Dormakaba RCI 0162 Manuel utilisateur
Instructions
1. Mark horizontal center line (CL) of existing device latch from active door to inactive door. Align center of Double Door Housing
(DDH) with horizontal centerline marked on inactive door and square it with edge of the inactive door. Maintain 3/16” minimum
gap between the exit device & strike face for proper functioning of exit device. See IS0162 for details.
2. Mark the mounting holes for the DDH on the inactive door using DDH as template.
3. Drill two 13/32” (10.5mm) holes through inactive door).
4. Mount DDH to inactive door using hardware as shown.
Note: Wire access hole is not provided, drill DDH as required.
5. Make wire connections from the power source to the appropriate wire harness supplied. Use the 12V harness for 12VDC,
12-24VAC or 11-16VAC. Use the 24V harness only for 24VDC.
6. Mount the electric strike with 1/4-20 UNC (Hole C) screws provided in the outer oval mounting holes (the
outer slots). Adjust electric strike horizontally until exit device latch fully engages with the door closed.
Note: Ensure a 1/16” [1.5mm] clearance between exit device latch and the electric strike keeper is maintained.
7. Tighten the two mounting screws and check operation. Adjust the horizontal position of electric strike as required.
8. Using the electric strike as a marking template, drill & tap for 1/4-20 UNC (Hole D). Using the 1/4-20 UNC screws provided
secure the electric strike through the locking holes.
Note: 0162 strike is not adjustable after installing these screws.
IMPORTANT: The fire and/or security ratings shown on the (F)0162 strike labels no longer apply with the use of the double door
housing.
INSTALLATION 0162
Double Door Housing for
Surface Mounted Rim Strike
IS0DDH PCN18003
R01-18TG
0162 Typical Double Door
Housing Assembly
C
L
INACTIVE
DOOR
SEX NUT 1/4-20
WITH 13/32" HOLE
THROUGH (DOOR)
(2 PLACES)
HOLE C
1/4-20 X 1"
ADJUSTMENT
SCREW
HOLE C
1/4-20 X 1"
SCREW
HOLE D
1/4-20 X 1"
LOCKDOWN
SCREW
(2 PLACES)
3-3/4” (95mm)
7/8” (22.2mm)
1/4-20 X 2.5"
(2 PLACES)
0162 DOUBLE
DOOR HOUSING
© 2018 dormakaba Canada Inc. | dormakaba Group
www.rutherfordcontrols.com • PHONE: 1.800.265.6630 • FAX: 1.800.482.9795 • E-MAIL: [email protected]
Instructions
1. Mark center line (CL) of existing device latch from active door to inactive door. Align center of Double Door Housing (DDH) with
horizontal centerline marked on inactive door and square it with edge of the inactive door. Maintain 3/16" minimum gap between
the exit device & strike face for proper functioning of exit device. See IS0161 for details.
2. Mark the mounting holes for the Double Door Housing (DDH) on the inactive door using DDH as template.
3. Drill two 13/32" (10.5mm) holes through inactive door.
4. Drill wire access hole into desired area of DDH. Pull two (2) wires through the access hole and connect to strike
(polarity is not critical).
5. Temporarily mount 0161 strike to DDH through the slotted holes (Hole C) using 1/4-20 UNC x 1" screws provided.
6. Mount DDH to inactive door using the two (2) 1/4-20 x 3” screws and 1/4-20 Sex Nuts supplied.
7. Adjust electric strike insert horizontally, if necessary, until Pullman Latch engages when door is closed. (See Fig. 3 on 0161
installation instructions if further horizontal insert adjustment is necessary).
8. Mark, drill and tap Hole D for 1/4-20 x 1” provided to secure the final location.
IMPORTANT: The security ratings shown on the 0161 strike labels no longer apply with the use of the double door housing.
INSTALLATION 0161
Double Door Housing
DETAIL F
SCALE 0.2 : 1
1
1
2
2
3
3
4
4
A A
B B
DRAWING NO
SIZE
REV
REV ECN BY DATE
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
RCI. ANY REPRODUCTION IN PART OR
AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF RCI IS PROHIBITED.
DRAWING UNITS: METRIC
ANGLE VIEW:
DO NOT SCALE DRAWING
1 PLACE DECIMAL 0.5
2 PLACE DECIMAL 0.25
ANGLES 0.5
METRIC GENERAL TOLERANCES
UNLESS OTHERWISE SPECIFIED
3RD ANGLE PROJECTION
TITLE
DRAWN BY
CHECKED BY
DATE
DATE
SCALE
0161 INSTALLATION
01A01-I02 0
ntalebi 7/17/2008
B1 : 1
INACTIVE
DOOR
0161 DOUBLE
DOOR HOUSING
C
L
SCREW
1/4-20 x 3”
DRILL
13/32” HOLE
(2 PLACES)
ACTIVE
DOOR
EDGE
TYPICAL SURFACE
EXIT DEVICE
SEX NUT
1/4-20
HOLE C
ADJUSTMENT
SCREW
1/4-20 x 1”
HOLE D
LOCKDOWN
SCREW
1/4-20x1”
HOLE D
LOCKDOWN
SCREW
1/4-20 x 1”
HOLE C
ADJUSTMENT
SCREW
1/4-20 x 1”
0161 Typical Double
Door Housing Assembly
© 2018 dormakaba Canada Inc. | dormakaba Group
www.rutherfordcontrols.com • PHONE: 1.800.265.6630 • FAX: 1.800.482.9795 • E-MAIL: [email protected]
Autres manuels Dormakaba Serrure de porte
Dormakaba
Dormakaba ML530 Manuel utilisateur
Dormakaba
Dormakaba Saflok RT Manuel utilisateur
Dormakaba
Dormakaba 143 Series Manuel utilisateur
Dormakaba
Dormakaba 100 Manuel utilisateur
Dormakaba
Dormakaba AUDITCON 2 Series Manuel utilisateur
Dormakaba
Dormakaba 79 Series Manuel utilisateur
Dormakaba
Dormakaba 9000DE Series Manuel utilisateur
Dormakaba
Dormakaba ED50LE Manuel utilisateur
Dormakaba
Dormakaba 8300 Series Manuel utilisateur
Dormakaba
Dormakaba Saffire LX Manuel utilisateur
Dormakaba
Dormakaba PowerPlex 2000 Series Manuel utilisateur
Dormakaba
Dormakaba RCI 4 Series Manuel utilisateur
Dormakaba
Dormakaba RCI 6 Series Manuel utilisateur
Dormakaba
Dormakaba BEST Switch Core Manuel utilisateur
Dormakaba
Dormakaba SVA 2000 Manuel utilisateur
Dormakaba
Dormakaba Confidant RFID Manuel utilisateur
Dormakaba
Dormakaba Saflok SR Series Manuel utilisateur
Dormakaba
Dormakaba US 10 Manuel utilisateur
Dormakaba
Dormakaba Best SSRLS-3 Manuel utilisateur
Dormakaba
Dormakaba SVP Manuel utilisateur
