Divis CH 03101 Manuel utilisateur
*Lens is not included
CH 03101
Day & Night Box Camera
Diagram
Caution
1. Do not attempt to disassemble the camera.
In order to prevent electric shock, do not remove screws or cover.
2. Handle the camera with care.
The camera could be damaged by improper handling or storage
3. Do not expose the camera to rain or moisture, or try to operate in wet
areas.
Take immediate action if the camera becomes wet. Turn the power off and
request service to qualified personnel. Moisture can damage the camera and
also create a risk of electric shock.
4. Do not use strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when dirty. In case the dirt is hard to
remove, use a mild detergent and wipe gently.
5. Never point the camera toward the sun.
Whether the camera is used outdoor or not, never point it toward the sun. Use
with caution when operating the camera in the vicinity of spot lights or other
bright lights and light reflecting objects.
6. Do not operate the camera beyond its temperature, humidity, or power
source ratings.
Do not use the camera in an extreme environment where high temperature or
high humidity exists. Use the camera under conditions where temperatures are
between 14 F~122 F (-10 C~+50 C), and humidity is below 85%,
SA 1965
The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be sufficient magnitude to constitute a risk of electric shock to persons.
To prevent electric shocks and risk of fire hazards,
DO NOT use other than specified power source.
CAUTION:
!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture. The symbol is intended to alert
the user to the presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
SA 1966
!
WARNING
CAUTION
This equipment has been tested and found to comply with the limits for a Class A. Digital
device. Pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with
the instruction manual, it may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at own expense.
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority to operate the equipment.
oooo
104.9
POWER
ENTER
R
L
D
U
CLASS2 ONLY
Non polarity
DC 12V
VIDEO
63.9
55.5
Mounting hole
: 1/4"-20UNC(20Thread)
L-4.5mm±0.2mm
Hexagon wrench C mount ring
: 1.27mm L type
Accessories
Lens Connection
Manual iris lens
1. Before mounting a lens, please check whether it is a C or CS mount lens
2. CS mount lens : After removing the protective rubber, attach the lens
3. C mount lens : Before installing the lens, attach C mount ring to the camera
4. Set the lens mode to manual
Auto iris lens
1. Attach a DC lens like the manual lens connection
2. Connect the lens plug to the auto iris connection on the side of the camera
3. Set the lens mode to DC by OSD
POWER
ENTER
R
L
D
U
CLASS2 ONLY
Non polarity
DC 12V
VIDEO
Setup for Camera Function
1. Function setting combination
ENTER : Display the menu and function
LEFT : Move to left
RIGHT : Move to right
UP : Move to up
DOWN : Move to down
2. OSD Menu
ENTER button : Press 'ENTER' button to go to the menu
UP & DOWN button : Press 'UP' or 'DOWN' button to go up or down
LEFT & RIGHT button : Press 'LEFT' or "RIGHT' button to go left or right
NOTICE
' ' Signal means that you can go to the sub menu in case of pressing
"ENTER" button.
①
②
③
④
⑤
①
②
③
Special Menu Menu
Camera Title Off Off / On
OSD Menu Structure 2
Default Set
RS485
1 ~ 255 Selectable
Off / On
2400 / 4800 / 9600 / 19200 / 38400 / 57600
Cam ID
ID Display
Baudrate
Motion
On : Area Select (1~4)
Area Display (On/Off)
Left/Right (0~100)
Width (0~100)
Top/Bottom (0~100)
Height (0~100)
Sensitivity (0~40)
Motion View (Off/On)
Off
Sync
INT
INT
Privacy
On : Area Select (1~8)
Area Display (On/Off)
Left/Right (0~100)
Width (0~100)
Top/Bottom (0~100)
Height (0~100)
Color (0~15)
Off
Language
Korean/English/Japanese/Chinese
English
Return
Return to the SETUP menu-
D-Effect
Freeze : Off
Mirror : Off
D-Zoom : Off
Gamma : 0.45
Neg. Image : Off
On / Off
Off / Mirror / V-Flip / Rotate
On (D-Zoom x 32 / Pan 100 / Tilt 100) / Off
0.05 ~ 1.0 Selectable
Off / On
Return
Setup Menu Menu
Lens DC DC / Manual
Exposure
Shutter : -
Brightness : -
AGC : Middle
Sens_up : Auto
BLC : Off
DWDR : Off
Shutter : FLK, 1/60 ~ 1/100000, Manual
Brightness: 0 ~ 100 Level Selectable
Off / Low / Middle / High
Off / Auto (2 ~ 256 Level)
Off / BLC / HSBLC
Off / Indoor / Outdoor
Return
OSD Menu Structure 1
Default Set
White Bal
ATW / AWB / AWC / Manual / Indoor / Outdoor
Manual(R Gain : Level adjust / B Gain: Level adjust)
ATW
Day/Night
Auto : Delay / S-Level / E-Level
(S-Level : Change point to B/W,
E-Level : Change point to color)
B/W : Burst Off/On
Color : -
Auto
3DNR
On(Limit : 0 ~ 100 Level Selectable) / OffOn
Special
(Structure 2)
Refer to the
next Table
Reset
Set a manufacture state
-
Exit
Saves all the SETUP Menu and then exits-
Adjust
Sharpness:
Blue:
Red:
0 ~ 31 Level Selectable
0 ~ 100 Level Selectable
0 ~ 100 Level Selectable
Function Condition
Feature
Day & Night
BLC
DWDR
Blemish Compensation
Sens-up
OSD Language
Motion Detection
3DNR
Digital Zoom
Privacy
Mirror(H-REV)
Flip(V-REV)
Freeze
Sharpness
Auto(Electric D&N)/Color/BW
Off/HSBLC/BLC(64 Areas Selectable)
Off/Indoor/Outdoor
256 Point(Even 128 point, Odd 128 point)
Off/Auto(Selectable limit x2 ~ 256)
Korean/English/Japanese/Chinese
On/Off (4 Areas Selectable)
Off/On (0 ~ 100 Level Adjustable)
On( x 32)/Off
On/Off(8 Zone)
On/Off(Horizontal)
On/Off(Vertical)
On/Off
Level Adjustable
Day & Night Box Camera
1/3" Sony SUPER HAD II CCD
768(H) x 494(V)
6.35μm(H) x 7.4μm(V)
HORI. Color 580 TV Line, B/W : 600 TV Line
NTSC
Internal
2:1 Interlace
15.734 KHz
INT : 59.94
1.0 Vp-p (Sync. Negative) Termination 75
= 0.45 typ.
0.1 Lux ( at F1.2 )
50dB or More (AGC OFF, Weight ON)
ATW / AWB / AWC / MANUAL / INDOOR / OUTDOOR
Off / Low / Middle / High
1/60 ~ 1/100,000 sec
150mA
Regulated DC 12V
±
15%
Non polarity
-10 ~ 50 °C / 30% to 80% RH
-20 ~ 60 °C / 20% to 90% RH
Built in EMI Suppression filter
63.9mm(W) X 55.5mm(H) X 104.9(D)
Approx. 450 g
Model CH 03101
Specification
Type
Image Sensor
Effective Pixel
Cell Size
Resolution
TV Type
Sync. Type
Scanning System
Scanning Frequency H.
Scanning Frequency V.
Video Out
Gamma Characteristic
Min. Illumination
S/N Ratio
AWB
Gain Control
Shutter
Current Consumption
Supplied Voltage
Reverse Polarity Protection
Operation Temp / Humidity
Preservation Temp / Humidity
Noise Protection
Dimension
Weight
Troubleshooting
If you have a trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
The image does not
appear on the screen.
Check the power source for the monitor and camera
and assure that the voltage and polarity are properly
connected and being supplied correctly.
The image on the
screen is dim.
Check if the lens is stained. If dirty, clean the lens
with a soft, clean cloth.
Adjust the Back Focus of the lens again.
The surface of the
camera case is hot and
a black line appears on
the screen.
Check if you have connected the camera to a proper
power source and if there is no problem with the power,
turn the unit off immediately and seek assistance from
our After Service department.
Check if the camera is pointed toward the sun or a
fluorescent lamp.
Adjust the angle or location of the camera if too much
light is coming into the screen.
The screen blinks a lot.
The image on the screen
is dark.
Adjust the contrast feature of the monitor
Adjust DC level
±±
Ȗ
EXT : (EXT IS NOT SUPPORTED)
(RS485 IS NOT
SUPPORTED)
Hz
Autres manuels Divis Appareil photo numérique
