DITEC PASP Manuel utilisateur

PASP

* Other use of the device outside of the permitted purpose can not be guaranteed by the manufacturer.

TECHNICAL SPECIFICATIONS

DESCRIPTION

ENGLISH

PASSIVE INFRARED SENSOR FOR AUTOMATIC

DOORS*

Speciﬁcations are subject to changes without prior notice.

Measured in speciﬁc conditions.

Technology :

Optical characteristics:

Maximum Detection area (mounting height: 2.2m):

Minimum Detection area (mounting height: 2.2 m)

Detection mode:

Detection speed:

Light indicator:

Warm up time:

Hold time:

Response time:

Power supply:

Frequency:

Power consumption:

Connection:

Recommended cable section (terminal block):

Standard output:

Max. contact voltage:

Max. contact current:

Max. switching power:

Mounting height:

Temperature range:

Dimensions:

Sensor:

Entrematic PASP:

Color (Sensor-PASP):

Length of cable:

Conformity:

passive infrared and microprocessor

P.I.R. with 4 elements, 15 lenses with full independent masking possibilities

2.5 m (W) x 1.5 m (D)

0.5 m (W) x 0.5 m (D)

motion

0.1 to 1.5 m/s

1 red LED:ﬂashes for a few seconds after power-on

LED lights up: sensor detects motion

10 s

0.5 s ou 2 s

< 200 ms

12 VDC - 10% à 24VDC +30% /12 to 24 V AC ±10%

50/60 Hz

< 1 W

terminal block

< 0.5 mm²

relay (free potential contact)

60 V DC / 42 V AC

1A (resistive)

30W (DC) / 42 VA (AC)

3 m max

from -30 °C to +55 °C

101 mm (W) x 41 mm (H) x 27 mm (D)

121 mm (W) x 51 mm (H) x 40 mm (D)

anthracite grey

2.5 m

EN 61000-6-2; EN 61000-6-3; EN 50581

User’s Guide for product version 0202 and higher

See product label for serial number.

PLEASE KEEP FOR FURTHER USE

DESIGNED FOR COLOUR PRINTING

1. Sensor ﬁxing

screw (black)

2. LED

3. DIP-switch

4. Lens

5. Terminal block

6. Bracket

7. bracket

ﬁxing screw

(aluminium)

PASP

OPENING AND CLOSING THE SENSOR

MOUNTING THE SENSOR

To open the sensor, insert a screwdriver in the hole

under the bracket cam.

Consider the position of the guide pin when

closing the sensor.

Insert the bottom of the front cover to the bottom

clip of the base and push to close the sensor.

To remove the cover, insert a screwdriver as shown

(left) or pinch off both sides of the front cover (right).

1. Stick the template to the internal proﬁle.

2. Drill the 2 holes.

3. Fix the brackets to both sides of the sensor with the 2 aluminum screws.

4. Fix the sensor, with the connector facing you, to the proﬁle with the 2

black screws.

5. Make the cut-out in the door proﬁle.

6. Connect the sensor using the cable (See p. 1 for wiring).

7. Adjust the tilt angle using the brackets.

1. Stick the template to the wall.

2. Drill the 2 holes to ﬁx the sensor and the hole for the cable.

3. Open the sensor and cut out a wire opening footprint.

4. Fix the sensor to the base with the 2 aluminum screws supplied

with the PASP.

5. Connect the sensor using the cable.

6. Fix the sensor with the 2 black screws and close the sensor.

SENSOR

SENSOR FRONT COVER

1. Stick the template to the ceiling and cut out the hole.

2. Clip the sensor on the FCA and ﬁx it with the 2 washers and the 2

aluminum screws.

3. Connect the sensor using the cable.

4. Insert the complete assembly into the ceiling and ﬁx it using the 2

long, black screws.

PASP

2 3

DIP SWITCH SETTINGS

OFF

DIP SWITCH #1 DIP SWITCH #2 DIP SWITCH #3

Sensitivity high

Sensitivity low

(mounting height< 2.2m)

Passive output (NC)

Active output (NO)

Hold time: 2 s

Hold time: 0.5 s

The drawings show the maximum sensing ﬁeld dimensions. If you install the PASP without accessories, you can move

the sensing ﬁeld position by tilting the sensor to select the required vertical tilt angle. Otherwise, this adjustment is

not possible.

To adjust the sensing ﬁeld, use the

masking lens. To tailor the sensing

ﬁeld, cut the segments.

Use the guide pins to insert the

masking lens on the front cover.

Position the screwdriver as shown

to remove the masking lens.

