Digitus professional DS-23200-2 Manuel utilisateur

8 ports/16 ports

USB/PS/2 Combo-KVM Switch

Manual

DS-23200-2 • DS-23300-2

PRODUCT MODEL LIST

Model Specification

DS-23200-2 8 input (USB & PS/2), 1 output (USB), Supporting cascade

& hub.

DS-23300-2 16 input (USB & PS/2), 1 output (USB), Supporting

cascade & hub.

Please check to make sure that all the components are present and that nothing

was damaged in shipping. If you encounter a problem, contact your dealer.

Read this manual thoroughly and follow the installation and operation procedure

carefully to prevent any damage to the unit, and/or any of the devices that

connect to it.

PRODUCT MODEL LIST ..........................................................................................2

PACKING LIST.........................................................................................................3

OVERVIEW.............................................................................................................3

FEATURES ..............................................................................................................4

HARDWARE REQUIREMENT ..................................................................................4

Operation System.........................................................................................5

INTRODUCTION.....................................................................................................7

Front View ....................................................................................................7

Rear View .....................................................................................................8

INSTALLATION........................................................................................................9

Single KVM device installation .....................................................................9

Cascade device connection ........................................................................11

OPERATION ......................................................................................................... 12

OSD OPERATION..................................................................................................13

TROUBLESHOOTING ............................................................................................22

SPECIFICATION ....................................................................................................22

SAFE GUIDE: ........................................................................................................24

OVERVIEW

8 ports/16 ports USB/PS/2 KVM (Keyboard, Video, Mouse) Switches are control units

that allow access and control of up to 8 (DS-23200-2) or 16 (DS-23300-2) computers

from a single USB/keyboard, USB/mouse, and monitor console.

There are two convenient methods to access any computer connected to the

installation: (1) using the push button port selection switches located on each unit’s

front panel; (2) selecting from menus provided by the On Screen Display (OSD).

Setup is fast and easy: simply plug cables into their appropriate ports. There is no

software to configure, and no incompatible problems. It works on multiple operating

platforms (PC compatible, Sun, etc.).

There is no better way to save time and money than with a DS-23200-2/DS-23300-2

Installation: Since a single console manages all of the computers, the

DS-23200-2/DS-23300-2 setup (1) eliminates the expense of having to purchase a

separate keyboard, monitor, and mouse for each computer; (2) saves all the space

those extra components would take up; (3) saves on energy costs; (4) eliminates the

inconvenience and wasted effort involved in constantly moving from one computer to

another.

PACKING LIST

The complete 8 ports/16 ports USB/PS/2 KVM switch package consists of:

8 ports/16 ports USB/PS/2 KVM switch

Power Adapter

User Manual

FEATURES

One console controls 8 or 16 computers

Be compatible with USB/keyboard and mouse in console and PS/2, USB

keyboard and mouse in computer

Computer selection via front panel switches and OSD

LEDs display for easy status monitoring

Auto Scan Mode for monitoring all computers

Superior video quality

Easy installation – no software required

Hot pluggable – add or remove computers for maintenance without powering

down the switch

Support Windows, Solaris etc.

HARDWARE REQUIREMENT

CONSOLE

A VGA, SVGA monitor capable of the highest resolution that you will be using

on any computer in the installation

A USB/mouse

A USB/keyboard

COMPUTER

The following equipment must be installed on each computer:

A VGA, SVGA card

PS/2, USB keyboard and mouse ports

OPERATION SYSTEM

Operation System Version

Windows Windows 2000/XP/2003/2008/Vista/7/10

Linux RedHat 9.0 or higher

SuSE 10/11.1 or higher

Debian 3.1/4.0

Ubuntu 7.04/7.10

UNIX AIX 4.3 or higher

FreeBSD 5.5 or higher

Sun Solaris 8 or higher

Mac OS 9.0~10.6 (Snow Leopard)

Novell Netware 6.0 or higher

More operating system support, please pay attention to the latest version of the

relevant product compatibility.

CABLE

Only customized KVM cable sets, which are specially designed to work with these

switched, may be used. To purchase DIGITUS KVM cable sets, contact your dealer.

VGA+ USB (Type A)+ PS/2 Keyboard (Purple) +PS/2 Mouse (Green)

INTRODUCTION

Front View

8 ports selection switches

16 ports selection switches

1&2 3

No. Section Function

1 Port Selection

Switches

Press a switch button to access the computer attached to its

corresponding port. The internal buzzer beeps, it means that

the switching action is performed correctly, The selected port

LED will light up as well.

2 Port LEDs The port LEDs are built into the Port Selection Switches. The

upper ones are the On Line LEDs; the lower ones are the

Selected Port LEDs:

The On Line LEDs light RED to indicate that the computer

attached to the corresponding port is up and running.

The Selected LEDs light GREEN to indicate that the

computer that attached to the corresponding port is the

one that has the KVM focus.

3 Reset If KVM has no responding, plug needle or ballpoint pen into

the hole to reset KVM

Rear View

8 port KVM rear view

5 3 4

16 port rear view

6 2 1

No. Section Function

1 KVM

Connection

Port

Port to connect computer. Connect one end of the VGA

connector of the corresponding KVM cable to this, and the

other end of the keyboard connector to the port

corresponding to the PC. (Refer to the description of

"Cable" in the relevant section.)

2 VGA port Connect the VGA cable from the control panel to this port.

3 USB Keyboard,

Mouse port

Plug your USB keyboard, USB mouse. USB Type A

(Optional)

4 PS/2 Keyboard,

Mouse port

Plug your PS/2 keyboard, PS/2 mouse (Optional)

5 IP Remote

Control Part

To provide users with remote network control. (Refer to

the instruction manual of the module product for specific

operation.) (Optional)

6 Supply hub Plug the power adapter here.

If you purchase the product does not contain IP expansion module is similar to the

product shown below.

DS-51000-1 No IP Module Rear View

The part marked with “DS-55100-1” is the external baffle of the extended IP module,

and it needs to be removed and replaced to install the IP module.

INSTALLATION

Single KVM device installation

Note: Before installation, make sure that the equipment is powered off. To prevent

damage to the equipment during installation, make sure that all the devices installed

are well grounded.

To install a single-level KVM, refer to the following online diagrams (numbered in the

order of steps on the online graph) and operate as per bellowing:

1. Plug your USB keyboard, mouse, or PS/2 keyboard and mouse into the USB or

PS/2 console port on the rear of the switch.

2. Connect the VGA monitor's video signal cable to the VGA console port and turn

on the power.

3. Plug the VGA connector into the VGA port of any available VGA port on the

switch by using a set of KVM cables corresponding to the product model.

4. Connect the corresponding VGA video connector, USB or PS/2 connector of the

KVM cable to the corresponding PC port.

5. Plug the power adapter supplied with this package into the AC power supply,

and plugs the other end of the power adapter into the power jack on the

switch.

6. Connect the network cable to the IP port of the IP module. (Optional)

7. Turn on the computer.

Note:

1. Make sure all plugs are connected to the same set of KVM port jacks (all on port 1,

or all on port 2).

2. The IP module is an optional module of the product. If the product you purchased

does not contain the module, please ignore the related operation in Step 6.

3. Before using the IP module, please make the corresponding configuration and

network debugging, and then connect to the network you want to connect.

Otherwise, the IP module may not be able to control normally because of the

connection failure. (Refer to the manual of the IP module product manual for how

to use and debug the IP module.)

USB OR PS2

Net

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Digitus professional Changer

Digitus professional

Digitus professional DS-72210 Manuel utilisateur

Digitus professional

Digitus professional DN-651107 Manuel utilisateur

Digitus professional

Digitus professional DN-80065 Manuel utilisateur

Digitus professional

Digitus professional DN-80114 Manuel utilisateur

Digitus professional

Digitus professional DN-651108 Manuel utilisateur

Digitus professional

Digitus professional DN-95342 Manuel utilisateur

Digitus professional

Digitus professional DN-80111 Manuel utilisateur

Digitus professional

Digitus professional DN-95115 Manuel utilisateur

Digitus professional

Digitus professional DN-65 Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur