Dimplex DHCER20FE Manuel utilisateur

– 1 –

FLAME EFFECT

CERAMIC HEATER

INSTRUCTION MANUAL

DHCER20FE

Please read the instructions carefully before use.

Keep manual for future reference.

This product is only suitable for well insulated spaces or occasional use.

14064_DHCER20FE Manual_V2.indd 1 7/12/17 4:25 PM

– 2 –

CONTENTS

Safety Warning and Notices 2

Product Features 4

Components Description 4

Product Operation Introduction 6

Maintenance and Cleaning 8

Technical Parameters 9

Warranty 9

SAFETY WARNING AND NOTICES

Please pay close attention to the warnings and instructions in this manual for correct

operation and to avoid any danger caused by incorrect use.

1. This appliance can only be used by children 8 years and above and people

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning the use of

the appliance in a safe way and understand the hazards involved. Children should

not play with the appliance.

2. CAUTION — Some parts of this product can become very hot and cause burns.

Particular attention has to be given where children and vulnerable people are

present.

3. If the supply cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualiﬁed persons in order to avoid any hazards.

4. WARNING: In order to avoid overheating, do not cover the heater.

5. The heater must not be placed immediately below a socket outlet.

6. Do not use this heater in the immediate surroundings of a bath, shower or a

swimming pool.

7. The fan heater can only be used under supervision.

8. The air inlet/outlet area must never be covered. Keep a distance of at least

1m in front and 50cm behind the fan.

9. If there is any indication of a malfunction, contact service center repairs.

Do not attempt to disassemble the product or replace faulty parts with

unauthorized components because it will damage the unit.

14064_DHCER20FE Manual_V2.indd 2 7/12/17 4:25 PM

– 3 –

10. Do not disassemble or make changes to the product unless you are authorized by

the dealer or producer.

11. Do not touch the plug with wet hands, it may lead to electric shock.

12. Do not put foreign objects into the air inlet or outlet.

13. Do not use pesticide or other ﬂammable sprays around the product.

14. Make sure the fan doesn’t blow heated air directly at small children for long periods

of time.

15. Do not pull out the power plug by pulling the power cord, it may cause damage to

the power cord and cause an electric shock.

16. Make sure the power cord is undamaged, and the plug is correctly plugged into the

wall socket.

17. If there is an abnormal smell or noise when the product is in use, turn off the

product and pull out the power cord immediately.

18. Do not operate the appliance with a damaged power cord or plug. Send the heater

to a suitably qualiﬁed or appointed service agent for inspection and repair.

19. Make sure not to fold the power cord or place heavy objects on the power cord, it

may lead to electric shock.

20. If the heater will not be used for a long period of time, disconnect the plug.

21. Use a power outlet that meets the inspection requirements where the carrying

capacity of the socket is no less than 10A/230V.

22. Ensure the power supply voltage is consistent with the speciﬁed voltage in the

machine (220-240VAC).

23. Do not use the device directly below a power outlet.

24. When using the heater, keep combustible materials or explosive objectives, away

from the heater.

25. In order to avoid overheating, do not cover the heater.

26. Never place any objects inside the device.

14064_DHCER20FE Manual_V2.indd 3 7/12/17 4:25 PM

– 4 –

PRODUCT FEATURES

1. PTC ceramic heating element, changes the power automatically according to the

variation in the ambient temperature.

2. Optional high or low power.

3. Set timer has a range between 1-24 hours.

4. Temperature setting of 15ºC to 35ºC.

5. Uses a DC fan, which increases efﬁciency and has low operational noise.

6. Tip-over safety protection, double over-heating protection (Thermistor, temperature

fuse) for safer use.

7. Convenient operation with an infrared remote control function.

8. Oscillating, swing function.

9. LED display will automatically dim after 1 minute during operation, to save energy

and power.

10. Optional Flame effect.

COMPONENTS DESCRIPTION

PRODUCT STRUCTURE

1. Front cover

2. Wind outlet

3. Flame effect display window

4. Swing holder

5. Base

6. Power cord

7. Control panel

8. Power switch

9. Remote control

Page 4

materials or explosive objectives, away

from the heater.

28.

In order to avoid overheating, do not cover the

heater.

29.

Never place any objects inside the device.

Product features

PTC ceramic heating element, changes the power automatically according to the

variation in the ambient temperature.

Optional high or low power.

Set timer has a range between 1-24 hours.

Temperature setting of 150 to 350.

Uses a DC fan, which increases efficiency and has low operational noise.

Tip-over safety protection, double over-heating protection (Thermistor, temperature

fuse) for safer use.

Convenient operation with an infrared remote control function.

Oscillating, swing function.

LED display will automatically dim after 1 minute during operation, to save

energy and power.

10.

Optional Flame effect

Components Description

Product structure

Front cover

Wind outlet

Flame effect display window

Swing holder

Base

Power cord

Control panel

Power switch

Remote control

14064_DHCER20FE Manual_V2.indd 4 7/12/17 4:25 PM

– 5 –

Page 5

Control panel

Display panel

Remote control operation panel

Page 5

Control panel

Display panel

Remote control operation panel

Page 5

Control panel

Display panel

Remote control operation panel

CONTROL PANEL

DISPLAY PANEL

REMOTE CONTROL

OPERATION PANEL

FLAME EFFECT

TURN ON/OFF

FLAME EFFECT

POWER BUTTON

SET TEMPERATURE

SET TIMER (IN NO. OF HOURS)

LOW HEAT SETTING

ACTIVATED

HIGH HEAT SETTING ACTIVATED

TURN ON/OFF ECO MODE

ECO MODE

CHANGE HEAT

SETTINGS

TIMER + (UP) BUTTON

TIMER + (DOWN) BUTTON

MODE BUTTON (HI/LOW/ECO)

TEMP + (UP) BUTTON

TEMP + (DOWN) BUTTON

OSCILLATE BUTTON

OSCILLATING

14064_DHCER20FE Manual_V2.indd 5 7/12/17 4:25 PM

– 6 –

PRODUCT OPERATION INTRODUCTION

INSTALLATION METHOD

1. Take the device out of the bubble wrap, including the following three parts; heater,

base and remote control.

2. Put the heater on a ﬂat surface upside-down (with the base facing up). Connect the

base with the heater.

3. Turn the unit right way up.

4. Press Power button which is in the back of the device, to turn on.

REMOTE CONTROL OPERATION PANEL

1. Pull out the battery cover on the back of the remote control.

2. Pay attention to the battery polarity, and insert the battery (CR2032) into the tray of

the panel.

3. Push the battery cover back into the remote control.

Page 6

bein

Product Operation introduction

Installation method

1. Take the device out of the bubble wrap, including the following three parts;

heater, base and remote control.

2. Put the heater on a flat surface upside-down (with the base facing up). Connect the

base with the heater.

3. Turn the base right way up.

4. Press Power switch which is in the back of the device to turn on.

Remote control operation panel

1. Pull out the battery cover on the back of the remote control.

2. Pay attention to the battery polarity, and insert the battery (CR2032) into the tray

of the panel.

3. Push the battery cover back into the remote control.

The function of buttons

The fan will operate whenever the heater is heating. If the heater stops working,

then the fan will stop working after 10s.

①After connecting to the power supply and switching on the power, you will hear a

beeping sound, the heater then enters Standby Mode. The power indicator ights up.

②Under standby mode, key to turn on/off the heater. When turning off the

heater, the display panel and fan will then countdown (from 10 to 0 second) before

switching off.

③The default setting after g switched on is:

Heater：low power, lights up.

Oscillation：off, lights off.

Timer：0 hrs, lights off.

Fan：turned on.

Temperature setting: the default temperature setting is 25℃.

Fireplace display：turned on, lights up.

ECO: turned off, lights off.

THE FUNCTION OF BUTTONS

The fan will operate whenever the heater is heating. If the heater stops working, then

the fan will stop working after 10s.

1. After connecting to the power supply and switching on the power, you will hear a

beeping sound, the heater then enters Standby Mode. The power indicator

lights up.

2. Under standby mode, key to turn on/off the heater. When turning off the

heater, the display panel and fan will then countdown (from 10 to 0 second) before

switching off.

3. The default setting after being switched on is:

a) Heater: low power, lights up.

b) Oscillation: off, lights off.

c) Timer: 0 hrs, lights off.

14064_DHCER20FE Manual_V2.indd 6 7/12/17 4:25 PM

– 7 –

d) Fan: turned on.

e) Temperature setting: the default temperature setting is 25ºC.

f) Fireplace display: turned on, lights up.

g) ECO: turned off, lights off.

4. In heating mode, press to shift the power between low and high power level.

a) Low power: lights up.

b) High power: lights up.

5. In heating mode, press to enter ECO mode, lights up, press it again to

quit this mode.

a) ECO mode: the default temperature setting is 22ºC. When the room

temperature is lower than 18ºC, the machine works in high power: when

the room temperature is between 18ºC and 22ºC the machine works in low

power. When the room temperature is above 22ºC the heating element will

turn off.

b) When the ECO function is operating, the button is not active.

c) When the room temperature is above 22ºC the heater and oscillation function

will also be turned off.

6. In heating mode, press to turn on/off the oscillation function, will light

up/off accordingly.

7. In heating mode, press

Page 5

Control panel

Display panel

Remote control operation panel

Page 5

Control panel

Display panel

Remote control operation panel

button to set the timer.

a) Timer: press

Page 5

Control panel

Display panel

Remote control operation panel

Page 5

Control panel

Display panel

Remote control operation panel

key, and will display, press +/-

key to set the timer (within a range of 0-24 hours), the timer will increase or

decrease by 1hr increments.

b) Entering the timer mode by pressing

Page 5

Control panel

Display panel

Remote control operation panel

Page 5

Control panel

Display panel

Remote control operation panel

does not change

the timer settings. But you can set the timer by pressing the +/- key. After no

operation for 5 seconds, the time that you have set will be saved.

c) When the timer turns to the value “0”, the device will then turn off and enter

into standby mode.

d) If the timer is set as “0”, it means that no timer is set.

8. In heating mode, press

Page 5

Control panel

Display panel

Remote control operation panel

Page 5

Control panel

Display panel

Remote control operation panel

button to set the temperature.

a) Temperature setting function: press

Page 5

Control panel

Display panel

Remote control operation panel

Page 5

Control panel

Display panel

Remote control operation panel

key, and

SETºC will display, press +/- key to set the temperature. The range of the

temperature is from 15°C to 35°C, and can increase or decrease by 1°C

increments.

b) Entering into the temperature settings by pressing

Page 5

Control panel

Display panel

Remote control operation panel

Page 5

Control panel

Display panel

Remote control operation panel

keys

does not change the temperature settings. You can set the temperature by

pressing +/- key. After no operation for 5 seconds, the temperature that you

have set will be saved.

14064_DHCER20FE Manual_V2.indd 7 7/12/17 4:25 PM

– 8 –

9. When both the time and temperature are set, the LED display will switch between

showing the set temperature and timer setting every 30 seconds. When a timer is not

set, it will only show the set temperature.

10. When the heater is turned on or in standby mode, press button to turn on/off the

ﬂame effect function, the LED will light up/off accordingly.

11. Memory function in standby mode:

When the heater is turned on (except for the ﬁrst time), under standby mode, the unit

will revert to the last used setting (except for the timer).

12. After working for 1 minute, the brightness of the LED display will reduce to 1/3 of the

normal brightness. It will resume to the normal brightness when any operation of the

device is activated.

13. If the unit falls over the tip-over switch inside the heater will disconnect the heater

automatically.

14. Remarks:

a) when the over-heat sensor is activated (temperature is above 60ºC),the LED

display will display “EE”, and the heater will turn off.

b) When the environment temperature is lower than -10ºC, the LED will display “LO”

c) When the environment temperature is higher than 40ºC, the LED will display “HI”

MAINTENANCE AND CLEANING

1. Before any cleaning or maintenance, make sure the heater is completely turned off,

and the power cord is not connected to the wall socket.

2. Use a soft cloth to wipe the dust off the heater’s surface; If the surface is very dirty, use

a moist soft cloth to wipe it with water less than 50°C mixed with a neutral detergent.

3. Do not use gasoline, thinner or any other chemicals that can damage the surface.

4. Before storing the heater, let it cool down and store it in a dry and ventilated area.

5. Warning: any other servicing should be performed by an authorized service

representative.

14064_DHCER20FE Manual_V2.indd 8 7/12/17 4:25 PM

– 9 –

TECHNICAL PARAMETERS

Model NO. DHCER20FE

Voltage 220-240V

Frequency 50 Hz

Power 2000 W

Noise level. ≤50 dB

Dimension 260mm x 260mm x 830mm

WARRANTY

This device comes with a 2 year warranty from the date of purchase. Keep your receipt

as proof of purchase date. This guarantee only applies if the item has been used as

intended, and all instructions have been followed accordingly. Please note that this

product is for domestic use only and not for commercial use. Improper use of the

product will invalidate the guarantee. Returned goods can be accepted if repackaged in

the original product box, and presented with the original receipt.

IMPORTANT

Do not dispose this product as unsorted municipal waste, use separate

collection facilities. Contact your local government for information regarding the

collection systems available. If electrical appliances are disposed of in landﬁlls

or dumps, hazardous substances can leak into the ground water, polluting the

food chain and damaging health and well-being.

14064_DHCER20FE Manual_V2.indd 9 7/12/17 4:25 PM

Phone: 09 274 8265

Fax: 09 274 8472

Email: [email protected]

Web: www.dimplex.co.nz

Glen Dimplex New Zealand Ltd

38 Harris Road, East Tamaki

Auckland, New Zealand

P.O. Box 58473, Botany

Manukau 2163, New Zealand

14064_DHCER20FE Manual_V2.indd 10 7/12/17 4:25 PM

Table des matières

Autres manuels Dimplex Chauffage

Dimplex

Dimplex XL Manuel utilisateur

Dimplex

Dimplex LPC Series Manuel utilisateur

Dimplex

Dimplex DX 422 T Manuel utilisateur

Dimplex

Dimplex DTX Series Manuel d'instructions d'installation

Dimplex

Dimplex XLE Series Manuel utilisateur

Dimplex

Dimplex PFH30E Manuel utilisateur

Dimplex

Dimplex XL6N Manuel utilisateur

Dimplex

Dimplex BRENTA BNT20 Manuel utilisateur

Dimplex

Dimplex XLS24N Manuel utilisateur

Dimplex

Dimplex QUBEFAN Q2BT Manuel utilisateur

Dimplex

Dimplex SLR 200WE Manuel utilisateur

Dimplex

Dimplex WFE 3TNB Manuel utilisateur

Dimplex

Dimplex OFRC10 Manuel utilisateur

Dimplex

Dimplex RFI-D Series Manuel utilisateur

Dimplex

Dimplex CXLS24 Manuel utilisateur

Dimplex

Dimplex ECR15 Manuel utilisateur

Dimplex

Dimplex IRX60/120E Manuel utilisateur

Dimplex

Dimplex VFMQ 30 Manuel utilisateur

Dimplex

Dimplex Girona GFP050E Manuel utilisateur

Dimplex

Dimplex OCR15TIF Manuel utilisateur

Dimplex

Dimplex RFV-800 Manuel utilisateur

Dimplex

Dimplex DHCER24SG Manuel utilisateur

Dimplex

Dimplex Studio G DXSTG25 Manuel utilisateur

Dimplex

Dimplex AC3CN Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur