright © 2001-2013, Dr Robot Inc. All Rights Reserved.
www.DrRobot.com
- 9 -
Software Installation
You should install the “X80SVControl” program from the installation CD.
After program installation, you will find the following programs under the “Start-All Programs” list, and they are
installed under the “Program Files” folder.
Dr Robot Inc – X80SV Control
Dr Robot Inc – WiRobotGateway.exe
“SourceCode” folder contains a copy of X80SV sample code for Visual Studio 2008. It is locate under default
installation folder (such as “C:\Program Files\Dr Robot Inc\Dr Robot X80SV Control Program\”)
* DirectX ®SDK is required. You could download it from Internet
* Microsoft®.Net 3.5 Framework is required. You could download it from
Motion/Sensor
System
Motion Control
Gateway
(Port 10001*)
Robot WiFi Local PC
X80SV
Control Program
Pan-Tilt-Zoom
Camera
(192.168.0.199:
8081 *)
* Default Settin
g
Copyright © 2001-2013, Dr Robot Inc. All Rights Reserved.
www.DrRobot.com
- 10 -
Robot Operations
Step 1: If you have not installed the demo and support programs, insert the
installation CD to CDROM and run the “Setup.exe” program that is under “X80SV
Control Installation” folder.
Step 2: Connect the PC to the wireless router (one of the LAN ports) (the router
has IP 192.168.0.200) included in the package.
Step 3: Push red power switch on the front to turn on the robot.
Step 4: Run the “WiRobotGatewayforWiFi.exe” from Start -> All Programs -> Dr
Robot Inc -> WiRobotGateway.exe, Use “drrobot1” as robot ID, enter your robot IP address to “IP” textbox,
“10001”as “Port”, and then click “Connect”.
Step 5: Run the “X80SV.exe” from Start -> All Programs -> Dr Robot Inc -> X80SV Control. Once the GUI popup,
enter the camera login information, and then click “Connect”.
Table des matières
