DMP Electronics LT-1461 Manuel utilisateur
© 2016 Digital Monitoring Products, Inc.
Information furnished by DMP Video is believed to be accurate and reliable.
This information is subject to change without notice.
FCC Information
FCC compliance: Please take attention that changes or modication not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio communications. If this product does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different than that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the radiator
and your body.
SecureCom Video 8-Channel NVR User Guide i
V-4408D SecureCom Video 8-Channel NVR User Guide
Table of Contents
Section Page
Introduction ..............................................................1
What is an SecureCom Video 8-Channel NVR .........................1
Live View ...................................................................2
Quick Setting Toolbar................................................3
Right-click Menu Options ..........................................4
Menu ..................................................................................6
Playback..............................................................................6
Export .................................................................................8
Manual ..............................................................................10
Conguration .....................................................................10
Maintenance ......................................................................10
ii SecureCom Video 8-Channel NVR User Guide
SecureCom Video 8-Channel NVR User Guide 1
Introduction
What is an SecureCom Video 8-Channel NVR
The SecureCom Video 8-Channel NVR is a Network Video Recording device with 1 TB of video storage. The eight channels
represent eight network/IP SecureCom Video or ONVIF compatible cameras.
Power up the SecureCom Video 8-Channel NVR. Live View displays what each camera is viewing, providing you with the
latest in computer technology to create the most advanced, user friendly, wireless/wired security camera system available.
With a monitor and mouse plugged into your NVR, you can view exactly what your cameras are recording in real time. You
can zoom in using the Digital Image tool to get a closer look at what might seem suspicious.
Live View can be set to auto-switch so the Live View viewing monitor can cycle through all the cameras and display each
camera view on a monitor. Clips can be created and exported and sent to interested persons.
As part of our commitment to reducing false alarms, we would like to encourage you to read this guide thoroughly. All the
information contained here can help you quickly, and comfortably, learn the SecureCom Video 8-Channel NVR operation.
2 SecureCom Video 8-Channel NVR User Guide
Live View
• Live View is the rst display you see when the NVR powers
up.
• All cameras connected to the NVR whether wireless or wired,
will display immediately.
• The default live view screen is 1+7 multi screen view (see
below).
• Live View displays each camera in real time. One or more
camera screens may be displayed at one time.
• Right click using your mouse to view the Right-click Menu
options. Right Click Menu options provide a way for you to
change the layout of your Live View screen. See the Right
Click Menu options sections for a ful list of options.
• In Live View, when you click on a camera window a Quick
Setting toolbar displays at the bottom or top of the window.
Figure 1: Live View
SecureCom Video 8-Channel NVR User Guide 3
Quick Setting Toolbar
The Quick Setting toolbar displays when a left-click on mouse is made on the Live View camera viewing window. The toolbar
displays at the top or bottom of the selected camera screen. The tools when clicked controls the current active window.
Tools that are unavailable will be grayed out.
Start and Stop Recording
Starts and stops continuous recording manually on the active camera. While watching a live camera view, you can start or
stop recording on individual cameras. All recordings are available to view in Playback from the Right-Click Menu. When the
camera is recording, the Recording icon will turn red. Click the icon again to stop recording and the icon turns gray.
Instant Playback
Click on the Instant Playback button to view up to ve minutes of instant playback of the camera recording. Only recording
les recorded during the last ve minutes on the camera will be played back. If no recording is found, it means the camera
was not recording during the last ve minutes. The Instant Playback Slider toolbar (See Figure 3 above) takes the place of
the Quick Setting Toolbar. The slider can be moved forward or backward to move the recording forward and backward for
the last ve minutes of recorded video. Place the mouse over the slider and hold down the left mouse button to move the
slider on the Instant Playback Slider bar.
Digital Zoom
Digital Zoom expands the camera to a full window with a picture in picture window in the bottom right-hand corner of the
screen. In the picture in picture window is a zoom box, that can be moved by holding down the left mouse button and
dragging the box to a specic area. Right-click to return back to Live View.
Close
Closes the Live View toolbar.
Figure 2: Quick Setting Toolbar Figure 3: Instant Playback Slider
4 SecureCom Video 8-Channel NVR User Guide
Right-click Menu Options
Right-click on the mouse anywhere on the Live View screen and the Right-click Menu displays as shown in Figure 4.
Menu Option Description
Menu Displays a menu window with the following available options:
Playback, Export, Manual, Maintenance and Shutdown. These options
can control one or more cameras at the same time.
The following Right-click Menu items changes the Live View viewing window. All
camera displays are in real time live view.
Single Screen Single full screen window of the selected camera from the drop-
down list.
Multi-screen Displays multiple camera views for live-viewing.
2 * 2 = First four cameras are displayed in the four corners of the
screen. Two along the top half of the monitor screen and two along
the bottom half.
1 + 5 = One camera display is larger than the other ve camera
displays on the same screen of the monitor.
1 + 7 = One camera display is larger than the other 7 camera
displays on the same screen of the monitor.
3 * 3 = First six cameras are displayed. Three along the top half
of the monitor screen and three along the bottom half.
Previous Screen Changes from the current Live View camera to the previous camera in the list. If you have 8 cameras and
you are watching 4 (2*2 multi-screen view) the previous 4 cameras will display.
Next Screen Changes from the current active camera to the next camera in the list.
Start Auto-Switch Enables or disables the auto-switch cycles of viewing of the active cameras.
Figure 4: Right-Click Menu Options
SecureCom Video 8-Channel NVR User Guide 5
Playback Short cut to the Menu>Playback option. Allows playback of previous recordings of one or more cameras
set for a specied date and time. See Playback in the Menu Section.
PTZ Control Only available on Pan and Tilt cameras. A set of controls will display providing the ability to move the
camera view up, down, right and left. Clicking on the light bulb icon will toggle turning on or off the
camera LED light if the camera supports a light.
Output Mode Four options in viewing Live View cameras on your monitor is supported:
• Standard
• Bright
• Gentle
• Vivid
Figure 5: PTZ Controls for Pan and Tilt Cameras
6 SecureCom Video 8-Channel NVR User Guide
Menu
The Menu displays with the following available options: Playback, Export, Manual, Conguration, Maintenance, and Shutdown.
Playback
Playback menu option plays back video recorded on the NVR by each camera. You can view one or all
cameras simultaneously by marking the check boxes of the cameras from the list on the right hand side
of the screen. The timeline bar along the bottom displays a blue indicator of when the camera(s) were
recording on that specic day.
The bottom right hand side of the playback screen is a calendar. Each highlighted date on the
calendar, a recording is available of the selected cameras for playback. Use the mouse to click any
point of the timeline bar or drag the timeline bar to locate a specic time.
Two tool bars are located along the bottom of the playback screen just below the timeline.
Figure 6: Menu Figure 7: Playback Menu
Figure 8: Camera list and
calendar of recordings
Figure 9: Playback video toolbar and controls
Table des matières
Autres manuels DMP Electronics Matériel réseau
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
