DPS Telecom Remote Status Panel Manuel utilisateur

USER MANUAL

Remote Status Panel for NetGuardian

August 17, 2010

Visit our website at www.dpstelecom.com for the latest PDF manual and FAQs.

D-OC-UM108.17100 Firmware Version 1.0A

This document contains proprietary information which is protected by copyright. All rights are reserved. No part of this

document may be photocopied without prior written consent of DPS Telecom.

All software and manuals are copyrighted by DPS Telecom. Said software and manuals may not be reproduced, copied,

transmitted or used to make a derivative work, by either mechanical, electronic or any other means in whole or in part,

without prior written consent from DPS Telecom, except as required by United States copyright laws.

The material in this manual is for information purposes and is subject to change without notice. DPS Telecom shall not be

liable for errors contained herein or consequential damages in connection with the furnishing, performance, or use of this

manual.

Notice

August 17, 2010

Revision History

Initial release

ContentsVisit our website at www.dpstelecom.com for the latest PDF manual and FAQs

Overview: Remote Status Panel for NetGuardian1 1

Shipping List2 2

Specifications3 3

Installation4 4

Tools Needed4.1 4

Wall Mounting4.2 4

Power Connection4.3 5

NetGuardian Port4.4 6

Craft Port4.5 6

Visual Display5 6

Remote Status Panel Status LEDs5.1 7

Audible Alarm and ACK Button6 8

Craft Port and Firmware Upgrades7 8

Technical Support8 9

Overview: Remote Status Panel for NetGuardian1

Remote Status Panel

The Remote Status Panel for NetGuardian is an annunciation device that displays operational status of the

NetGuardian and Expansion Unit The connected NetGuardian completely controls the audiovisual display of the

Remote Status Panel, which only responds to the servers' commands.

The front panel features six large bi-color (red and green) LEDs. Once provisioned, the LEDs will display red

when alarms occur and the speaker will sound.

The speaker can be silenced by OFF command from the NetGuardian or the ACK (Acknowledge/momentarily

silence) button on the front of the unit.

Shipping List2

Please make sure all of the following items are included with your Remote Status Panel. If parts are missing, or if

you ever need to order new parts, please refer to the part numbers listed and call DPS Telecom at

1-800-622-3314.

Remote Status Panel for NetGuardian

D-PK-RSPNG

Remote Status Panel User Manual DB9M-DB9F Download Cable 6 ft.

D-OC-UM108.17100 D-PR-045-10-A-04

x2 x4

2 Wall Mount Brackets 4 Wall Mount Bracket Screws

x4 x4

Four Rack Screws Four Metric Rack Screws

x2 x2

Two Power Connector Plugs Two 1/2-Amp GMT Fuses

RJ12 to RJ45 Connection Cable RJ45 to RJ45 Connection Cable

D-PR-1033-10A-01 D-PR-1028-10C-01

(for connection to NetGuardian DX) (for connection to NetGuardian)

Specifications3

Dimensions: 6.136" H x 17" W x 1.2" D (15.5 cm x 43.2 cm x 3.05 cm)

Mounting: Wall mount

Power Input: –48 VDC dual power inputs (–40 VDC to –70 VDC)

Fuse: 1/2 Amp GMT

Current Draw: 250mA

Protocols: DCPx

Interfaces: 1RJ45 RS232 port

1 DB9 Craft port

Visual Interface: 5bicolor (red and green) NetGuardian status LEDs

2 Remote Status Panel NetGuardian status LEDs

Audible Notification: Alarm speaker with ACK (momentarily silence) button

Operating Temperature: 35°–140° F (1.67°–60° C)

Operating Humidity: 0%–95% noncondensing

Installation4

Tools Needed4.1

To install the Remote Status Panel, you'll need the following tools:

Phillips No. 2 Screwdriver Small Standard No. 2 Screwdriver

Wall Mounting4.2

The Remote Status Panel can be flush or rear-mounted

The Remote Status Panel is wall mounted using the 2 wall mount brackets supplied with the unit. Attach the

brackets in the wall mount locations shown here.

Power Connection4.3

Power connectors and fuses

The Remote Status Panel has two screw terminal barrier plug power connectors, located on the left side of the

back panel.

Before you connect a power supply to the Remote Status Panel, test the voltage of your power supply:

·Connect the black common lead of a voltmeter to the ground terminal of the battery, and connect the red

lead of the voltmeter to the battery's –48 VDC terminal. The voltmeter should read between –43 and –53

VDC. If the reading is outside this range, test the power supply.

To connect the Remote Status Panel to a power supply, follow these steps:

1. Remove the fuses from the back panel. Do not reinsert the fuse until all power connections have

been made.

2. To ground the Remote Status Panel, connect a grounding wire to the grounding lug.

3. Remove the power connector plug from Power Connector A. Note that the plug can be inserted into the

power connector only one way — this ensures that the barrier plug can only be reinserted with the

correct polarity. Note that the –48V terminal is on the left and the GND terminal is on the right.

4. Insert a battery ground into the power connector plug's right terminal and tighten the screw; then

insert a –48 VDC line to the plug's left terminal and tighten its screw.

5. Push the power connector plug firmly back into the power connector. If the power feed is connected

correctly, the LED by the connector will light GREEN and the Remote Status Panel will power up. If

the polarity of the power feed is reversed, the LED by the power connector will light RED and the

Remote Status Panel will NOT power up — you won't see any other LEDs light or hear any sounds

from the unit. Reversing the polarity does not harm the unit, but you should immediately remove the

fuse and reconnect the power leads correctly.

6. Repeat Steps 3–5 for Power Connector B.

7. Reinsert the fuse to power the Remote Status Panel.

When power up is complete, the front panel Power LED will light GREEN.

NetGuardian Port4.4

Connect the NetGuardian that will control the Remote Status Panel to the RJ45 NetGuardian port on the right

side of the back panel. The pinout for this port is shown below.

NetGuardian port pinout

Craft Port4.5

Use the front panel craft port only when a firmware upgrade is required. No provisioning of the unit

should be required. To upgrade firmware, connect the included DB9 download cable from your PC's

COM port to the craft port. Pinout is shown here.

12345

GND

6789

CTS

Pin # Signal Description

1Not connected

2TX Transmit data

5GND Ground

6Not connected

7CTS Clear to send

9Not connected

Recieve Data

Not connected

Request to send

DB9 RS-232

RTS

Visual Display5

The Remote Status Panel's visual displays are completely controlled by commands from the connected

NetGuardian.

Each one of the LEDs can be associated to alarm points. If there is an active alarm, the LED will be red. If there

are no alarms, the LED will be off. A blinking LED means there was a change of state for the alarm point the

LED was associated with.

Table des matières

Autres manuels DPS Telecom Matériel réseau

DPS Telecom

DPS Telecom ECU LAN Manuel utilisateur

DPS Telecom

DPS Telecom HVAC Controller G3 Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian 16 G2 Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian 16A Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian 832A Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian 240T Instructions d'utilisation

DPS Telecom

DPS Telecom NetGuardian 216 G4 Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian 832A Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian ENV Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian 420 Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian 216F Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian 832A Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian 216 G3 Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian 832/864A Manuel utilisateur

DPS Telecom

DPS Telecom T/Mon NOC Manuel utilisateur

DPS Telecom

DPS Telecom Net Dog 82 IP Manuel utilisateur

DPS Telecom

DPS Telecom DAC-P Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian 832A G5 Manuel utilisateur

DPS Telecom

DPS Telecom T/Mon/IAM Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian AAR HC Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian BSM Manuel utilisateur

DPS Telecom

DPS Telecom NetGuardian 480 G3 Manuel utilisateur

DPS Telecom

DPS Telecom CellVoice 16 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur