DMP Electronics XR150FC Series Manuel utilisateur
SYSTEM USER GUIDE
XR FIRE CONTROL PANEL
While the fire alarm horns, strobes, or sirens are going o, use one of the following
methods to silence the alarm:
1. Turn the keyswitch to enable the four function keys, then press the
SILENCE key.
2. Enter your User Code, then press COMMAND.
Note: You may silence an alarm using both of the above methods on the
Remote Fire Command Center too.
HOW TO HANDLE AN ALARM
Get to Know the Fire Command Center...... 1
The Select Keys ......................................................... 2
Data Entry Keys......................................................... 2
The Back Arrow Key................................................ 2
The Command Key................................................... 2
Status LEDs................................................................. 3
Entering Alpha Characters.................................... 3
Entering Non-Alpha Characters.......................... 4
Using the Keypad ..................................................... 5
User Options............................................................... 8
Four Function Keys.................................................. 9
Special Fire Command Center Displays ........ 10
Special Fire Command Center Tones...............13
User Menu......................................................14
User Menu Options .................................................14
Accessing the User Menu .....................................16
Alarm Silence ............................................................17
Sensor Reset..............................................................18
Lockdown ...................................................................19
TABLE OF CONTENTS
Door Lock/Unlock................................................. 20
Door Access...............................................................21
Outputs On/O.......................................................22
Favorite.......................................................................23
Zone Status...............................................................24
System Status ..........................................................26
System Test...............................................................27
User Profiles............................................................. 30
User Codes................................................................36
Extend Closing........................................................ 40
Setting Schedules....................................................41
Setting Holiday Dates.......................................... 48
Setting the Date and Time................................. 49
Ambush Codes .........................................................51
Display Events..........................................................52
Service Request ......................................................55
Fire Drill ......................................................................56
Common Keypad Displays ......................... 57
FIRE CONTROL PANEL FEATURES
Figure 1: Fire Control Panel Features
Keyswitch
POWER
TROUBLE
ALARM
COMMAND
1 2 3 4
5 6 7 8
9 0
ABC DEF GHI JKL
MNO PQR STU VWX
YZ
ENABLE
SILENCE
RESET
TEST
DRILL
Fire Command Center
Select KeysLCD DisplayStatus LEDs
Function Keys
Data Entry Keys
Back Arrow Key
COMMAND Key
Digital Monitoring Products, Inc. | XR Fire Control Panel User Guide 1
GET TO KNOW THE FIRE COMMAND CENTER
Your system comes equipped with a built-in, easy-to-use Fire Command Center
that allows you to properly operate the system. The Command Center is also
available in a remote version. The keyswitch to the left of the keyboard must be
turned to the “enable” position before you can use the four functions keys. It is
not necessary to use the keyswitch when using a user code to perform operations.
Figure 1 and the descriptions below highlight some features of the Fire Command
Center.
2 XR Fire Control Panel User Guide | Digital Monitoring Products, Inc.
The COMMAND key allows you to advance through the displays or User Menu. You
can also use the COMMAND key to complete a data entry function.
The Command Key
The Back Arrow Key
Use the Back Arrow key to go back through displays while operating your system.
Press the Back Arrow key to back up through the list of User Menu functions or to
make a correction by erasing the last character you entered.
The Select Keys
There are four keys under the display called the Select Keys. They allow you to
choose what to do by pressing the Select Key under choices being shown in the
display.
Data Entry Keys
These keys allow you to enter your user code and other information into the
system.
Digital Monitoring Products, Inc. | XR Fire Control Panel User Guide 3
Power LED
This LED remains on steady when both AC and battery input are good. The LED
turns o when AC input is low. The LED flashes when battery input is low.
Trouble LED
This LED turns on when any trouble displays in the status list, such as AC, battery,
phone line, transmit, ground fault, NAC, or any zone trouble. This light is o when
no trouble displays in the status list.
Alarm LED
This LED is on when any alarm currently displays in the status list. This LED is o
when no alarm currently displays in the status list.
Status LEDs
To enter an alpha character, press the key that has that letter written below it. The
keypad displays the number. Next, press the Select Key that corresponds to the
location of the letter under the key. Pressing a dierent Select Key changes the
letter. Press another number is pressed to continue.
Entering Alpha Characters
4 XR Fire Control Panel User Guide | Digital Monitoring Products, Inc.
To enter a space in an alpha entry, press the 9-digit key followed by the third
Select Key. The three characters on the 9-digit key are Y, Z, and space. You can
also enter the following characters: –(dash), . (period), *(asterisk), and #(pound
sign) using the 0(zero) key and the four Select Keys from left to right. See the
table below:
KEY NUMBER SELECT KEY 1 SELECT KEY 2 SELECT KEY 3 SELECT KEY 4
1 A B C (
2 D E F )
3 G H I !
4 J K L ?
5 M N O /
6 P Q R &
7 S T U @
8 V W X ,
9 Y Z space _
0 - . * #
Entering Non-Alpha Characters
Autres manuels pour XR150FC Series
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels DMP Electronics Panneau de contrôle
DMP Electronics
DMP Electronics XR150 series Manuel utilisateur
DMP Electronics
DMP Electronics XR200 Manuel utilisateur
DMP Electronics
DMP Electronics XR2400F Manuel utilisateur
DMP Electronics
DMP Electronics XR5FC Mode d'emploi
DMP Electronics
DMP Electronics XR550 series Manuel utilisateur
DMP Electronics
DMP Electronics XR6 COMMAND PROCESSOR Manuel utilisateur
DMP Electronics
DMP Electronics XT Series Fiche technique
DMP Electronics
DMP Electronics XTLN Manuel utilisateur
DMP Electronics
DMP Electronics XR100 Mode d'emploi
DMP Electronics
DMP Electronics XR550INT Series Manuel utilisateur
DMP Electronics
DMP Electronics XR20ATM Manuel utilisateur
DMP Electronics
DMP Electronics 630F Guide d'installation
DMP Electronics
DMP Electronics XTLplus Manuel utilisateur
DMP Electronics
DMP Electronics XTLN-WiFi Manuel utilisateur
DMP Electronics
DMP Electronics XT50 Series Manuel utilisateur
DMP Electronics
DMP Electronics XR150FC Series Manuel utilisateur
DMP Electronics
DMP Electronics XT Series Mode d'emploi
DMP Electronics
DMP Electronics XT30 Series Manuel utilisateur
DMP Electronics
DMP Electronics XT Lite Manuel utilisateur
DMP Electronics
DMP Electronics XR200 Mode d'emploi
