Directed DS3+ Manuel utilisateur

INSTALLATION GUIDE

DS3+ / DS4+

2015 Toyota Sienna (Smart Key). 933.TL2 4.12.193.2

This product is intended for installation by a professional installer only! Attempts to install this

product by a person other than a trained professional may result in severe damage to a vehicle’s

electrical system and components.

Introduction 3

Vehicle function compatibilities 3

Pre-installation and application warnings 4

OEM remote starter detection 4

Installation 6

Wiring diagram with T-Harness (THTON6) 6

Wiring diagram 7

Locating components in the vehicle 8

Vehicle connections 9

Connecting the module 12

Important! 12

8556T Temperature Sensor 12

8504D Combo Sensor 12

RF Systems 13

When used in conjunction with SmartStart 13

D2D port configuration 13

Manual Transmission 14

Module programming 15

(For security-only programming, see next section.) 15

Module programming for security-only installations 16

LED diagnostics and troubleshooting 17

Soft reset 19

Hard reset 19

Learning the Tach (not needed with Virtual Tach) 20

Initializing Virtual Tach (not needed with hardwired or data tach applications) 20

Limited lifetime consumer warranty 21

Quick reference guide 22

Contents

3933.TL2 4.12.193.2 2015 Toyota Sienna (Smart Key)

Introduction

DS3+ is a complete solution for remote start, security (when security features are enabled) and bypass. This guide provides

information on the installation of the module as a digital solution. Please refer to www.directechs.com for more information about

which conﬁguration is best for your application.

Warning! This module can be conﬁgured using the web tool located at www.directechs.com. The DS3/DS3+ module is not

equipped with Bluetooth, therefore the blue LED will not ﬂash during module programming or when performing a soft or hard reset.

DS4+ is a complete solution for remote start, security (when security features are enabled), bypass, and features

built in Bluetooth 4.0 allowing you to conﬁgure and control your system. This guide provides information on the

installation of the module as a digital solution. Please refer to the DirectLink application or www.directechs.com

for more information about which conﬁguration is best for your application.

Warning! This module is designed to be conﬁgured using the DirectLink application for mobile devices,

however it can also be conﬁgured using the web tool located at www.directechs.com. To download the DirectLink mobile

application, please visit the Google Play or Apple store.

Vehicle function compatibilities

This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.

Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.

Auto Headlamp Shutoff

Arm Factory Security

Disarm Factory Security

Door Lock Control

Door Unlock

Driver Priority Unlock

Sliding Door Control Driver

Sliding Door Control Passenger

Trunk / Hatch Release

Control of aftermarket alarm with OEM remote

* Fuel Level

* Odometer

Immobilizer Bypass-Data No Key Req'd

3x LOCK START (Start control using OEM Remote)

3x LOCK STOP (Stop control using OEM Remote)

Accessory Activation

Ignition Activation

SmartStart

Start (Crank) Activation

Tach / RPM Output

Entry Monitoring ALL Door Pins

Entry Monitoring Hood Pin

Entry Monitoring Trunk/Hatch Pin

Factory Alarm Trigger Monitoring

Brake Status (foot brake)

E-Brake Status

Ignition Status

4933.TL2 4.12.193.2 2015 Toyota Sienna (Smart Key)

Pre-installation and application warnings

Firmware notes: This section highlights important information for this speciﬁc ﬁrmware and will assist in

pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness

compatible THTON6 Keys required for

programming 1Keys required for

operation 0

Warning! No takeover feature is available on Push-to-Start vehicles.

The keyless and Smart Key will remain functional during remote start.

All Hybrid vehicles: for best results, set Engine Checking to OFF when ﬂashing.

If the vehicle is already equipped with an OEM remote starter, the installer must disconnect it before installing the DS4 plus

module, otherwise it will not program.

The optional Plug & Play THTON6 T-Harness is sold separately.

Important! All T-Harness wires NOT listed in the diagram are NOT required for the installation. Loose wires such as Siren

Output and Hood Input may need to be pulled from the tapped section of the T-Harness. Refer to the “Wiring diagram with

T-Harness” for more information on connections and installation instructions.

All T-Harness wires NOT listed in the diagram are NOT required for the installation.

