distianert DH-8 Manuel utilisateur
With its highly sensitive 120° Passive Infra-Red (PIR) sensor, the
camera detects the sudden change of ambient temperature caused by
moving game in a region of interest (ROI), and triggers to take
pictures/videos, so you don’t miss what is walking in front of your
camera.
Features
•Programmable 1, 3, 5, 8 or 12 Megapixel high-quality resolution.
•Infrared night vision LEDs for flash range as far as 65 feet.
•In “Cam + Video” mode, camera takes both pictures and video at
every trigger event.
•Impressively quick trigger time (0.2-0.6 second, Pre boot 0.2
second).
•Unique side Prep Sensor design provides wider sensing angle
and enhances camera’s response speed.
•In Time Lapse setting, the camera automatically and constantly
takes pictures/videos at specified interval. This is very useful
when observing plants flowering, birds building nest, or when
monitoring unattended properties such as parking lots.
•With Timer setting on, the camera can be programmed to only
work in specified period every day. This feature can work
together with Time Lapse feature.
•Serial Number setting enables you to code locations in the
photos. This helps multi-camera users identify the location when
reviewing the photos.
INTRODUCTION
•Ultra low standby power consumption. Extremely long in-field life
(in standby mode, up to 8 months with 8 x AA batteries).
•Built-in 2.4" TFT color display to review images and videos.
•Date, time, temperature and moon phase can be stamped in the
pictures.
•Backpack-looking tree grabber makes mounting and aiming a
snap.
•Perform in the most extreme temperatures from -4°F to 140°F.
•Compact size (5.3 x 3.5 x 3.0 inches). Well designed to deploy
covertly.
•Lockable and password protected.
•IP56 water resistance.
Application
•Trail camera for hunting.
•Animal or event observation.
•Motion-triggered security camera, for home, office and
community.
•All other indoor/outdoor surveillance where invasion evidence
needed.
INTRODUCTION
CAMERA OVERVIEW
1. Up button
2. Right button
3. Shot button
4. Ok button
5. Left button
6. Menu button
7. Replay button
8. Down button
9. SD Card slot
10. AV jack
11. USB jack
12. OFF
13. Test
14. ON
15. Infrared LEDs
16. Lens
17. Front motion
sensor
18. Side motion sensor
19. Display screen
19
CAMERA OVERVIEW
SIMPLE TO USE THIS CAMERA
①Install Batteries ②Install SD Card
③Switch to TEST ④Press MENU to setting
⑤Format memory card ⑥Reset to factory setting
SIMPLE TO USE THIS CAMERA
⑦Set The Date & Time ⑧Switch to ON to use
SIMPLE TO USE THIS CAMERA
Power supply
Batteries Installation
Open the camera by unlocking latch firstly. The battery compartment
is the right part of the camera. Open the protective cover of the battery
compartment and insert 4 x 1.5 V LR6/AA batteries into the battery
slots. Make sure to insert each battery with correct polarity (+ and -
end against the long spring of each battery slot). To increase the
operating time, you can use 8 x 1.5 V LR6/AAbatteries. When using 4
batteries, they all should be installed in the top 4 slots or in the bottom
4 slots.
Note:
• NEVER INSTALL DIFFERENT TYPES OF BATTERIES or NEW
AND OLD BATTERIES in the product at the same time.
• Anytime you load or unload batteries, make sure that the camera is
OFF. If using external power source, do not remove internal batteries.
Using an External Power Source
Optionally, you can connect an external 6V DC power source to the
‘DC In’ jack at the bottom of the camera. The power connector is a
3.5x1.35 mm coaxial DC power plug with positive ‘tip’ (inside pin)
polarity. Leave internal batteries in the camera during use.
BEFORE OPERATION
Inserting the SD Card
The camera uses a SD (Secure Digital) memory card to save photos
(in .jpeg format) and/or videos (in .AVI format). SD cards up to a
maximum 32 GB capacity are supported.
Insert the SD card (with the camera’s power switch in the OFF
position) before beginning to operate the camera. Don’t insert or
remove the SD card when the power switch is in the ON position.
Before inserting the memory card, please open the front cover and
make sure that the write-protect switch on the side of the card is ‘OFF’
(NOT in the “Lock” position).
• Insert the SD card into the card slot. A “click” sound indicates that the
card is installed successfully. If the wrong side of the card is facing up,
you will not be able to insert it without force-there is only one correct
way to insert cards.
• To take out the SD card, just gently push in the card (do not try to pull
it out without pushing in first). The card is released from the slot and
ready to be removed when you hear the click.
Note:
• Be sure the camera’s power is switched OFF before inserting or
removing SD cards or batteries.
• Camera will not operate without an SD memory card installed.
BEFORE OPERATION
Mode Switch
There are three basic operational modes:
• OFF mode: Power switch in the OFF position.
• ON mode: Power switch in the ON position (LCD screen is off.)
• TEST mode: Power switch at TEST position (LCD screen is on).
OFF Mode
The OFF mode is the “safe” mode when any actions must be taken,
e.g. replacing the SD card or batteries, or transporting the device.
ON Mode
The camera will take photos or videos automatically (according to its
current parameter settings) when it is triggered by the PIR sensor’s
detection of activity in the area it covers.
TEST Mode
In the TEST mode you can check and change the settings of the
camera with the help of its built-in LCD. These settings, found in the
TEST Menu, let you change the photo or video resolution, interval
between photos, switch the time imprint on, etc.
Change Setting in TEST Mode
The main purpose of the TEST mode is to allow you to change the
settings of the camera’s parameters so your trail camera operates
exactly the way you want it to.
CAMERA OPERATION
Slide the mode switch to TEST position to start the test mode.
• Press the UP key, then press SHOT to take video for test.
• Press the DOWN key, then press SHOT to take photo for test.
• Pressing the MENU button, the setup menu will be shown on the
LCD.
• Press the UP or DOWN key scrolls to the next or previous
parameter.
• Press the RIGHT or LEFT key to change the setting.
• Press the OK button to save the new setting.
• Press the MENU button to exit the SETUP menu.
Mode
Photo: Capture photos with motion detection.
Video: Capture video clips with motion detection.
Photo + Video: Capture both photos and video with motion detection.
Photo resolution
Set resolution for still photos. We recommend the resolution 5M.
Options: 1 MP, 3 MP, 5 MP (preset), 8 MP or 12 MP.
Photo series
Selects how many photos are taken in sequence per trigger. In
addition to single shot mode (1 photo), you can take “2 photos in
series” or “3 photos in series”.
CAMERA OPERATION
Table des matières
Langues :
Autres manuels distianert Appareil photo numérique
