Discount Fence PRX-320 Manuel utilisateur

PRX-320 Waterproof Proximity Access

Operating Instructions and Installation Manual

Contents

I. SPECIAL FEATURES 1

II. FRONT PANEL 1

III

. INSTALLATION PROCEDURES AND PROXIMITY CARD TYPES 2

IV. SETTING MODE AND FUNCTIONS 3

1. Add Proximity Card(s) 3

2. Delete Proximity Card(s) 4

3. Add / Change User Pass Code 4

4. Door Lock Time Setting 5

5. Setting Door Access Entry Mode 5

6. Batch Registration (Adding Sequential Card Series) 6

7. Anti-Tamper Output 6

8. Change System Code 7

9. Delete User Pass Codes 7

10. Delete All Proximity Cards 8

11. Door Access Using System Code 8

V. INSTALLATION OF PROXIMITY READER 9

1. Connections 9

2. Installation of electric lock and exit push button 10

3. Installation of door sensor, external relay and siren 11

I. PRECAUTIONS 12 13VII. ASSEMBLY INSTRUCTIONS

13Mounting steps 1 - 314Mounting steps 4 - 615Mounting step 716Optional Accessories

ST-320 Mode Setting

I. SPECIAL FEATURES:

1. Stand alone operation.

2. Front panel power-on indicator.

3. Four door opening modes. ENTRY MODE 1: Enter 4-digit Pass

Code only. ENTRY MODE 2: Proximity Card access only. ENTRY

MODE 3: Proximity Card plus 4-digit Pass Code. ENTRY MODE 4:

Proximity Card or 4-digit Pass Code

4. Programming Mode is protected by a 4-digit System Pass Code.

5. All Proximity Cards must be registered prior to use.

6. Maximum storage of 2000 cards.

8. Non-volatile memory protects against data loss.

II. FRONT PANEL AND PROXIMITY CARD TYPES

Indicator Lights Function

Green Status Light: Flashes to indicate panel key press. On to indicate

Programming Mode. Off in Normal Mode.

Yellow Status Light: Flashes to indicate unsuccessful access. On when

alarm is active.

Status Light Bar: Red - Power on in Normal Mode. Green – Indicates

successful access.

Ten Numeric Keys 0-9: Pass Code Entry and Programming Mode.

# Key: Confirmation Key

Clear or Escape Key

* Key:

Pg 1

Pg2

Proximity Cards

Proximity Cards will have either a single 8-digit number or an 8-digit number separated by a comma

and a 10-digit number in the center of the card. The ST-320 uses only the last 6-digits of the

8-digit number printed on either card type.

III. INSTALLATION PROCEEDURES

1 Refer to Appendix for mounting instructions.

2 Do not install Proximity Reader on or near metal objects, this will reduce the

effective range of Access Card detection.

3 Install the appropriate connector(s) to meet door access application requirements.

See the examples located on page 10 and 11.

4 Connect power to the reader.

5 The Status Light Bar should turn on Red and a single BEEP will sound. If the unit is

not attached to the mounting plate, the Yellow Status Light will be on, indicating an alarm

condition. The alarm is caused by the Anti-Tamper Switch on the rear of the unit.

IV. SETTING MODES AND FUNCTIONS **

Programming Mode Default System Pass Code: 4567 ** The system is factory preset for Entry

Mode 2 – Proximity Card Access Only. If another Entry Mode is desired, proceed to Function 5

prior to adding Proximity Cards or Pass Codes.

e on.

To enter into the Programming Mode, press the following keys in sequence:

*# 4 5 6 7 # After the last #in the sequence the system will

“Beep” once and the Green Status Light will b

The system will exit the Programming Mode automatically if no keys are pressed within 20 seconds.

The user can exit the Programming Mode any time by pressing the * key.

1. Add Proximity Card(s)

*** Placing the Proximity Card to be entered within the readers detection range instead of

entering the 6-Digit Card Code can also register single cards. This feature will only

function for individual card entry and not in the Batch Registration (Function 6) mode. Pg 3

2. Delete Proximity Card(s)

3. Add / Change User Pass Code

The System allows up to 8 different User Pass Codes to be programmed. Each Pass Code must

be a 4-digit number. The 4-digit Pass Code alone can allow door access (ENTRY MODE 1) or

be used in combination with a Proximity Card.

Pg 4

4. Door Lock Time Setting

This setting determines how long the electronic lock is active after door access. The time can be

set between 01 – 99 seconds (must use 2-digits). Set 99 seconds for toggle state (suitable for

security system).

5. Setting Door Access Entry Mode

There are four Door Access Entry Modes available in the ST-320. The unit is factory preset

for MODE 2, Proximity Card Access only.

ENTRY MODE 1: Enter 4-digit Pass Code only. (Enter 4-digit Pass

Code for door access) ENTRY MODE 2: Proximity Card access only.

(Present Proximity Card for door access) ENTRY MODE 3: Proximity

Card plus 4-digit Pass Code. (Present Proximity Card and enter 4-digit

Pass Code within 5 seconds) ENTRY MODE 4: Proximity Card or

4-digit Pass Code (Present Proximity Card or enter 4-digit Pass Code)

Pg 5

6. Batch Registration (Adding Sequential Card Series)

A sequential series of Proximity Cards can be quickly added to the system with this function.

Enter the lowest 6-digit Card Code followed by the amount of cards in the sequence. Enter

the amount of cards using a 4-digit value (75 cards = 0075)

7. Anti-Tamper Output

The system has an output dedicated to the detection of “Forced Entry” of the access door (door

contacts) and removal of the system from its mounting plate (Tamper Switch). The Function can

be set whether to include “Forced Entry” detection or not. The system Tamper Switch will always

activate the Anti-Tamper output. Enter “0” to include “Forced Entry detection. Enter “1” to

ignore.

Pg 6

. Change System Code

The factory default System Pass Code: 4567 The new

4-digit Pass Code value must be entered twice.

9. Delete User Pass Codes This function will delete

ALL 8 User Pass Codes.

Table des matières

Manuels Contrôleurs d'accès IP populaires d'autres marques

ZKTeco

ZKTeco SpeedFace-V5L Manuel utilisateur

Jantar

Jantar REX A-1-9 Manuel utilisateur

2N Access Unit Feuille d'instructions

Kedacom

Kedacom KSCA120 Series Manuel utilisateur

H3C

H3C WX2880X Manuel utilisateur

G4S

G4S S870-EX Mode d’emploi

PRASTEL

PRASTEL M2000PE Manuel utilisateur

Allegion

Allegion interflex IF-281 Cylinder Manuel utilisateur

TECOM

TECOM TS1067E Manuel utilisateur

Fermax

Fermax Memokey 100C Guide de l'utilisateur

Fermax

Fermax CITYLINE MEMOKEY Mode d’emploi

Software House

Software House iSTAR Pro 2U RM Mode d’emploi

AKCP

AKCP SP+ Manuel utilisateur

Bpt

Bpt HNA/102 Manuel utilisateur

Civintec

Civintec CV9601T-T-1F Manuel utilisateur

BioMax

BioMax N-X90W Manuel utilisateur

ZKTeco

ZKTeco OP-200 Manuel utilisateur

FingerTec

FingerTec s-Kadex Manuel utilisateur