Unless speciﬁed otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic

connector.

It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each

wiring diagram.

Refer to the "Vehicle connections" following the installation diagram.

General notes: This section highlights important information for this speciﬁc ﬁrmware.

[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin.

[2] The siren is ONLY required when enabling the security features during module ﬂashing.

[3] Connection required ONLY if Pit-Stop/Idle mode is desired.

[4] For Security Only Installations, refer to 'Locating components in the vehicle' for the optional starter disable connection.

5933.TL2 4.12.193.2 2015 Toyota Sienna (Smart Key)

OEM remote starter detection

If the vehicle has an active OEM remote starter it will program into convenience only (no immobilizer bypass). The reason for this

is to allow aftermarket security to be installed while keeping the factory remote starter active. If you wish for the interface to control

the remote start sequence, perform one of the following:

If the vehicle is equipped with an Add-On Lexus/Toyota OEM remote starter:

Some Lexus/Toyota vehicles may have an Add-On remote starter. If the OEM unit is installed, whether Active or Inactive, it MUST

be permanently disconnected, as both modules cannot coexist. Refer to 'Physical OEM remote start locations" in the chart below

and always physically inspect and disconnect any OEM remote starter before programming any Directed products.

Physical OEM remote start locations

Make Model OEM remote starter & connectors location

Toyota Venza (Smart Key) Behind glove box.

Lexus RX 450h (Smart Key) Behind glove box.

Lexus RX 350 (Smart Key) Behind glove box.

Toyota 4Runner (Smart Key) Behind glove box & passenger kick panel.

Toyota Sienna (Smart Key) Behind glove box & passenger kick panel.

Lexus HS 250h (Smart Key) Behind glove box.

Prius Prius (Smart Key) Under dash panel & driver kick panel.

Lexus CT 200h Behind glove box.

Lexus GX 460 (Smart Key) Behind glove box.

Toyota Prius V (Smart Key) Behind glove box.

If the vehicle is equipped with a BCM Enabled Lexus/Toyota OEM remote starter:

The vehicle does not have a physical remote starter and only one module can be programed at a time. In this case temporarily

disable the OEM remote start system using the following process:

1. Remove the fuse powering the OEM Remote Starter. See "OEM remote start fuse location"

2. Perform a "Soft reset" or "Hard reset".

3. Perform the "Module programming".

4. After programming is successful, re-insert the fuse powering the OEM Remote Starter.

OEM remote start fuse location

Make Model Fuse Location Fuse Name Fuse

Value

Lexus CT 200h (Smart Key) Engine room relay box, left side of engine compartment. MAYDAY 10A

Lexus GX 460 (Smart Key) Engine room relay box, left side of engine compartment. MAYDAY 7.5A

Lexus RX 350 (Smart Key) Engine room relay box, left side of engine compartment. MAYDAY/TEL 7.5A

Lexus RX 450h (Smart Key) Engine room relay box, left side of engine compartment. MAYDAY 7.5A

6933.TL2 4.12.193.2 2015 Toyota Sienna (Smart Key)

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

Refer to the

Optional starter disable

connection section for relay

and connection details.

Cut the Tan & Tan/Black loops labelled

CAN 1 and extend the wires coming

from the module side and connect them

to the CAN wires on the OBDII.

Wiring diagram with T-Harness (THTON6)

Diagnostic Connector OBDII

(connector side view)

HS CAN Low: White

or Red, pin 14

Steering Lock

(black 7-pin connector)

Main Body

ECU

Siren

Hood Pin

ENGINE

START

STOP

Black

connector

1214 11 10 8

(-) Push-to-Start Output: Lt. Blue/Black

(-) Hood Input: Gray

(+) Siren Output: Brown/Red

(-) Push-To-Start:

Blue or Lt. Green, pin 7

Body ECU Connector

(middle conn. left side

of steering column)

TL8

TL6

TL2

NOT USED

CONNECT the white 12-pin

connector to the 12-pin

connector labeled TL2.

(-) GWA Output: Blue/White

HS CAN High: Red or Violet, pin 6HS CAN High: Red or Violet, pin 6

Cut the

Dk.Green/Black

and Dk/Blue/Black

loops labelled

Lock/Unlock.

