Dimplex QXD1500E Manuel utilisateur
08/54003/0 ISSUE: 1
Quartzray Infrared Heater
Models: QXD1500E / QXD3000E / QXD4500E
INSTRUCTION MANUAL
Installation and Operating
This product is supplied and operated with a Bluetooth Remote Control handset
IMPORTANT
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR
FUTURE REFERENCE. Note also the information presented on the appliance
IMPORTANT SAFETY ADVICE
• Because the Dimplex Quartz Radiant Heater contains no moving parts little
maintenance is required. Before undertaking any maintenance work on the
heater due attention must be paid to the following:
• The installation of these appliances must always be carried out by a
competent electrician and be in accordance with the current wiring
regulations and relevant Building Regulations.
• The radiated heat from the heater is considerable and must be taken into
account when locating the heater. Ensure that the heater is not used in close
proximity to the skin or eyes.
• Always isolate the heater from the supply before undertaking any
maintenance work on the appliance.
• This heater is designed to be horizontally wall mounted only, it must not be
ceiling mounted.
• Always ensure a safe mounting height, at or above a minimum height of 1.8
metres from ground level, so that the heater can not be touched when in
operation.
• The heater must be wall mounted level ± 5º to the horizontal.
• Do not locate the heater immediately above or below a fixed socket outlet or
connection box.
• This heater must not be located immediately above or below a fixed socket
outlet or connection box.
• The heater must be installed in a location that is free from vibration.
• The QXD range of heaters are designed for internal use only. They are not
rated as flame-proof and must not be used when flammable dusts, gases, or
vapours, etc. are likely to be present in the atmosphere. If in doubt, advice
should be sought from the Health and Safety Executive inspectors or local fire
ocers.
• Quartz lamps are extremely fragile and must be handled with extreme care
at all times. Avoid touching the surface of the quartz sleeve with bare fingers.
If the sleeve is accidentally touched remove the finger print with a soft cloth
moistened with methylated spirits.
• The life expectancy of the halogen lamps in normal operating conditions is
over 3000 hours.
WARNING
1. This appliance must be earthed.
2. Means for disconnection from the electrical supply must be incorporated in
the fixed wiring in accordance with the wiring regulations.
3. Do not use this heater in the immediate surroundings of a bath, a shower or a
swimming pool.
4. This appliance can be used by children aged from 8 years and above and
2
persons with reduced physical, sensory or mental capabilities or lack of
experience or knowledge if they have been given supervision or instruction
concerning the use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
5. Children of less than 3 years should be kept away unless continuously
supervised.Children aged from 3 years and less than 8 years shall only switch
on/o the appliance provided that it has been placed or installed in its
intended normal operating position and they have been given supervision or
instruction concerning the use of the appliance in a safe way and understand
the hazards involved. Children aged from 3 years and less than 8 years shall
not plug in, regulate and clean the appliance or perform user maintenance.
6. The supply circuit to the heater must incorporate a double pole isolating
switch having a constant separation of at least 3mm in all poles.
CAUTION
• Some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present.
• Always disconnect the heater from the electricity supply and leave to cool for a
minimum of 30 minutes before attempting to work on or near it.
• Always ensure a safe means of access using an access tower or properly
supported ladder.
• Do not cover the heater.
• Do not position any combustible or heat sensitive materials too close to the
heater.
• Do not use heater if the elements are broken - as injury may occur.
• Allow adequate time (minimum of 30 mins.) for the elements and body casing
to cool before attempting to work on the heater.
• Wiring between the heater and the spur outlet or isolation switch must be in a
heat resisting cable (e.g. polychloroprene).
Provide sucient slack to the cable to allow for angular adjustment of the body.
WARNING: KEEP BATTERIES OUT OF REACH OF CHILDREN
• Swallowing may lead to serious injury in as little as 2 hours or death, due to
chemical burns and potential perforation of the oesophagus.
• If you suspect your child has swallowed or inserted a battery go straight to a
hospital emergency room.
• Examine devices and make sure the battery compartment is correctly
secured, i.e. that the battery cover is fitted securely. Do not use if the
compartment is not secure.
• Dispose of used batteries immediately and safely. Flat batteries can still be
dangerous.
3
Cable Installation (see Fig 1 & 2)
Remove the two screws which hold the plastic terminal cover box (A) in place, lift o
the terminal cover box and set aside with the two screws for future use.
Remove the two screws securing the cable saddle clamp (B) and also set them safely
aside for future use.
Set the end of the power supply cable into position on the clamp (C) and strip a suitable
length of cable sheath o the end of the power supply cable so that Live, Neutral and
Earth wires are a suitable length to fit between the clamp (C) and the screw fixing
locations in the termial block provided (D) as shown.
Strip the ends of the Live, Neutral and Earth wires and fit each end under the protector
plates of the terminal block. Ensure the terminal screws are tight and the wires are
clamped securely by the terminal screws.
Place the end of the power supply cable sheath onto the the clamp (C). Refit and tighten
the cable saddle clamp (B) securely on top using the two screws previously removed.
Refit the terminal cover box (A) to the base moulding using the two screws previously
removed.
Ensure the power supply cable when fitted does not make contact with the body of
the heater.
Commissioning
•
Checks on the electrical installation should include earth continuity and insulation tests
and must be undertaken by a competent person.
• Ensure that all the electrical connections at the lamps and the terminal rails have been
made correctly, that they are tight and that there is no loose or frayed wire.
• Replace and secure the terminal cover box and replace and secure the front panel.
• Check that the mounting bracket is securely fixed in the vertical position such that the
lamps remain in a horizontal plane at all angles of heater displacement.
• Roughly align the heater(s) and tighten the adjusters.
•
Switch on the heater(s) and check that the lamp(s) are all operating. If time or temperature
controls are fitted check these for correct and safe operation by reference to the
supplier’s instructions.
•
Make any adjustments that are necessary to give an even spread of heat over the
required area. This may be done simply by perception of the heating eect or by using
the distribution of visible light either at night or by darkening the room.
Hand over
Hand over these instructions and make sure the user is familiar with all aspects of operation
and safety including the need for regular cleaning and an annual inspection. In the event
of the premises being unoccupied then leave heater(s) switched o and isolated from
the electrical supply. Leave instructions adjacent to the electricity meter.
4
Fig. 1
DO NOT
REMOVE
THIS
SCREW
REMOVE SCREWS
TERMINAL
COVER BOX
MUST SLIDE
OUT FIRST
THEN UP
Fig. 2
TRIM POWER SUPPLY CABLE SHEATH SO
THAT LIVE, NEUTRAL AND EARTH WIRES ARE
AT A SUITABLE LENGTH. TIGHTEN CABLE
SADDLE CLAMP ONTO END OF POWER
SUPPLY CABLE SHEATH
A
C
D
B
5
Maintenance
Since the Dimplex Quartz Heater contains no moving parts little maintenance is required
beyond cleaning and lamp replacement. It is however, essential that the heater is not
operated with accumulation of dust or dirt on the lamp(s) or reflector(s) as this can
cause a build up of heat and eventual damage. For this reason the heater must be
inspected regularly depending upon conditions and at least at yearly intervals.
Before undertaking any maintenance work on the heater due attention must be paid
to the following:
1. Always disconnect the heater from the electricity supply before attempting to work
on or near it.
Lamp Replacement
WARNING: Before undertaking this task ensure the heater is disconnected from the
electricity supply and left to cool for a minimum of 30minutes.
1. Detach heater from its mounting position.
2. Unscrew the rear panel by loosening the corner fixing screws, and then lift rear panel
clear.
3. Disconnect the wires to the old lamp by removing the lock nuts retaining the terminal
ends adjacent to the lamp clips. Do not slacken the screws as this could disturb the
internal wiring.
4. Remove the lamp by gently releasing the ends from the spring clips. Keep the lamp
secure and do not twist the ends or apply undue force. IMPORTANT - Release and
retain the high temperature cable ties from the element wires. (These must not be
substituted).
5. Before removing the new lamp(s) from its protective packing it is important to be
aware that quartz lamps are fragile and must be handled with care at all times. Avoid
touching the surface of the quartz sleeve with bare fingers. If the sleeve is accidentally
touched remove the finger print with a soft cloth moistened with methylated spirit.
6. Hold the lamp firmly but gently at each end and oer up to the spring mounting
clips. The wire leads should face towards the front of the heater. Push the lamp fully
into the clips taking care to keep it square. Do not twist the ends or apply undue
force. If either end of the lamp will not easily engage in the spring clips remove the
lamp and gently ease the spring.
7. The wire from each end of the lamp must be connected to the threaded connector
ON THE SAME CLIP AS THE LAMP END. With the outside not loosened, insert the
spade between the two outside nuts and tighten firmly.
8. When the lamp has been fitted check that the electrical connections have been
correctly made. Re-use the same cable tie to tether the element wires in place. Re-
fit the raer panel, checking that wires are not trapped.
6
2. Always ensure a safe means of access using an access tower or properly supported
ladder.
3. Some types of quartz lamps run with an internal pressure in excess of atmospheric
pressure and while construction is very strong there is a slight risk of shattering. If
it is necessary to examine a bare lamp whilst in operation then a protective screen
must be used.
4. Allow at least 30 minutes for the lamps and body casing to cool before attempting
to work on the heater.
7
Model Identifier(s): QXD1500E QXD3000E QXD4500E
Nominal heat output Pnom 1.5 kW 3.0 kW 4.5 kW
No. of Elements 1 2 3
Height (mm) 256 380 506
Width (mm) 440 440 440
Depth (mm) 70 70 70
Minimum heat
output (indicative) Pmin N.A. 1.5kW 1.5kW
Maximum continuous heat output Pmax,c 1.5kW 3.0kW 4.5kW
Auxiliary electricity Consumption
At nominal heat output elmax 0.00 0.00 0.00
At minimum heat output elmin 0.00 0.00 0.00
In standby mode elSB <0.0005 <0.0005 <0.0005
Type of heat output/ room temperature control
Electronic room temperature control plus week timer Yes
With open window detection Yes
With adaptive start control No
This product complies with Lot20 of the Energy Eciency Directive (2015/1188).
Energy Related Product Directive
Technical Details
8
All Models
Controls
Digitally controlled, Electronic Thermostat
Timer modes:
7 Day Programmable User Timer
Continuous heat modes:
Frost Protect, Runback, Comfort O
Controller UI
O-board control only.
Controller Functions
• Open window detection
• Advance time period
• Heat Selection (High/Low) for 3/4.5kW models only
• Bluetooth for control
Construction Durable epoxy-polyester powder coated steel casing with chrome plated
grille. FR Nylon control enclosure.
Finish / Colour
Powder coated steel, finished in Matte Black
Element Ruby halogen element
Installation Supplied with wall mounting bracket
Safety No cut-out on-board. Protection via RCD
IP Rating No Rating
Battery Backup
None. However all programmed timer profiles will be retained during
short term power losses. In order to ensure their correct operation, it is
necessary to restore the time and date settings, this happens automatically
once paired with the remote.
Supply
~230-240 V, 50Hz Class I, with earth wire
Approvals CE, BEAB
Warranty 2 years
Country of Origin British Isles
Manufacturer Glen Dimplex Heating & Ventilation (GDC Group Ltd.)
9
General Information
The Dimplex QXDE range is available in 1, 2 and 3 lamp models with outputs of 1.5kW,
3.0kW and 4.5kW respectively. The three lamp models are supplied as dual voltage
units and are suitable for use on 230-240V and 415V 3N supplies.
Model No. No. of Lamps Rating
(kW)
Voltage
(V)
Weight
(kg)
QXD1500E 1 1.5 230-240 3.7
QXD3000E 2 3.0 230-240 4.3
QXD4500E 3 4.5 230-240 5.8
Material and Finished
Body Casing – Low carbon steel, powder coated.
Reflectors – 1080 (SIA) 99.8% Alum. Electrochemically brightened specular finish.
Control Housing - Flame retardant black Nylon moulding.
10
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Dimplex Chauffage
Dimplex
Dimplex DUO300i Manuel utilisateur
Dimplex
Dimplex Calidou CAL075 Manuel utilisateur
Dimplex
Dimplex DEUF2N Manuel utilisateur
Dimplex
Dimplex FX 20E IPX4 Manuel utilisateur
Dimplex
Dimplex CKHA Series Guide de configuration
Dimplex
Dimplex Studio G DXSTG25 Manuel utilisateur
Dimplex
Dimplex EWA-C 3kW Series Manuel utilisateur
Dimplex
Dimplex CXLS12N Manuel utilisateur
Dimplex
Dimplex RCE 050 Manuel utilisateur
Dimplex
Dimplex Saletto LPP050E Manuel utilisateur
Dimplex
Dimplex DuoHeat Duo300N Manuel utilisateur
Dimplex
Dimplex LPC Series Manuel utilisateur
Dimplex
Dimplex BLF3451 Manuel utilisateur
Dimplex
Dimplex Cold Watcher Manuel utilisateur
Dimplex
Dimplex VFMQ 30 Manuel utilisateur
Dimplex
Dimplex DuoHeat Duo300N Manuel utilisateur
Dimplex
Dimplex DF-X Manuel utilisateur
Dimplex
Dimplex CXLN Manuel utilisateur
Dimplex
Dimplex DTX Series Manuel d'instructions d'installation
Dimplex
Dimplex B075E Manuel utilisateur
Manuels Chauffage populaires d'autres marques
oventrop
oventrop Regucor Series Manuel utilisateur
Blaze King
Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur
ELMEKO
ELMEKO ML 150 Manuel utilisateur
BN Thermic
BN Thermic 830T Manuel utilisateur
KING
KING K Series Mode d’emploi
Empire Comfort Systems
Empire Comfort Systems RH-50-5 Guide de démarrage rapide
Empire Heating Systems
Empire Heating Systems WCC65 Manuel utilisateur
Wetekom
Wetekom 92 86 43 Manuel utilisateur
Desa
Desa SPC170-F Manuel utilisateur
Watlow
Watlow Watrod Electric Tubular Heaters Manuel utilisateur
Haverland
Haverland ECO-DRY GPS Series Manuel de la liste des pièces
Stelpro
Stelpro ASILVC2060 Series Manuel utilisateur