Directed Directechs DB3 Manuel utilisateur
Designed by Installers for Installers
INSTALLATION GUIDE
DB3
2011 Mitsubishi Lancer Evolution. 403.MIT3 2.11
© 2021 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.
Introduction 3
Vehicle function compatibilities 3
Pre-installation and application warnings 4
Wiring diagram 4
Locating components in the vehicle 6
Vehicle connections 7
Connecting the module 9
Module programming 10
LED diagnostics and troubleshooting 11
Soft reset 13
Hard reset 13
Feature programming 14
Feature and option list 15
Limited one year consumer warranty 15
Quick reference guide 16
Contents
3403.MIT3 2.11 2011 Mitsubishi Lancer Evolution
©2021 VOXX•DEI LLC. All rights reserved.
Introduction
DB3 is an all-in-one door lock and override module.
Warning!
This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs
Mobile application for smartphones. Refer to “Connecting the module” for more information.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Trunk / Hatch Release
Immobilizer Bypass-Data No Key Req'd
RAP Shut Down (Retained ACC Power)
Remote Start Takeover
SmartStart
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Driver Door Pin
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Brake Status (foot brake)
E-Brake Status
Ignition Status
4403.MIT3 2.11 2011 Mitsubishi Lancer Evolution
©2021 VOXX•DEI LLC. All rights reserved.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in
pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible
Keys required for
programming 1Keys required for
operation 0
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic
connector.
Refer to "Vehicle connections" following the wiring diagram.
General notes: This section highlights important information for this specific firmware.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
5403.MIT3 2.11 2011 Mitsubishi Lancer Evolution
©2021 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Automatic Transmission Only
31 2
45 6
(+) Ignition: White, pin 2
(+) Starter: Orange or Lt.Blue, pin 5
(+) Accessory: Lt. Green, pin 6
Wiring diagram
16
8
9
1
1412
10 42
(+) 12V Input
(-) Lock Output
(+) Parking Lights Output
(-) Auto Headlamp Shutoff Output: Green/Black: 2
(AC) Tach Output: Violet/White: 5
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 3
HS CAN Low:
Violet or White
pin 14
HS CAN High:
Yellow/Green or
Pink, pin 6
OBDII Diagnostic
(connector side view)
MS CAN High: Orange/Green: 5
MS CAN Low: Orange/Brown: 6
D2D Port
XKD2D65
(AC) Tach Input
(-) Hood (-) Hood
(+) Starter Output
(-) Ground
(+) Accessory Output
(+) Ignition Output
21
Clutch Pedal
C-309
(black conn. at ECU)
(+) 12V:
White, pin 1
C-313
C-309
C-311
ETACS/ECU
(front view - at driver kick panel)
Ignition Connector
(white conn. left side of steering column)
12
1
83
12
2
94
11
13 1017
5
1418
6
1519
7
1620
C-311
(white conn. at ECU)
(+) Parking Lights:
Brown, pin 13
(+) Parking Lights:
Yellow, pin 10
1
7
2
8
3
9
4
10
5
11
6
12
Immobilizer Connector
(black and white conn.,
right side of steering column)
MS CAN High:
Yellow or
White/Blue, pin 11
MS CAN Low:
Lt. Green or
Black/Blue, pin 10
Connect to vehicle only
if ignition controlled
door locks is activated.
Manual Transmission Only
(+) Clutch: Black/Red, pin 2
OR
1
8
3
10 12
2
9
4
11 13
5
14
6
15
7
16
(-) Driver Door Trigger:
Yellow, pin 16
C-313
(brown conn. at ECU)
6 Amp
diodes
7403.MIT3 2.11 2011 Mitsubishi Lancer Evolution
©2021 VOXX•DEI LLC. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2011 Mitsubishi Lancer Evolution. Refer to “Pre-installation and application warnings” for a list of important notes.
Data 14-pin blue connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H1/1 Light Green No Connection No Connection
H1/2 Violet/Yellow No Connection No Connection
H1/3 Tan/Black (DATA) HS CAN High data link connector, black 16 pin plug, pin 6 data pink
H1/4 Tan (DATA) HS CAN Low data link connector, black 16 pin plug, pin 14 data white
H1/5 Orange/Green (DATA) MS CAN High Wireless Control Module on key switch, white 12 pin plug, pin 11 data white/blue
H1/6 Orange/Brown (DATA) MS CAN Low Wireless Control Module on key switch, white 12 pin plug, pin 10 data black/blue
H1/7 Brown Relay N.O. No Connection No Connection
H1/8 Yellow Relay COM No Connection No Connection
H1/9 Orange/Yellow Relay N.C. No Connection No Connection
H1/10 Orange/Red Relay N.C. No Connection No Connection
H1/11 Yellow/Red Relay COM No Connection No Connection
H1/12 Brown/Red Relay N.O. No Connection No Connection
H1/13 Red (+) W2W Only - 12 Volt dash fuse box, black 2 pin plug, pin 1 + white (80A)
H1/14 Black (-) W2W Only - Ground (chassis ground)
Output 12-pin red connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H2/1 Black/White (-) W2W Only - E-Brake Output Remote Starter
H2/2 Green/Black (-) Auto Headlamp Shutoff Output dash fuse box, brown 16 pin plug, pin 16 - yellow
H2/3 Green/White (-) W2W Only - Door Output Remote Starter
H2/4 Red/Black (-) W2W Only - Trunk Output Remote Starter
H2/5 Violet/White (AC) W2W Only - Tach Output [1] Remote Starter
H2/6 Gray (+) W2W Only - Brake Output Remote Starter
H2/7 Gray/Black No Connection No Connection
H2/8 Violet/Green No Connection No Connection
H2/9 Violet/Brown No Connection No Connection
H2/10 Yellow/Black No Connection No Connection
H2/11 Orange/Black No Connection No Connection
H2/12 Blue/Red (-) W2W Only - Hood Output Remote Starter
Input 10-pin black connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H3/1 Green (-) W2W Only - Lock Input Remote Starter
8403.MIT3 2.11 2011 Mitsubishi Lancer Evolution
©2021 VOXX•DEI LLC. All rights reserved.
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H3/2 Blue (-) W2W Only - Unlock Input Remote Starter
H3/3 Red/White (-) W2W Only - Trunk Output [2] Remote Starter
H3/4 White/Violet No Connection No Connection
H3/5 Violet/Black No Connection [3] No Connection
H3/6 White/Black No Connection No Connection
H3/7 Pink/White No Connection No Connection
H3/8 Violet No Connection No Connection
H3/9 Pink No Connection No Connection
H3/10 Blue/White (-) W2W Only - Ground When Running (Status) Input Remote Starter
D2D 4-pin white connector (H4)
Module
Conn./Pin Color Description
H4/1 Blue (Data) TX
H4/2 Black (-) Ground
H4/3 Green (Data) RX
H4/4 Red (+) 12 Volt
RF 2-pin white connector (H5)
Module
Conn./Pin Color Description
H5/1 N/A
H5/2 N/A
Additional remote start connections
(Not all of these connections may be required for your installation. Refer to the wiring diagram for vehicle-specific connections.)
Wire Connects To
Wire Location (+/-) Wire Color
12 Volts dash fuse box, black 2 pin plug, pin 1 + white (80A)
Accessory ignition switch, white 6 pin plug, pin 6 + lt. green
Clutch Pedal clutch switch, white 2 pin plug, pin 2 + black/red
Ground (chassis ground)
Ignition ignition switch, white 6 pin plug, pin 2 + white
Parking Lights - Must use a diode dash fuse box, white 20 pin plug, pin 10, 13 + yellow (L); gray (R)
Power Lock driver kick, brown 24 pin plug, pin 2 - yellow/red
Starter ignition switch, white 6 pin plug, pin 5 + orange
Tachometer any fuel injector ac NOT red/black
9403.MIT3 2.11 2011 Mitsubishi Lancer Evolution
©2021 VOXX•DEI LLC. All rights reserved.
Connecting the module
Important!
Make all the required connections to the vehicle, as described in this guide, and double check to ensure everything is correct prior
to moving onto programming.
Warning! To take advantage of advanced features, you must use DirectLink 4.5 (and higher) or the Directechs Mobile application.
Flashing a module using your computer:
1. Connect the interface module to your computer using the XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and select the Flash Module button.
3. Follow the instructions to select your vehicle, installation type, and configure your options.
4. Once you have configured the firmware options, click on the FLASH button.
Flashing a module using your smartphone or tablet:
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or tablet.
3. Select FLASH YOUR MODULE and follow the on screen instructions.
When the flashing operation is successful, you can proceed with the instructions below.
D2D installation
Recommended: Connect the 10-pin, 12-pin and 14-pin harnesses to the module, then
connect the 4-pin D2D harness. 3rd
(14-pin)
1st
(10-pin)
4th
(D2D)
2nd
(12-pin)
OR
W2W installation
If required: Connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin
harness to the module. 3rd
(14-pin)
1st
(10-pin)
2nd
(12-pin)
10 403.MIT3 2.11 2011 Mitsubishi Lancer Evolution
©2021 VOXX•DEI LLC. All rights reserved.
Module programming
Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes.
1
Wait until the LED turns ON solid red.
Note: To skip the transponder programming and use convenience features only, press
the programming button 5 times. Wait until the LED turns ON solid orange, then
proceed with step 2.
2Turn the ignition ON or turn the knob to the RUN position.
3
The LED will flash green and turn ON solid green for 3 seconds when programming is
completed.
Note: If the transponder programming was skipped, the LED turns ON solid orange for
3 seconds then shuts OFF when programming is done.
4Turn the ignition OFF.
You have successfully completed the module programming sequence.
Autres manuels pour Directechs DB3
82
Table des matières
Autres manuels Directed Accessoires automobiles
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed Xpresskit DBALL2 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed DIRECTECHS CHRYSLER8 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed Xpresskit DBALL2 Manuel utilisateur
Directed
Directed DS3+ Manuel utilisateur
Directed
Directed DBALL2-TL7 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed FORD6 Manuel d'utilisation et d'entretien
Directed
Directed FORD12 Manuel utilisateur
Directed
Directed GM10 Manuel d'utilisation et d'entretien
Directed
Directed Directechs VW08 Manuel utilisateur
Directed
Directed Directechs DS3 Manuel utilisateur
Directed
Directed XPRESSKIT optimax Series Manuel utilisateur
Directed
Directed DIRECTECHS HYUNDAI11 Manuel utilisateur
