Directed 403.MIT3 Manuel utilisateur
DB3 403.MIT3
v2.11
2008 Mitsubishi Lancer
Introduction 3
Vehicle function compatibilities 4
Pre-installation and application warnings 5
Wiring diagram 6
Locating components in the vehicle 7
Vehicle connections 8
Module programming 10
For Convenience-Only programming, see next section. 10
Module programming for convenience only (skip transponder) 11
Connecting the module 11
LED diagnostics and troubleshooting 13
Soft reset 15
Hard reset 15
Feature programming 16
Feature and option list 17
Limited one year consumer warranty 18
Quick Reference Guide (customer copy) 19
Contents
3403.MIT3 2.11 2008 Mitsubishi Lancer
©2023 Directed. All rights reserved.
Introduction
DB3 is an all-in-one door lock and override module.
Warning!
This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs
Mobile application for smartphones. Refer to “Connecting the module” for more information.
4403.MIT3 2.11 2008 Mitsubishi Lancer
©2023 Directed. All rights reserved.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Trunk / Hatch Release
Immobilizer Bypass-Data No Key Req'd
RAP Shut Down (Retained ACC Power)
Remote Start Takeover
SmartStart
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Driver Door Pin
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Brake Status (foot brake)
E-Brake Status
Ignition Status
5403.MIT3 2.11 2008 Mitsubishi Lancer
©2023 Directed. All rights reserved.
Pre-installation and application warnings
START HERE This section highlights important information for this specific firmware and will assist in pricing accordingly, as
well as bringing awareness to any operational or vehicle limitations.
Compatibilities and Requirements
T-Harness
compatible T-Harness is not compatible.
AUX
Keys required for
programming 1Keys required
for operation 0
Vehicle Takeover Refer to the Quick Reference Guide section for more details.
Firmware notes
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
Refer to the "Vehicle connections" following the installation diagram.
Footnotes
[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory
hood pin, or if not supported in data.
[2] Tach: The tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
6403.MIT3 2.11 2008 Mitsubishi Lancer
©2023 Directed. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Wiring diagram
C-309
(black 2-pin
conn. at ECU)
12
Automatic Transmission Only
31 2
45 6
(+) Ignition: White, pin 2
(+) Starter: Orange or Lt. Blue, pin 5
(+) Accessory: Lt. Green, pin 6
16
8
9
1
1412
10 42
(+) Parking Lights Output
(-) Lock Output
(+) 12V Input
(-) Auto Headlamp Shutoff Output: Green/Black: 2
(AC) Tach Output: Violet/White: 5
HS 1 CAN Low: Tan: 4
HS CAN 1 High: Tan/Black: 3
HS CAN 1 Low:
Violet or White
pin 14
HS CAN 1 High:
Yellow/Green or
Pink, pin 6
OBDII Diagnostic
(connector side view)
HS CAN 2 High: Orange/Green: 5
HS CAN 2 Low: Orange/Brown: 6
D2D Port
XKD2D65
(AC) Tach Input
(-) Ground
(+) Starter Output
(+) Accessory Output
(+) Ignition Input/Output
Manual Transmission Only
(+) Clutch: Black/Red, pin 2
21
Clutch Pedal
(+) 12V:
White or Black/Red, pin 1
C-313
C-309
C-311
ETACS/ECU
(front view - at driver kick panel)
Ignition Connector
(white 6-pin conn.
left side of steering column)
1
83
12
2
94
11
13 1017
5
1418
6
1519
7
1620
C-311
(white 20-pin conn. at ECU)
(+) Parking Lights:
Brown, pin 13
(+) Parking Lights:
Yellow, pin 10
OR
1
8
3
10 12
2
9
4
11 13
5
14
6
15
7
16
(-) Driver Door Trigger:
Yellow, pin 16
C-313
(brown 16-pin conn. at ECU)
6 Amp
diodes
(-) Hood Pin Input
Hood Pin
Connect to vehicle
only if ignition
controlled door
locks are activated.
1
7
2
8
3
9
4
10
5
11
6
12
Immobilizer Connector
(black and white 12-pin conn.,
right side of steering column)
HS CAN 2 High:
Yellow or White/Blue,
pin 11
HS CAN 2 Low:
Lt. Green or Black/Blue,
pin 10
8403.MIT3 2.11 2008 Mitsubishi Lancer
©2023 Directed. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2008 Mitsubishi Lancer. Refer to “Pre-installation and application warnings” for a list of important notes.
Data 14-pin blue connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H1/1 Light Green No Connection No Connection
H1/2 Violet/Yellow No Connection No Connection
H1/3 Tan/Black (DATA) HS CAN High 1 data link connector, black 16 pin plug, pin 6 data yellow/green
H1/4 Tan (DATA) HS CAN Low 1 data link connector, black 16 pin plug, pin 14 data violet
H1/5 Orange/Green (DATA) HS CAN High 2 Wireless Control Module on key switch, white 12 pin plug, pin 11 data yellow
H1/6 Orange/Brown (DATA) HS CAN Low 2 Wireless Control Module on key switch, white 12 pin plug, pin 10 data lt. green
H1/7 Brown Relay N.O. - No Connection No Connection
H1/8 Yellow Relay COM. - No Connection No Connection
H1/9 Orange/Yellow Relay N.C. - No Connection No Connection
H1/10 Orange/Red Relay N.C. - No Connection No Connection
H1/11 Yellow/Red Relay COM. - No Connection No Connection
H1/12 Brown/Red Relay N.O. - No Connection No Connection
H1/13 Red (+) W2W Only - 12 Volt dash fuse box, black 2 pin plug, pin 1 + white (80A)
H1/14 Black (-) W2W Only - Ground (chassis ground)
Output 12-pin red connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H2/1 Black/White (-) W2W Only - E-Brake Output Remote Starter
H2/2 Green/Black (-) Auto Headlamp Shutoff Output dash fuse box, brown 16 pin plug, pin 16 - yellow
H2/3 Green/White (-) W2W Only - Door Output Remote Starter
H2/4 Red/Black (-) W2W Only - Trunk Output Remote Starter
H2/5 Violet/White (AC) W2W Only - Tach Output [2] Remote Starter
The tach wire is an optional connection required on some remote starters,
which do not support a tach signal in D2D.
H2/6 Gray (+) W2W Only - Brake Output Remote Starter
H2/7 Gray/Black No Connection No Connection
H2/8 Violet/Green No Connection No Connection
H2/9 Violet/Brown No Connection No Connection
H2/10 Yellow/Black No Connection No Connection
H2/11 Orange/Black No Connection No Connection
H2/12 Blue/Red (-) W2W Only - Hood Output Remote Starter
9403.MIT3 2.11 2008 Mitsubishi Lancer
©2023 Directed. All rights reserved.
Input 10-pin black connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color
H3/1 Green (-) W2W Only - Lock Input Remote Starter
H3/2 Blue (-) W2W Only - Unlock Input Remote Starter
H3/3 Red/White (-) W2W Only - Trunk Output Remote Starter
H3/4 White/Violet No Connection No Connection
H3/5 Violet/Black No Connection No Connection
H3/6 White/Black No Connection No Connection
H3/7 Pink/White No Connection No Connection
H3/8 Violet No Connection No Connection
H3/9 Pink No Connection No Connection
H3/10 Blue/White (-) W2W Only - Ground When Running (Status) Input Remote Starter
D2D 4-pin white connector (H4)
Module
Conn./Pin Color Description
H4/1 Blue (Data) TX
H4/2 Black (-) Ground
H4/3 Green (Data) RX
H4/4 Red (+) 12 Volt
RF 2-pin white connector (H5)
Module
Conn./Pin Color Description
H5/1 N/A
H5/2 N/A
Additional remote start connections
(Not all of these connections may be required for your installation. Refer to the wiring diagram for vehicle-specific connections.)
Wire Connects To
Wire Location (+/-) Wire Color
12 Volts dash fuse box, black 2 pin plug, pin 1 + white (80A)
Accessory ignition switch, white 6 pin plug, pin 6 + lt. green
Clutch Pedal clutch switch, white 2 pin plug, pin 2 + black/red
Ground (chassis ground)
Hood Pin [1] dash fuse box, bottom edge, white 16 pin plug, pin 12 - red/white (some models only)
Ignition ignition switch, white 6 pin plug, pin 2 + white
Parking Lights - Must use a diode dash fuse box, white 20 pin plug, pin 10, 13 + yellow (L); brown (R)
Power Lock driver kick, brown 24 pin plug, pin 2 - yellow/red
Starter ignition switch, white 6 pin plug, pin 5 + orange
Tachometer [2] any fuel injector ac NOT red/white (non-turbo) or red/black (turbo)
10 403.MIT3 2.11 2008 Mitsubishi Lancer
©2023 Directed. All rights reserved.
Module programming
Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes.
For
Convenience-Only
programming, see next section.
1Ensure vehicle is in a safe location and cannot move forward during programming. For
vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral
position
2
The harnesses must be connected in this exact order:
Connect the 14-pin.1.
Connect the 12-pin.2.
Connect the 10-pin.3.
When the LED turns on solid red, proceed with the next step.
3Turn the ignition ON or turn the knob to the RUN position.
4The LED will flash green and turn ON solid green for 3 seconds when programming is
completed.
5Turn the ignition OFF.
You have successfully completed the module programming sequence.
Table des matières
Autres manuels Directed Accessoires automobiles
Directed
Directed DS4+ Manuel utilisateur
Directed
Directed DS4+ Manuel utilisateur
Directed
Directed DS3+ Manuel utilisateur
Directed
Directed Directechs HYUNDAI1 Manuel utilisateur
Directed
Directed Directechs NISS07 Manuel utilisateur
Directed
Directed VOXX DEI 403.VW14 v2.11 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed DIRECTECHS CHRYSLER8 Manuel utilisateur
Directed
Directed FORD5 Manuel utilisateur
Directed
Directed Directechs HYUNDAI8 Manuel utilisateur
Directed
Directed 933.SUBARU2 Manuel utilisateur
Directed
Directed XPRESSKIT optimax Series Manuel utilisateur
Directed
Directed DIRECTWIRE DIRECTECHS THGMN4 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed Directechs DB3 Manuel utilisateur
Directed
Directed DS4+ Manuel utilisateur
Directed
Directed Directechs VW08 Manuel utilisateur
