Displays2go IPDTBL Manuel utilisateur

iPad IPDTBL

Assembly Instructions

iPad Podium WARNING – large

base plate is heavy

(7.5kg).

Carefully position base

plate over 8-way post

and align 4 off fixing

holes to threads of

post (ensuring the

countersunk holes are

uppermost). Insert and

tighten 4 off base plate

screws to secure.

Carefully lay assembled

base and post

horizontally on floor.

NB – If you are

not using cable

management for

charging, please

carefully stand base

and post upright and

proceed to stage 7.

WARNING – Dome-headed

chrome nuts behind enclosure

housing must not be adjusted.

Feed figure-8 head of power lead through

base until it protrudes from top of post.

Stand base and post upright ensuring

lead is kept clear of foot pads.

Plug figure-8 head into USB Power

Adapter (supplied with Apple iPad).

Position black mains cable into internal post channel and carefully slide USB

Power Adapter down below the top of the post.

Align 4 holes of aluminium plate and

acrylic podium top, with countersunk

holes uppermost, with threaded holes

in post

Loosely Insert 2 screws through aligned

diametrically opposite holes. Fully tighten

1 screw using hex key provided before

removing second screw.

Unlock the iPad enclosure by inserting

key into security lock and rotate

‘QUARTER TURN ONLY’ clockwise or

counter-clockwise through 90 degrees

which releases the locking pin. Return

key back to original position

to remove.

If you are not using cable

management for charging, please

proceed to stage 13.

Lift fascia out of enclosure. Insert cable (supplied

with Apple iPad) allowing 10cm to remain “free” at

charge/sync connector end by gently pressing into

retaining moulding.

Feed USB end of charge/

sync cable through

middle of enclosure,

below pin, so it just

protrudes from bottom

of support column.

11 12

Plug cable into USB Power

Adapter below podium top

and plate.

Align holes of the iPad holder to the

post fixings. Insert and tighten 2 screws

to secure. Rotate iPad holder through

90º, aligning remaining 2 holes to post

fixings. Insert and tighten final screw to

secure (in diametrically opposite hole

from tightened screw in stage 8).

Plug charge/sync cable into iPad and

place inside enclosure, gently press

all four corners of iPad down into

mouldings to hold.

NB – If you are not using cable management for charging, unlock the iPad enclosure by

inserting key into security lock and rotate ‘QUARTER TURN ONLY’ clockwise or counterclockwise

through 90 degrees which releases the locking pin. Return key back to original position to remove.

Lift fascia out of enclosure, and place iPad inside, gently pressing all four corners down into

mouldings to hold.

Replace fascia

and depress lock

button to secure

enclosure.

Autres manuels Displays2go Support et étagère

Displays2go

Displays2go MSHWL Series Manuel utilisateur

Displays2go

Displays2go IPPROEVRF Manuel utilisateur

Displays2go

Displays2go SMAWRDCSC Manuel utilisateur

Displays2go

Displays2go TVSTNDLBK2 Manuel utilisateur

Displays2go

Displays2go TVJT321G1 Manuel utilisateur

Displays2go

Displays2go IPDTBL3 Manuel utilisateur

Displays2go

Displays2go TVM110B Manuel utilisateur

Displays2go

Displays2go LTCEIL20 Manuel utilisateur

Displays2go

Displays2go MGWLSBK Manuel utilisateur

Displays2go

Displays2go CDSTAND2BK Manuel utilisateur

Displays2go

Displays2go RD209O0SV Manuel utilisateur

Displays2go

Displays2go PEDLEDSV Manuel utilisateur

Displays2go

Displays2go RCCDIGITALS Manuel utilisateur

Displays2go

Displays2go LTMLT2AV1 Manuel utilisateur

Displays2go

Displays2go TVTRUSS74 Manuel utilisateur

Displays2go

Displays2go LM3255TLT Manuel utilisateur

Displays2go

Displays2go TVSTN01 Manuel utilisateur

Displays2go

Displays2go PROMXMN Manuel utilisateur

Displays2go

Displays2go DSTANDBK Manuel utilisateur

Displays2go

Displays2go MNTW803L Manuel utilisateur

Displays2go

Displays2go WXNTVGBO1 Manuel utilisateur

Displays2go

Displays2go SM3TWDR Manuel utilisateur

Displays2go

Displays2go WL3SDSG Manuel utilisateur

Displays2go

Displays2go DGMLTSBK Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur