DigitaLinx DL-44E-KIT Mode d'emploi

11675 Ridgeline Dr

Colorado Springs, CO 80921

Rev 160926 Phone: 719-260-0061

Toll-Free: 800-530-8998

Fax: 719-260-0075

DL-44E-KIT Installaon and

Operaon Guide

DL-44E-KIT Installaon Guide

Important Safety Instrucons

»Please completely read and verify you understand all instrucons in this manual before operang this equipment.

»Keep these instrucons in a safe, accessible place for future reference.

»Heed all warnings.

»Follow all instrucons.

»Do not use this apparatus near water.

»Clean only with a dry cloth.

»Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers)

that produce heat.

»Use only accessories specied or recommended by Intelix.

»Explanaon of graphical symbols:

◊ Lightning bolt/ash symbol: the lightning bolt/ash and arrowhead within an equilateral triangle

symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the

product enclosure which may be of sucient magnitude to constute a risk of shock to a person or

persons.

◊ Exclamaon point symbol: the exclamaon point within an equilateral triangle symbol is intended

to alert the user to the presence of important operang and maintenance (servicing) instrucons

in the literature accompanying the product.

»WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR

MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS.

»Use the mains plug to disconnect the apparatus from the mains.

»THE MAINS PLUG OF THE POWER CORD MUST REMAIN READILY ACCESSIBLE.

»Do not defeat the safety purpose polarized or grounding-type plug. A polarized plug has two blades with one wider

than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong

is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of

your obsolete outlet. Cauon! To reduce the risk of electrical shock, grounding of the center pin of this plug must be

maintained.

»Protect the power cord from being walked on or pinched parcularly at the plugs, convenience receptacles, and the

point where they exit from the apparatus.

»Do not block the air venlaon openings. Only mount the equipment per Intelix’s instrucons.

»Use only with the cart, stand, table, or rack specied by Intelix or sold with the equipment. When/if a

cart is used, use cauon when moving the cart/equipment combinaon to avoid injury from p-over.

»Unplug this apparatus during lightning storms or when unused for long periods of me.

»Cauon! Shock Hazard. Do not open the unit.

»Refer to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as

power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally, or has been dropped.

DL-44E-KIT Installaon Guide

Table of Contents

Product Overview�� 6

Package Contents �� 6

Front and Rear Panels DL-44E-KIT�� 7

Front Panel�� 7

Rear Panel �� 7

Front and Rear Panels DL-HD70LS-RX �� 8

Front Panel�� 8

Rear Panel �� 8

Installaon Instrucons�� 9

Mount the Matrix �� 9

Usage Precauons �� 9

Connecon Procedure�� 9

Connecon with HDBaseT Receiver �� 9

System Operaons ��10

IR Remote�� 10

Control Far-end Device locally��11

Control Local Device Remotely ....................................................................................................................11

Mulple to Mulple: (IR Matrix) .................................................................................................................11

TCP/IP Control �� 12

Controlled by PC�� 12

Controlled by PC(s) in LAN��12

Web Browser Control�� 13

EDID Management �� 14

EDID learning ��14

EDID Invoking�� 14

RS232 Commands�� 15

Troubleshoong �� 19

Loss of color or no video signal output ��19

Cannot control the device via front panel buons��19

Cannot control the device via IR remote �� 19

Cannot control the matrix by control device (e.g. a PC) through RS232 port��19

Stac becomes stronger when connecng the video connectors ��19

DL-44E-KIT Technical Specicaons�� 20

DL-HD70LS-RX Technical Specicaons �� 21

DL-44E-KIT Installaon Guide

The DL-44E-KIT is a professional 4K HDBaseT Home Distribuon Hub Kit, which consists of a 4K HDBaseT Matrix

Switcher, 3 HDBaseT Receivers and accessories. The DL-44E-KIT is a professional 4x4 HDBaseT Matrix Switcher

that consist of the following inputs and outputs, 4 HDMI IN (4kx2K@60Hz signal at max), 3 IR IN, 1 IR EYE, 4 IR

OUT, 3 HDBaseT OUT, 1 HDMI OUT, 1 SPDIF OUT, 1 L&R RCA OUT, and TCP/IP, RS232 control port via phoenix

connector. The DL-44E-KIT oers manual HDCP management and auto-detecng along with easy installaon

with rack-mounng design.

The DL-HD70LS-RX is an HDBaseT Receiver that consists of the following inputs and outputs, 1 HDBaseT IN,

1 IR IN, 1 IR OUT and HDMI OUT. The receiver is powered directly by the DL-44E-KIT. All HDMI inputs can be

selected by either the front panel buons, IR, RS232 or GUI. The selected source is delivered to HDBaseT zoned

outputs 1-3 & HDMI Output.

The DL-44E-KIT is capable of delivering 4K signals up to 40m, 1080p up to 70m and powering the receivers via

a single CAT5e cable. It is recommended to use good quality CAT6 cable. The Matrix Switcher supports EDID

management and is HDCP 2.2, 1.4 compliant. Audio sources can be selected via RS232 commands and TCP/IP

at the Matrix Switcher or by 3rd Party control.

Product Overview

Package Contents

Please verify the following items are in the shipping box prior to installaon of the DL-44E-KIT.

1 x DL-44E-KIT 4K HDBaseT Matrix Switcher,

3 x DL-HD70LS-RX HDBaseT Receivers

1 x Power Adapter (DC 24V 2.71A)

1 x Power Cord(Oponal)

4 x IR Emiers

3 x IR Receivers

1 x IR Receiver(Inserted into IR EYE port)

1 x IR remote

1 x RS232 cable(Phoenix to 9-pin D-Sub)

2 x Mounng ears & 6 x Screws (For DL-44E-KIT 4K HDBaseT Matrix Switcher )

DL-44E-KIT Installaon Guide

DL-44E-KIT Front and Rear Panels

Front Panel

Rear Panel

FIRMWARE

OUTPUT 1

IN PUT TO

1 2 3 4

OUTPUT 2

IN PUT TO

1 2 3 4

OUTPUT 3

IN PUT TO

1 2 3 4

OUTPUT 4

IN PUT TO

1 2 3 4

1-HDBT

IR OUT

IR E YE

2-HD BT 4-SPDIF4-HDMI

3- HDBT L R

4 DC 24V TCP/I P

RxTx

RS 232

POWER CONTR OL

IR IN

1 2 3

HD MI 1 HD MI 2 HD MI 3 H DMI 4

INPUTS OUTPUTS

1. FIRMWARE

2. Power Indicator

3. INPUT Selector Indicators

4. Output selector buon

1. HDMI INPUTS

2. IR IN

3. IR OUT

4. OUTPUTS

5. TCP/IP and RS232 Control

6. DC 24V

DL-44E-KIT Installaon Guide

DL-HD70LS-RX Front and Rear Panels

Front Panel

Rear Panel

IR IN IR OUTHDMI OUT

123

Link HDCP

12V DC

1. HDMI OUT

2. IR IN

3. IR OUT

1. Power Indicator

2. TP IN

The RJ45 socket has two LED status indicators. Plug in the Pre-installed CAT cable in to the HDBT RJ45 socket.

HDCP: HDCP compliant indicator, OFF: No HDMI trac (no picture), GREEN: Signals with HDCP, Blinking GREEN:

Signal without HDCP.

LINK: HDBT Link status indicator. OFF: No Link, YELLOW:Link Successful, Blinking YELLOW: Link Error.

DL-44E-KIT Installaon Guide

Installaon Instrucons

Mount the Matrix

At least 2 inches of free air space is required on both sides of the DL-44E-KIT for proper side venlaon. Avoid

mounng the DL-44E-KIT near a power amplier or any other source of signicant heat.

1. The DL-44E-KIT 4K Home Distribuon kit should be installed in a clean and dust free environment.

2. Ensure that all plugs, power cords and sockets are in good condion without signs of damage.

3. All devices should be connected before power on.

Usage Precauons:

Connecon Procedure:

1. Connect HDMI sources (e.g. DVD) to HDMI input ports of the Matrix Switcher via good quality HDMI

cables.

2. Connect the Pre-Installed CAT5e/CAT 6 cable infrastructure to the DL-44E-KIT Matrix Switcher and

HDBaseT receivers DL-HD70LS-RX via good quality patch leads.

3. Connect HDTV to HDMI output port via HDMI cable.

4. Plug in an HDMI cable in to each of the DL-HD70LS-RX and connect to the local display [HDTV].

5. Connect AVR amplier to SPDIF output port or via the Toslink opc bre cable.

6. Connect speaker to L&R (RCA) output port via audio cable.

7. Plug the IR Receivers 3.5mm jack into the IR IN sockets on the DL-HD70LS-RX and plug in the IR Emiers

to the IR OUT sockets (1-4) on the Matrix Switcher to make up as an IR Matrix.

8. Plug the phoenix connector in to the RS232 socket on the matrix, this will enable the Matrix Switcher to

be controlled via a PC.

9. Plug in a Patch lead from the router in to the Ethernet port on Matrix Switcher to control Matrix Switcher

by TCP/IP protocol.

10. Plug in the Power supply adapter 24V DC and ghten to secure. Once all components have been

connected and the installaon is completed, turn on the power.

Connecon with HDBaseT Receiver:

1. The Matrix Switcher has 3 HDBaseT outputs which support PoC technology.

2. Plug in the 4 RJ45 patch leads in to the HDBT outputs and connect to the pre-installed infrastructure.

3. Connect the DL-HD70LS-RX HDBaseT Receivers to the pre-installed cabling via addional patch leads.

4. Plug the power supply in to the power socket on the matrix, the DL-HD70LS-RX will be powered by the

Matrix Switcher.

DL-44E-KIT Installaon Guide

System Operaons

The Matrix Switcher can be controlled via the front panel. Please follow the basic programing instrucons

below:

1. To convert one input to an output:

Example: Input 1 to Output 3

-Press INPUTS 1 + OUTPUTS 3 + ENTER

2. To convert an input to several outputs:

Example: Convert Input 2 to Output 3 and 4

-Press INPUTS 2 + OUTPUTS 3 + OUTPUTS 4 + ENTER

3. To convert an input to all outputs:

Example: Input 1 to all Outputs

-Press INPUTS 1 + ALL + ENTER

IR Remote

Connect an IR receiver to the IR EYE port of the Matrix Switcher, users can control it through the included IR

remote. Here is a brief introducon to the IR remote.

Standby buon, press it to enter/ exit standby mode.

INPUTS: Input channel selecon buons, range from 1-4, corresponding IR signal switched

synchronously when switching input channels.

OUTPUTS: Output channel selecon buons.

Menu buons: ALL, EDID, CLEAR and ENTER.

-ALL: Select all outputs.

-EDID management buon: Enable input port to manually capture and learn the EDID data

of output devices.

-CLEAR: Withdraw an operaon like switching output channel, learning EDID data before it

comes into eect. Meanwhile, the matrix will return to the previous status.

-ENTER: Conrm operaon.

Table des matières

Autres manuels DigitaLinx Commutateur matriciel

DigitaLinx

DigitaLinx DL-HDM88-SS Mode d'emploi

DigitaLinx

DigitaLinx DL-HDM88A-H2 Manuel utilisateur

DigitaLinx

DigitaLinx DL-HDM44 Manuel utilisateur

DigitaLinx

DigitaLinx DL-A51 Manuel utilisateur

DigitaLinx

DigitaLinx DL-HDM88A-H2 Manuel utilisateur

DigitaLinx

DigitaLinx DL-S42-H2 Manuel utilisateur

DigitaLinx

DigitaLinx DL-HDM88-FS Mode d'emploi

DigitaLinx

DigitaLinx DL-HDM44-FS Mode d'emploi

DigitaLinx

DigitaLinx DL-A31 Manuel utilisateur

Manuels Commutateur matriciel populaires d'autres marques

Broadcast Tools

Broadcast Tools SS 8.2 Manuel utilisateur

Altimium

Altimium MATF32 Manuel utilisateur

ALFAtron

ALFAtron ALF-MUK44N Manuel utilisateur

Monoprice

Monoprice Blackbird 15377 Manuel utilisateur

Kramer

Kramer XL 3216VS Manuel utilisateur

PTN

PTN FMX12 Manuel utilisateur

CYP

CYP nT15GX01 Manuel utilisateur

Kramer

Kramer VP-2x2 Manuel utilisateur

Kramer

Kramer Sierra Video 6432V5xl Manuel utilisateur

TESmart

TESmart HMA0402A40 Manuel utilisateur

Octava

Octava HD4XSTPMX Manuel utilisateur

Intelix

Intelix FLX-88 Mode d'emploi

Kramer

Kramer LASSEN XL 3232S Manuel utilisateur

Roland

Roland XS-1HD Manuel utilisateur

Kramer

Kramer VS-66HDCPxl Manuel utilisateur

Atlona

Atlona AT-HDMI-22M Manuel utilisateur

Link

Link HD8X8 Manuel utilisateur

AMX

AMX AVS-OP-2020-117 Instructions et recettes