Dimplex OS2527GB Manuel utilisateur

Owner’s Manual

Model

OS2527GB

6909560100

7213880100R00

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use the stove. For your safety, always

comply with all warnings and safety instructions contained in this

manual to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this unit.

!NOTE: Procedures and

techniques that are considered

important enough to

emphasize.

CAUTION: Procedures and

techniques which, if not

carefully followed, will result in

damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations ....................3

IMPORTANT INSTRUCTIONS ..................4

Installation..................................6

Assembly...................................7

Operation...................................9

Maintenance...............................12

Warranty .................................14

Replacement Parts ..........................16

Model Number

Serial Number

Welcome & Congratulations

Thank you and congratulations for purchasing an Optimyst®stove from

Dimplex. Please use our convenient online registration page to record

your model and serial numbers for future reference at

www.dimplex.com/register

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

In order to better serve you, please have your model and serial number

ready or register your product online before calling (See above)

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in

a possible electric shock, re hazard and will void the warranty.

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

①Read all instructions before

using the unit.

②

The heater is hot when in use.

To avoid burns, do not let bare skin

touch hot surfaces. The trim around

the heater outlet becomes hot

during heater operation.

DANGER:

High temperatures

may be generated under certain

abnormal conditions. Do not

partially of fully cover the front of

this heater.

③

Extreme caution is necessary

when any heater is used by or near

children or invalids and whenever

the unit is left operating and

unattended.

④ Always unplug the unit when

not in use.

⑤ Do not operate any unit with

a damaged cord or plug, or if

the unit has been dropped or

damaged in any manner. Contact

Dimplex Technical Service at

1-888-346-7539.

⑥ Do not use outdoors.

⑦ The unit is not intended for use

in bathrooms, laundry areas and

IMPORTANT INSTRUCTIONS

similar indoor locations. Never

locate unit where it may fall into a

bathtub or other water container.

⑧ Do not run the cord under

carpeting. Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from trafc

area and where it will not be

tripped over.

⑨ To disconnect the unit, turn the

controls off, then remove the plug

from the outlet.

⑩ Always use properly grounded,

fused and polarized outlets.

⑪

Do not insert or allow foreign

objects to enter any ventilation or

exhaust opening as this may cause

an electric shock or re, or damage

to the heater.

⑫

To prevent a possible re, do

not block air intake or exhaust

in any manner. Do not use on

soft surfaces, like a bed, where

openings may become blocked.

⑬

All electrical heaters have hot

and arching or sparking parts inside.

Do not use in areas where gasoline,

paint, or ammable liquids are used

or stored or where the unit will be

exposed to ammable vapors.

⑭ Do not modify the unit. Use it

only as described in this manual.

Any other use not recommended

SAVE THESE INSTRUCTIONS

by the manufacturer may cause

re, electric shock or injury to

persons.

⑮

To reduce the risk of electric

shock, this appliance must be

grounded. Avoid the use of an

extension cord. Extension cords

may overheat and cause a risk of

re. Always plug heaters directly

into a wall outlet/receptacle. Never

use with an extension cord or

relocatable power tap (outlet/power

strip).

⑯ Do not burn wood or other

materials in the unit.

⑰ Always use a certied

electrician should new circuits or

outlets be required.

⑱ Disconnect the power supply

before performing any cleaning,

maintenance or relocation of the

unit.

⑲

When transporting or storing

the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

⑳ The stove must not be located

directly below a socket outlet.

㉑ The stove must be positioned

so that the plug is accessible.

WARNING: Remote control

contains small batteries.

Keep away from children. If

swallowed, seek medical attention

immediately.

WARNING: Do not install

battery backwards, charge, put

in re or mix with used or other

battery types - may explode or

leak causing injury.

!NOTE: Changes or

modications not expressly

approved by the party responsible

for compliance could void

user's authority to operate the

equipment.

IMPORTANT INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

6 www.dimplex.com

Installation

WARNING: Ensure the power

cord is not installed so that it is

pinched or against a sharp edge

and ensure that the power cord is

stored or secured to avoid tripping

or snagging to reduce the risk

of re, electric shock or injury to

persons.

WARNING: Construction

and electrical outlet wiring must

comply with local building codes

and other applicable regulations

to reduce the risk of re, electric

shock and injury to persons.

WARNING: Do not attempt

to wire your own new outlets or

circuits. To reduce the risk of re,

electric shock or injury to persons,

always use a licensed electrician.

WARNING: To reduce the risk

of re, do not store or use gaso-

line or other ammable vapors or

liquids in the vicinity of the heater.

!NOTE: A 15 Amp, 120 Volt cir-

cuit is required. A dedicated circuit

is preferred but not essential in all

cases. A dedicated circuit will be

required if, after installation, the

circuit breaker trips or the fuse

blows on a regular basis when the

heater is operating. Additional ap-

pliances on the same circuit may

exceed the current rating of the

circuit breaker.

CAUTION: A minimum of

24.6in. (625mm) from a corner, is

recommended for optimum airow

and ame production.

Wiring

LINE IN

MOTOR

ELEMENT

THERMAL

CUTOUT

PCB

ELEMENT

THERMOSTAT

TRANSFORMER

LIGHTSLIGHTS

POWER

BOARD

SELECTOR

SWITCH

POTENTOMETER

IR SENSOR

TRANSDUCER

FAN MOTOR

NEUTRAL

GROUND

Logset

Removable

Rell

Container

Light

Bulbs

Assembly

Figure 1

1. Carefully unpack all of the

components from the box.

(Figure 1)

2. Remove top cover by turning

the retaining tabs on both

ends of the water reservoir.

(Figure 2)

3. Install the light bulbs by

aligning the pins on the bulbs

and the xture and pressing

down until they are fully

inserted. (Figure 2)

4. Install the transducer so that

it is sitting level in the circular

holding area in the reservoir.

Figure 2

Top

Cover

Transducer Emitter

Wire Slot

Remote

Control

5. Orient transducer wire so that

it does not sit directly above

the emitter and the wire

passes through the slot in the

side of the tank. (Figure 2)

6. Reinstall the top cover and

ensure both retaining tabs

have been turned so that they

are pointing inwards.

7. Fill and install the Rell

Container.

!NOTE: Normal tap water can

be used in the Optimyst®as long

as the tap water is not considered

to be hard water. In the event

your tap water is hard, you may

8 www.dimplex.com

Assembly

Figure 3

use softened water or distilled

water with 1/8 tsp of salt (0.5

mL) added to the water reservoir.

(The addition of additional salt

should only be used when you

notice that the unit is not produc-

ing mist as expected.)

!NOTE: During initial

installation, the Rell Container

should be relled after the

Reservoir has lled to ensure the

maximum operating time.

8. Install the logset on top,

so that the opening is not

blocked.

9. Make sure the On/Off switch

is switched to Off (refer to

Operating Instruction section).

10. Plug the unit into a 15 Amp/

120 volt outlet.

Operation

!NOTE: When the unit is used

in an environment where back-

ground noise is very low, it may

be possible to hear a sound which

is related to the operation of the

ame effect. This is normal and

should not be a cause for con-

cern.

!NOTE: Always ensure that

the appliance is in a level posi-

tion.

The manual controls for the unit

are located below the control

cover infront of the log grate

(Figure 4).

A. On/Off Switch

Supplies power to the unit.

B. Thermostat Control

To adjust the temperature to your

individual requirements, turn

the thermostat control clock-

wise all the way to turn on the

heater. When the room reaches

the desired temperature, turn

the thermostat knob counter-

clockwise until you hear a click.

Leave thermostat in this position

to maintain the room temperature

at this setting. For additional heat,

turn clockwise until you hear the

click again and the heater will turn

on.

C. Mode Selector Switch

Press once to turn on the

ame effect. This will be indicated

by an audible “beep”. Although

the lights turn on immediately it

will take 30 seconds before the

ame effect starts.

• Press again to give ame ef-

fect and full heat. This will be

indicated by two “beeps”.

• Press again to return to ame

effect only. This will be indi-

cated by one “beep”.

• Press to put re in to

standby mode. This will be

indicated by one “beep”.

D. Flame Intensity Control

Adjusts the intensity of the ame

and smoke effect when the heater

Figure 4

10 www.dimplex.com

has been activated.

Turning the control knob clock-

wise decreases the intensity of

the ame and smoke effect. Turn-

ing the control counterclockwise

will increase the ame and smoke

effect.

!NOTE: Give the ame genera-

tor some time to react to changes

you may make on the ame

control knob.

!NOTE: When the water tank is

empty the unit will turn off after 30

seconds. See instructions under

Maintenance Section for rell-

ing tank. When this procedure is

complete, the main lamps will illu-

minate but it will take 30 seconds

before the ames return.

Resetting the Temperature

Cutoff Switch

Should the heater overheat, an

automatic cut out will turn the

replace off and it will not come

back on without being reset. It

can be reset by switching the On/

Off Switch to Off and waiting 10

minutes before switching the unit

back on.

CAUTION: If you need to con-

tinuously reset the heater, unplug

the unit and call Dimplex North

America Limited at 1-888-346-

7539 for technical support. Please

have your model and serial num-

ber ready when calling.

Remote Control

The On/Off Switch must be in the

‘ON’ ( I ) position in order for the

remote control to operate (Figure

3A). There are 3 buttons on the

remote control. (Figure 5)

!NOTE: To operate cor-

rectly the remote control must

be pointed towards the remote

control sensor.

The remote control functions are

as follows:

Press once to turn on Flame

effect only. This will be indi-

cated by one beep.

Press once to turn on Full

heat and Flame effect. This

will be indicated by two

beeps.

Standby - This will be indi-

cated by one beep.

!NOTE: Once the mist has

been activated, the unit will have

to be turned Off, using either the

momentary button, on the unit,

or the Off button on the remote

control, then back on to return

Operation

Autres manuels pour OS2527GB

Table des matières

Autres manuels Dimplex Cheminée intérieure

Dimplex

Dimplex DWF3651 Manuel utilisateur

Dimplex

Dimplex GDS23L8-1904GB Manuel utilisateur

Dimplex

Dimplex BF 30' series Manuel d'utilisation

Dimplex

Dimplex VCX1525 Manuel utilisateur

Dimplex

Dimplex BLF50 Manuel utilisateur

Dimplex

Dimplex DWF120330B Manuel utilisateur

Dimplex

Dimplex OptiFlame Cheriton Deluxe Mode d’emploi

Dimplex

Dimplex EWM-COPPER Manuel utilisateur

Dimplex

Dimplex CLEMENT CMT20BL Manuel utilisateur

Dimplex

Dimplex DF2600 Manuel utilisateur

Dimplex

Dimplex BELLINI CONCRETE BLN15C Manuel utilisateur

Dimplex

Dimplex DFI400L Manuel utilisateur

Dimplex

Dimplex IN-STUD V1525BT Manuel utilisateur

Dimplex

Dimplex BINGHAM BHM 10 Manuel utilisateur

Dimplex

Dimplex MULTIFIRE DF3015 Manuel utilisateur

Dimplex

Dimplex Osbourne Manuel utilisateur

Dimplex

Dimplex DWF-1326 Manuel utilisateur

Dimplex

Dimplex EWMC-CC-SS Manuel utilisateur

Dimplex

Dimplex CFP49449BW Manuel utilisateur

Dimplex

Dimplex BFSL33 Manuel utilisateur

Dimplex

Dimplex SF3202 Manuel utilisateur

Dimplex

Dimplex SIL48 Manuel utilisateur

Dimplex

Dimplex Navara Nav15 Log Manuel utilisateur

Dimplex

Dimplex Anthony Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation