Dimplex CXLS24 Manuel utilisateur

Installation Instructions

Dimplex Ultra-Slim Storage and Convector Heaters

Twin Sensor Automatic Models CXLS12N, CXLS18N, CXLS24N

(85317 Iss. 16)

Bricks are in

packs of two.

The pack catalogue

number is XT 8300

CXLS12N - 12kWh

8 Bricks (4 Packs)

CXLS18N - 18kWh

12 Bricks (6 Packs)

CXLS24N - 24kWh

16 Bricks (8 Packs)

This product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3.

These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC

IMPORTANT - These instructions should be read carefully and retained for

future reference.

Note also the information given on the appliance.

The Installation must be carried out by trained personnel.•

A means for disconnection must be incorporated in the ﬁxed wiring by a double pole switch•

with a contact separation of a minimum of 3mm and in accordance with the current IEE Wiring

Regulations.

The heater must not be installed immediately below a ﬁxed socket outlet.•

The heater is not suitable for connection to a 30A ring circuit.•

Do not position the heater under windows where curtains can contact the heater casing.•

To maintain stability, it is essential that the heater is placed on a level surface and care should•

be taken to avoid irregular surfaces, such as may result from carpets or tiled surrounds partially

protruding under the heater.

Only heat resisting cable (minimum rating T85) should be used.•

If used in a bathroom the heater must be installed such that switches and other controls•

cannot be touched by a person in the bath or shower.

During any reassembly of the heater if a part of the thermal insulation shows damage or•

deterioration which may impair safety, it should be replaced with an identical part.

WARNING - In order to avoid overheating, do not cover the surfaces of the heater.•

Do not put clothes, fabrics or any other materials on the heaters.•

Do not place objects in contact with the heater.•

Do not position the heater where objects can come within 250mm (10”) of the top and 75mm•

(3”) of the sides of the heater.

CAUTION – Some parts of this product can become very hot and cause burns.•

Particular attention has to be given where children and vulnerable people are present.•

This appliance can be used by children from 8 years and above and persons with reduced•

physical, sensory or mental capabilities or lack of experience and knowledge, if they have

been given supervision or instruction concerning the use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the appliance.

Children less than 8 years of age should be kept away unless continuously supervised.•

IMPORTANT - Due to the newness of materials the heater will produce a smell for the ﬁrst•

few days of operation. Rooms must be well ventilated and young children, caged birds or

people with respiratory complaints must not remain in proximity to the heater for the ﬁrst 48

hours of the commissioning period.

1. Invert carton and lift carton off heater. Take care to ensure that staples

in carton !aps do not scratch surface of heater. Do not remove internal

packaging pieces at this stage.

Assembly of heater

2. Remove feet and accessories bag from corner "ttings (accessories bag

is located within one of the feet.)

3. Secure feet to base of the heater using two Taptite screws (provided)

for each foot. (On modules CXL12N/CXLS12N it would be necessary to

remove base corner packaging pieces to locate feet in position). Apply

end pressure whilst turning screws so that they form their own thread in

the plunged holes in the base.

4. Loosen hexagon head front panel securing screws, by 1-2 turns using

screwdriver through aperture in each end packaging piece.

Stand heater on its feet and remove all packaging pieces.

5. Position heater against wall in intended "nal position, taking

note of the minimum "xing dimensions given below. If "tted, the

Dimplex storage heater shelf should be "xed in accordance with

the instructions enclosed with the shelf.

Special instructions for !tting the heater to the wall.

6. Fitting on the top of carpet. If the heater is to stand on top of the carpet the following

course of action MUST be taken. Ensure that any carpet gripper (e.g. “Gripperod”) is

removed from the !nal positions of the storage heater feet. Ensure that the carpet AND

underlay completely cover the area under the feet so that they stand on a level surface.

If the underlay is particularly thick it is advisable to cut it away completely from under the

feet and for a suf!ciently wide area around the feet for them to rest !rmly through the

carpet onto the "oor.

7.Fitting directly on the "oor. If the !oor is carpeted then the carpet

may be slit and underlay cut away to allow the feet to rest "rmly on the

!oor. Carpet gripper must be locally removed so that the feet may rest in

a level position.

8. Having decided on the method of standing the heater on the !oor the

position of the wall bracket should be marked on the wall.

9. Remove wall "xing bracket from heater by removing the screws and

spacer bushes at each end.

11. Solid Brick/High Density Block Walls. (See step 12 if walls are of

low density block) These must be drilled and plugged with the No. 10 size

plastic inserts provided. The correct size of drill (8mm) should be used and

the hole should be drilled to a depth of 15mm greater than the length of the

plastic insert, so that the "xing is made below the plaster layer.

12. Low Density Block Walls. A specialised "xing, such as the Uni"x LB70.

should be employed following closely the manufacture’s instructions.

Panelled Internal Walls. Here it is best to locate the studding and use

No.10 size woodscrews. Where it is not possible to locate the studding

use type M5 Rawlplug INTERSETS on securely fastened plasterboard

panelling. For other wall panel materials the wall panel manufacturer should

be consulted for details of suitable wall "xing devices.

10. Four "xing positions must be chosen for the 24N, three

for the 18N and two for the 12N . Mark the positions for

the "xing holes - two at the extreme ends and the others

spaced evenly between them. Remove the bracket from

the wall, drill the holes in the positions marked, and insert

suitable "xings detailed in Steps 11 and 12. Secure the

wall bracket to the wall.

13. At this point determine which side of the heater off peak and on peak

supplies are to be connected. If off peak supply is to be connected from

the right hand end and on peak from left hand end proceed to next step.

If wiring of the building does not correspond with these cable entry points

then it will be necessary to secure the cable to the base of the rear of the

heater using the ties supplied in the "xing kit, ensure there is suf"cient

cable free to make connection easier later on.

14. Secure the heater to wall "xing bracket by replacing the two screws

and spacer bushes removed in step 11. The feet and wall mounting ar-

rangement are designed to accommodate skirting board sizes up to 25mm

(1”) thick. To avoid obstructing the air"ow to the rear of the heater the

following must be strictly adhered to:

(a) For skirtings higher than 100mm (4”) it will be necessary to position

the heater with the screws attached through the alternative "xing slots to

the front.

(b) For skirtings have a height in excess of 150mm (6”) it will be necessary

to reduce the height of the skirting to 150mm (6”) over the entire length of

the heater plus 25mm (1”) at either end.

15. Remove bottom front panel securing screws. These were loosened in

step 3 and should be easily unscrewed by hand.

16. Pull bottom of front panel forward to disengage the location pegs from

the side panels and clear it from bottom of heater.

17. Still holding bottom of front panel forward, lift upwards (1), to disengage

top edge of front panel from groove on heater top panel and remove front

panel from heater (2).

18. Remove the screw securing the convector controls bracket to the side

panel along with the spacer, nut and washer, taking care to ensure that

the retaining nut is not dropped

19. Remove the convector circuit mains block and insulation card from

the left side of the base panel. Unclip the wires running across the heater

below the inner front.

20. Remove screws retaining front inner skin.

21. Carefully lift the bottom of the front inner skin panel out of the retaining

!ange at the base of the heater, taking care not to damage the insulation,

hydraulic thermostat probe, heating elements and other vulnerable

components attached to this panel.

22. Remove the internal packing by sliding it up and off the elements, taking

care not to damage the insulation.

23. Remove one element to allow access for the back row of bricks. On the

CXL24N/CXLS24N remove the element to right of centre, on the CXL18N/

CXLS18N remove the central element and on the CXL12N/CXLS12N

remove the left hand element. Loosen the two screws securing the element

tails in the ceramic block, and lift the element up and out of the heater.

24. Position the bottom rear layer of bricks with the airway restrictions

coincident with the air slots in the base insulation slab. Push the bricks

"rmly to the back of the heater. Fit the top rear row of bricks, with the

airway restrictions uppermost.

25. Replace the element which had been removed by carefully passing

the ends through the base insulation slots into the terminal blocks below.

Position the insulator on the element end in contact with the terminal block

ceramic as shown, and tighten the connection screws. At this point check

that all element connections are tight. 26. Fit the front bricks with the airways facing inwards

27. Re-"t the front panel/insulation assembly, ensuring the bottom edge

of the panel is located behind the base !ange.

28. Make sure all screws removed in operation 20 are replaced

securely.

29. Replace the spacer nut, washer and screw removed in 18 and reconnect

the two quick connect terminals removed in 19.

30. Connect the off peak supply to the storage terminal block at the right

side of the base panel.

Replace the convector terminal block and insulation card at the left side

of the base panel, clip wires running across heater and connect peak

supply.

HEAT RESISTING CABLE MUST BE USED.

NOTE: ON NO ACCOUNT SHOULD SURPLUS CABLE BE STUFFED

INSIDE THE HEATER. Make sure clamp is tightening on outer sheath

of cable and not on individual conductors.

WARNING: THIS APPLIANCE MUST BE EARTHED. CHECK ALL

ELECTRICAL CONNECTIONS FOR TIGHTNESS.

ENSURE THAT CABLE CLAMP IS

SECURELY ATTACHED TO THE

CHASSIS OF THE HEATER.

31. Check that the damper mechanism within the heater functions freely,

by rotating the left hand control knob. Check also that the right hand (input)

knob rotates freely.

32. Select the convector heater load appropriate to your recommended

heating design scheme by, if necessary, disconnecting one convector

element by moving either the brown or mauve wire to the empty barrel on

the white terminal block on the internal baf!e.

Model

#CXL12N/CXLS12N

#CXL18N/CXLS18N

CXL24N/CXLS24N

Brown Wire

Still in Circuit

(Upper Element)

450W

650W

Mauve Wire

Still in Circuit

(Lower Element)

450W

1000W

1350W

Both in

Circuit

900W

1450W

2000W

#Note: if the heater is situated underneath a shelf or overhand up to 250mm

high, then the brown wire should remain in circuit.

33. Holding the bottom edge if the front panel towards you, locate the top

edge of the front panel in the groove at the top of the heater and ensure

that the locating pegs on the rear !anges of the front panel are located in

the receiving holes in each side panel.

34. Push the bottom of the front panel towards the heater, such that the

bottom !ange locates under the base.

35. Replace the two front panel securing screws removed in operation 15. A small mirror

placed on the "oor under the heater will help location of the threaded holes in the base. These

may be screwed in by hand most of the way, but should then be tightened using an 8mm AF

socket or open ended spanner.

36. Ensuring the electricity supply is disconnected, connect the free end of

the mains cable to a suitable double-pole witch adjacent to the appliance

- reinstate the electricity supply.

NOTE: The double pole witch must have a contact separation at least

3mm in all poles.

Peak Circuit Diagram

CXL12N & 18N

CXLS12N & 18N

BROWN

CUT-OUT

MAUVE

BLUEBLUE

BLUE

BROWN

MAUVE

BROWN

CONVECTOR

ELEMENT

CONVECTOR

ELEMENT

SELECTOR

BLOCK

MAINS

BLOCK

‘L’

‘N’

SWITCH

NEON

AIR

SENSING

STAT

Peak Circuit Diagram

CXL24N

CXLS24N

BROWN

CUT-OUT

MAUVE

BLUEBLUE

BLUE

BROWN

MAUVE

BROWN

CONVECTOR

ELEMENT

CONVECTOR

ELEMENT

SELECTOR

BLOCK

MAINS

BLOCK

‘L’

SWITCH

NEON

AIR

SENSING

STAT

BROWN

STAT

‘N’

Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing.

A division of the GDC Group Ltd, Millbrook House, Grange Drive, Hedge End, Southampton SO30 2DF

Dimplex,

Millbrook House,

Grange Drive,

Hedge End,

Southampton, SO30 2DF.

Customer Help Line: 0844 879 3588

Fax: 0844 879 3583

Email: [email protected]

Website: www.dimplex.co.uk

Table des matières

Autres manuels Dimplex Chauffage

Dimplex

Dimplex DHOP1341 Manuel utilisateur

Dimplex

Dimplex DXU2LCD Manuel utilisateur

Dimplex

Dimplex LS 200 Manuel utilisateur

Dimplex

Dimplex OFX750 Manuel utilisateur

Dimplex

Dimplex Electricaire R7 Manuel utilisateur

Dimplex

Dimplex LPC Series Manuel utilisateur

Dimplex

Dimplex OFRC10ECCb Manuel utilisateur

Dimplex

Dimplex PLX 500 Manuel utilisateur

Dimplex

Dimplex RPX Series Manuel utilisateur

Dimplex

Dimplex DPH1563 Manuel utilisateur

Dimplex

Dimplex KSE 050 Manuel utilisateur

Dimplex

Dimplex RFV-800 Manuel utilisateur

Dimplex

Dimplex SRX 080M Manuel utilisateur

Dimplex

Dimplex EPX Series Manuel utilisateur

Dimplex

Dimplex OFC1500TLG Manuel utilisateur

Dimplex

Dimplex CEL50 Manuel utilisateur

Dimplex

Dimplex SAF6 Series Manuel utilisateur

Dimplex

Dimplex XHD23L-AU-RL Manuel utilisateur

Dimplex

Dimplex CXLS12N Manuel utilisateur

Dimplex

Dimplex OFRC10BLK Manuel utilisateur

Dimplex

Dimplex SRX 070C Manuel utilisateur

Dimplex

Dimplex OFX075l OFX100 Manuel utilisateur

Dimplex

Dimplex PCH2000TCW Manuel utilisateur

Dimplex

Dimplex EF 6/20 Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur