Digitus DN-95301 Manuel utilisateur

Autres manuels pour DN-95301

1

Table des matières

Autres manuels Digitus Changer

Digitus

Digitus DN-80071 BLACK RAPID 1000 Manuel utilisateur

Digitus

Digitus DN-95320 Manuel utilisateur

Digitus

Digitus DS-45341 Manuel utilisateur

Digitus

Digitus DS-12901 Manuel utilisateur

Digitus

Digitus Desktop 4-PortAudio-Combo-KVM Switch Manuel utilisateur

Digitus

Digitus DS-11200-1 Manuel utilisateur

Digitus

Digitus DA-73301 Manuel utilisateur

Digitus

Digitus DA-70242-1 Manuel utilisateur

Digitus

Digitus DN-80066 Manuel utilisateur

Digitus

Digitus 16 PORT GIGABIT ETHERNET NETWORK SWITCH Manuel utilisateur

Digitus

Digitus DN-652120 Manuel utilisateur

Digitus

Digitus DS-15202 Manuel utilisateur

Digitus

Digitus DS-44100-1 Manuel utilisateur

Digitus

Digitus DA-70231 Manuel utilisateur

Digitus

Digitus DA-70255 Manuel utilisateur

Digitus

Digitus DN-95140 Manuel utilisateur

Digitus

Digitus DS-50304 Manuel utilisateur

Digitus

Digitus DS-12910 Manuel utilisateur

Digitus

Digitus DN-80115 Manuel utilisateur

Digitus

Digitus 4-Port Desktop USB KVM Switch with USB 2.0... Manuel utilisateur

Digitus

Digitus DS-45329 Manuel utilisateur

Digitus

Digitus DS-45312 Manuel utilisateur

Digitus

Digitus DN-8021B Manuel utilisateur

Digitus

Digitus DS-12891 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

Quick Installation Guide

Installing the Switch

The switch is designed for office use, where it can be free standing, desktop-mounted,

or mounted in most standard 19-inch equipment racks. If you prefer, you can rack-

mount the switch in a wiring closet or equipment room using two mounting brackets and

six screws.

When choosing a location for the switch, observe the following guidelines:

Make sure the switch is accessible and that the cables can be connected easily.

Keep cabling away from sources of electrical noise such as radios, transmitters, and

broadband amplifiers as well as power lines and fluorescent lighting fixtures.

Prevent water or moisture from entering the switch case.

Make sure there are no obstructions to restrict airflow around the switch. We

recommend that you provide a minimum of 50 millimeter (2-inch) clearance.

Do not place liquids or other objects on top of the switch.

If the switches are freestanding, do not stack more than four switches on top of one

another.

Pre-Installation Considerations

Fast Ethernet Topology Considerations

If you will be using the switch for Fast Ethernet (100 Mbps) operation, observe the

following guidelines:

The maximum unshielded twisted-pair (UTP) cable length is 100 meters (328 feet)

over Category 5 cable.

Single-repeater topologies permit a total network span of 325 meters (1066 feet).

Full-Duplex Considerations

The switch provides full-duplex support for its Fast Ethernet ports. Full-duplex operation

allows frames to be sent and received simultaneously, doubling a link’s potential data

throughput. If you will be using the switch in full-duplex mode, the maximum UTP cable

length is 100 meters (328 feet) over Category 5 cable.

Desktop or Shelf Mounting

To install the switch on a desktop or shelf, simply complete the following steps:

Step 1 Place the switch on a desktop or shelf near an AC power source.

Step 2 Keep enough ventilation space between the switch and the surrounding objects.

Step 3 Connect the switch to network devices.

A. Connect one end of a standard network cable to the 10/100 RJ-45

ports on the front of the switch.

B. Connect the other end of the cable to the network devices such as

printer servers, workstations or routers.

Note: It is strongly recommended to use the UTP Category 5 network cabling with RJ-

45 tips for the network connection.

Step 4 Supply power to the switch.

A. Connect one end of the power cable to the switch.

B. Connect the power cube end of the power cable to a standard wall

outlet.

When the switch receives power, the Power LED should remain solid Green.

Rack-Mounting

The following procedure describes how to install the switch in a standard 19-inch rack.

Disconnect all cables from the switch.

Remove all adhesive pads from the bottom of the switch.

Step 1 Place the switch right side up on a hard flat surface, with the front panel facing

you.

Step 2 Locate a mounting bracket over the mounting holes on one side of the switch

Step 3 Insert three screws and use a screwdriver to secure.

Step 4 Repeat the two previous steps for the other side of the switch.

Step 5 Insert the switch into the 19-inch rack and secure with suitable screws. Make

sure the ventilation holes on the switch are not obstructed.

Step 6 Connect the network cable and supply power to the switch.

Figure 1 Locating a Mounting Bracket