SENSING FIELD SETTINGS

EXAMPLES: door threshold

door threshold

DETECTION AREA

NO DETECTION

DETECTION AREA

FRONT VIEW

FLAT VIEW

Door threshold

height

ASSA ABLOY Entrance Systems AB - Lodjursgatan 10 - SE-261 44 Landskrona - Sweden - www.ditecautomations.com

ASSA ABLOY Entrance Systems AB hereby declares that the PASP is in conformity with the basic requirements and the

other relevant provisions of the directives 2014/30/EU and 2011/65/EU.

Landskrona, January 2021 Matteo Fino, authorized representative and responsible for technical documentation.

The complete declaration of conformity is available on our website.

TROUBLESHOOTING

This product should be disposed of separately from unsorted municipal waste

INSTALLATION TIPS

The sensor must be ﬁrmly

fastened in order to avoid

vibrations!

When mounting the

PASP, make sure you apply the

brackets before tightening

the screws.

Always use the aluminium

screws to fasten the

accessories and the black

screws to ﬁx the sensor.

Using the wrong screws could

damage the sensor!

The door remains

closed. The LED is OFF.

The door will not open

and the LED lights up.

The door opens when

no detection occurs

and closes during

detection.

The sensing ﬁeld does

not correspond to your

requirements.

The detection is very

bad.

The sensor power is off.

The mode of the relay output

is not correct.

The cut of the masking lens

is wrong.

The sensor might be installed

upside down.

The wiring of the relay

output is not connected

correctly.

Check the wiring and the power supply. check the

supplied voltage.

Check the relay wiring.

Change the position of dip-switch 2.

Cut out a new lens to meet the required sensing

ﬁeld size.

Check if the sensor is installed with its connector

facing you.

©ASSA ABLOY Entrance Systems AB I Original instructions | 47.0463 / V1 - 05.21

Ce manuel convient aux modèles suivants

Autres manuels DITEC Système d'ouverture de porte

DITEC

DITEC DAS200TRF Manuel utilisateur

DITEC

DITEC DAS200T Manuel utilisateur

DITEC

DITEC DAS107PLUS Manuel utilisateur

DITEC

DITEC DOR Manuel utilisateur

DITEC

DITEC DOD Series Mode d’emploi

DITEC

DITEC PID24 Manuel utilisateur

DITEC

DITEC DAS107 Manuel utilisateur

DITEC

DITEC DAB105 Manuel utilisateur

DITEC

DITEC 94 Manuel du système

DITEC

DITEC DAS200 Manuel utilisateur

DITEC

DITEC DAS200T Manuel utilisateur

DITEC

DITEC 0DT848 Guide de l'utilisateur

DITEC

DITEC BIS O Manuel

DITEC

DITEC CIVIK Series Manuel

DITEC

DITEC Sprint Manuel utilisateur

DITEC

DITEC Sprint Manuel

DITEC

DITEC ENTREMATIC HA9 Manuel utilisateur

DITEC

DITEC Flash C Guide de l'utilisateur

DITEC

DITEC DAS107PLUS Manuel utilisateur

DITEC

DITEC DAB305 Manuel utilisateur

DITEC

DITEC DAS900FM Manuel utilisateur

DITEC

DITEC entrematic HA8-LP Manuel de service

DITEC

DITEC Sprint Manuel utilisateur

DITEC

DITEC Entrematic ENERGY 49E Guide de l'utilisateur

Manuels Système d'ouverture de porte populaires d'autres marques

Pamex

Pamex KT-INP35 Manuel utilisateur

Label

Label NEPTIS/LE Manuel utilisateur

Cal-Royal

Cal-Royal N-F77CVR Manuel utilisateur

Scrigno

Scrigno OPEN1000 Manuel utilisateur

TriMark

TriMark UM 34 Manuel utilisateur

BFT

BFT WIND RMB 130B 200 Manuel utilisateur

Alecto

Alecto ADI-250 Manuel utilisateur

Besam

Besam Swingmaster MP Mode d’emploi

CRL

CRL SENIOR PRIMA Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 1431 Series Manuel utilisateur

GAL

GAL MOVFR Fiche technique

Olide

Olide 120B Manuel utilisateur

Normstahl

Normstahl IDO7 Manuel utilisateur

Häfele

Häfele Finetta T 70 VF Manuel utilisateur

AGS

AGS D-PL Manuel

Stanley

Stanley MA900ñ Instructions d'installation

WITTUR

WITTUR Hydra Plus UD300 Manuel

Alutech

Alutech TR-3019-230E-ICU Instructions d'installation et d'utilisation