THTON6

(optional T-Harness)

8-pin White Connector

22-pin White Connector

12-pin Black Connector

HS CAN Low: Tan

HS CAN High: Tan/Black

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

22 812

4 2442

Slide to open

A module can also be used for

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

*Connectors color may

differ depending on

the T-Harness revision.

Engine Start Stop Switch

(black conn)

7933.TL2 4.12.193.2 2015 Toyota Sienna (Smart Key)

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

Refer to the

Optional starter disable

connection section for relay

and connection details.

Wiring diagram

1235 47 6

Diagnostic Connector OBDII

(connector side view)

HS CAN Low: White

or Red, pin 14

HS CAN High: Red or Violet, pin 6

Steering Lock

(black 7-pin connector)

BTX: Pin 16

Body ECU

(White or Black 30-pin

connector)

Main Body

ECU

1 7

2 8

16 28

(-) Parking Lights: Pin 30

BRX: Pin 4

Siren

Hood Pin

ENGINE

START

STOP

Black

connector

1214 11 10 8

(+) 12V: Pin 16

(-) SLP Output: Blue: 3

(-) Ground: Black: 10

HS CAN Low: Tan: 1

(-) Push-to-Start Output: Lt. Blue/Black: 10

(-) Parking Lights Output: Lt. Green/Black: 1

HS CAN High: Tan/Black: 2

Immo Data 1: Yellow/Black: 8

Immo Data 2: Orange/Black: 7

(+) 12V Input: Red: 6 & 12

(-) Hood Input: Gray: 21

(+) Siren Output: Brown/Red: 11

(-) SLP: Green or

Lt. Blue, pin 4

(-) Push-To-Start:

Blue or Lt. Green, pin 7

(-) Ground: Blue/Red: 2

(-) GWA Output: Blue/White: 2

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

22 812

4 2442

Slide to open

A module can also be used for

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

Engine Start Stop Switch

(black conn)

8933.TL2 4.12.193.2 2015 Toyota Sienna (Smart Key)

Locating components in the vehicle

(-) Ground When Armed (GWA) Output: Blue/White: 2

86 85

87a

Optional starter disable connection

Cut

Starter (conn. side)

Starter (veh. side)

(+) Ignition

Refer to the

Vehicle connections

section for wire and

connector details.

22 812

4 2442

When using an external relay, use a 1N4002 diode or larger.

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

1A diode [1N4002+ ]

9933.TL2 4.12.193.2 2015 Toyota Sienna (Smart Key)

Vehicle connections

The connection information listed below is specific to the 2015 Toyota Sienna (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes.

Data harness, 8-pin white connector (H1)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Connection

H1/1 Tan (Data) HS CAN Low OBD-Data Link Connector, white 16 pin plug, pin 14 data white Mandatory

H1/2 Tan/Black (Data) HS CAN High OBD-Data Link Connector, white 16 pin plug, pin 6 data red Mandatory

H1/3 Orange/Brown No Connection No Connection

H1/4 Orange/Green No Connection No Connection

H1/5 Lt. Green No Connection No Connection

H1/6 Violet/Brown No Connection No Connection

H1/7 Orange/Black (Data) Immo Data 2 Body ECU on dash fuse box, white 30 pin plug, pin 16 data blue (BTX) Remote Start

Only

H1/8 Yellow/Black (Data) Immo Data 1 Body ECU on dash fuse box, white 30 pin plug, pin 4 data black (BRX) Remote Start

Only

Analog input/output harness, 22-pin white connector (H2)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Connection

H2/1 Lt. Green/Black (-) Pk Light Output Body ECU on dash fuse box, white 30 pin plug, pin 30 - yellow Mandatory

H2/2 Blue/White (-) Ground When Armed (GWA) Output [2] Starter:

Power Management ECU behind glove box, white 30 pin plug,

pin 3

Ignition:

dash fuse box, white 40 pin plug (2F), pin 6

Must use a relay.

Must use a 1A 1N4002 or larger diode.

pink

red

Security Only

H2/3 Dk. Green/Black No Connection No Connection

H2/4 Red/White No Connection No Connection

H2/5 Brown/Black No Connection No Connection

H2/6 Brown/White No Connection No Connection

H2/7 White (+) No Connection No Connection

H2/8 Violet/Black No Connection No Connection

H2/9 Dk. Blue/Black No Connection No Connection

H2/10 Lt. Blue/Black (-) PTS Output [3] engine start stop switch, black 14 pin plug, pin 7 - blue Remote Start

Only

H2/11 Brown/Red (+) Siren Output [2] Security Only

H2/12 Pink No Connection No Connection

H2/13 Violet No Connection No Connection

H2/14 Brown No Connection No Connection

H2/15 White/Blue No Connection No Connection

H2/16 Red/Blue No Connection No Connection

10 933.TL2 4.12.193.2 2015 Toyota Sienna (Smart Key)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Connection

H2/17 Black/White No Connection No Connection

H2/18 Orange/Black No Connection No Connection

H2/19 Blue No Connection No Connection

H2/20 Green No Connection No Connection

H2/21 Gray (-) Hood Switch Input [1]

H2/22 Violet/White No Connection No Connection

Main harness, 12-pin black connector (H3)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Connection

H3/1 Blue/White Relay N.C. No Connection No Connection

H3/2 Blue/Red Relay N.O. (-) Ground (chassis ground) Remote Start

Only

H3/3 Blue Relay COM (-) SLP Output steering lock actuator on steering column, black 7 pin plug, pin

- green Remote Start

Only

H3/4 White/Brown Relay N.C. No Connection No Connection

H3/5 White Relay COM No Connection No Connection

H3/6 Red (+) 12 Volt Input OBD-Data Link Connector, white 16 pin plug, pin 16 + black (7.5A) Mandatory

H3/7 Lt. Green/Red Relay N.O. No Connection No Connection

H3/8 Lt. Green Relay COM No Connection No Connection

H3/9 Lt. Green/White Relay N.C. No Connection No Connection

H3/10 Black (-) Ground (chassis ground) Mandatory

H3/11 White Relay COM No Connection No Connection

H3/12 Red (+) 12 Volt Input OBD-Data Link Connector, white 16 pin plug, pin 16 + black (7.5A) Mandatory

Relay harness, 10-pin white connector (H4)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Connection

H4/1 N/A No Connection No Connection

H4/2 Red/Black No Connection No Connection

H4/3 Pink/Black No Connection No Connection

H4/4 Pink/White No Connection No Connection

H4/5 Red No Connection No Connection

H4/6 Green No Connection No Connection

H4/7 Violet No Connection No Connection

H4/8 Orange No Connection No Connection

H4/9 Red/White No Connection No Connection

H4/10 Pink No Connection No Connection

Autres manuels pour DS3+

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Directed Accessoires automobiles

Directed

Directed DIRECTECHS CHRYSLER3 Manuel utilisateur

Directed

Directed Directechs DB3 Manuel utilisateur

Directed

Directed Directechs NISS07 Manuel utilisateur

Directed

Directed XPRESSKIT optimax Series Manuel utilisateur

Directed

Directed Directechs HYUNDAI8 Manuel utilisateur

Directed

Directed Directechs DB3 Manuel utilisateur

Directed

Directed Xpresskit DBALL2 Manuel utilisateur

Directed

Directed Directechs DB3 Manuel utilisateur

Directed

Directed 403.SUBARU11 Manuel utilisateur

Directed

Directed MIT4 Manuel d'utilisation et d'entretien

Directed

Directed Directechs DB3 Manuel utilisateur

Directed

Directed DS4+ Manuel utilisateur

Directed

Directed Directechs DB3 Manuel utilisateur

Directed

Directed Directechs DB3 Manuel utilisateur

Directed

Directed Xpresskit DBALL2 Manuel utilisateur

Directed

Directed DS4+ Manuel utilisateur

Directed

Directed DS3+ Manuel utilisateur

Directed

Directed Directechs DB3 Manuel utilisateur

Directed

Directed Directechs DB3 Manuel utilisateur

Directed

Directed Directechs DB3 Manuel utilisateur

Directed

Directed DS3+ Manuel utilisateur

Directed

Directed Directechs DB3 Manuel utilisateur

Directed

Directed 933.NISS3HT Manuel utilisateur

Directed

Directed Install Essentials CAN1 Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur