Digital Equipment DECpc AXP 150 Manuel d'utilisation
DECpcAXP150
COMPAQQVision1024/EController
UserInformation
Order Number: EK-A0653-UG.001
July 1993
This manual describes how to install, configure, and use the
COMPAQ QVision 1024/E controller in the DECpc AXP 150 system.
Revision Information: This is a new manual.
Digital Equipment Corporation
Maynard, Massachusetts
First Printing, July 1993
Possession, use, or copying of the software described in this documentation is
authorized only pursuant to a valid written license from Digital, an authorized,
sublicensor, or the identified licensor.
While Digital believes the information included in this publication is correct as
of the date of publication, it is subject to change without notice.
Digital Equipment Corporation makes no representations that the
interconnection of its products in the manner described in this document
will not infringe existing or future patent rights, nor do the descriptions
contained in this document imply the granting of licenses to make, use, or sell
equipment or software in accordance with the description.
© Digital Equipment Corporation 1993.
All Rights Reserved.
The postpaid Reader’s Comments form at the end of this document requests
your critical evaluation to assist in preparing future documentation.
The following are trademarks of Digital Equipment Corporation: AXP, DEC,
DECpc, Digital, VAX DOCUMENT, the AXP logo, and the DIGITAL logo.
COMPAQ is a registered trademark and QVision is a trademark of Compaq
Computer Corporation.
Windows NT is a trademark of Microsoft Corporation.
All other trademarks and registered trademarks are the property of their
respective holders.
This document was prepared using VAX DOCUMENT, Version 2.1.
FCC Notice: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio or television technician for
help.
Modifications
The FCC requires the user to be notified that any changes or modifications
made to this device that are not expressly approved by Compaq Computer
Corporation may void the user’s authority to operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic
RFI/EMI connector hoods to maintain compliance with FCC Rules and
Regulations.
This document was prepared using VAX DOCUMENT, Version 2.1.
Contents
Preface ..................................................... vii
1 Installing the QVision Controller
Introduction . . . ................................... 1–1
About the QVision 1024/E Controller ................... 1–1
In This Chapter ................................... 1–1
Installing the QVision Controller ......................... 1–2
Before You Begin .................................. 1–2
Setting the Switch ................................. 1–2
Installation Procedure . . . ........................... 1–2
QVision Controller Illustration........................ 1–3
Connecting the Monitor ................................ 1–4
Important Information . . . ........................... 1–4
Connection Procedure . . . ........................... 1–4
2 Configuring the QVision Controller
Introduction . . . ................................... 2–1
In This Chapter ................................... 2–1
EISA Configuration Utility (ECU) ........................ 2–2
Running the ECU ................................. 2–2
Changing the Configuration .......................... 2–2
Default Configuration . . . ........................... 2–3
3 Troubleshooting
Summary ........................................ 3–1
Identifying and Solving Problems . . ................... 3–1
v
A Specifications
Introduction ...................................... A–1
In This Appendix . . ................................ A–1
QVision Controller Specification . . ........................ A–2
QVision Controller Specification Summary .............. A–2
SVGA Connector Pin Specification ........................ A–3
Summary ........................................ A–3
SVGA Connector Illustration . ........................ A–3
SVGA Connector Pin Specification ..................... A–3
Index
Figures
1–1 QVision 1024/E Controller Switches .................... 1–3
1–2 Connecting the Monitor ............................. 1–4
A–1 SVGA Connector . . ................................ A–3
Tables
2–1 Configuration Settings .............................. 2–2
2–2 Default Configuration .............................. 2–3
3–1 Troubleshooting Table .............................. 3–1
A–1 Specification Table . ................................ A–2
A–2 SVGA Connector Pin Specification ..................... A–3
vi
Preface
Purpose of This
Manual This manual describes how to install, configure, and use the
COMPAQ® QVision™ 1024/E controller in the DECpc™ AXP™
150 system.
Audience This manual is intended for anyone installing, configuring,
or connecting the COMPAQ QVision 1024/E controller in a
DECpc AXP 150 system. It is written for both experienced and
inexperienced users.
Structure of
This Manual This manual contains three chapters, an appendix, and an index
as follows:
• Chapter 1 describes how to install and connect the QVision
controller.
• Chapter 2 describes how to configure the system after you
have installed the QVision controller.
• Chapter 3 contains troubleshooting information.
• Appendix A lists the specifications for the QVision controller.
• The index is a reference to the main topics in the manual.
Associated
Information The DECpc AXP 150 and DEC 2000 Model 300 AXP Customer
Technical Information manual contains associated information.
vii
Conventions The following conventions are used in this manual:
Convention Description
monospace
Text displayed on the screen is shown in
monospace type.
italic type Italic type emphasizes important information,
indicates variables, and indicates complete
titles of manuals.
n.nn
A period in numerals signals the decimal point
indicator. For example, 1.75 equals one and
three-fourths.
nA lowercase italic nindicates the generic use
of a number. For example, 19nn indicates a
4-digit number in which the last 2 digits are
unknown.
Note A note contains information of special
importance to the reader.
viii
1
Installing the QVision Controller
Introduction This chapter describes how to install and connect the QVision
1024/E controller.
About the
QVision 1024/E
Controller
The QVision 1024/E controller is used in an EISA-based personal
computer or system. It allows you to connect a super video
graphics array (SVGA) monitor to the system. You can install
multiple QVision controllers in a system unit. The QVision
controller contains a switch that allows you to select the QVision
controller to be the primary video controller or the secondary
video controller.
In This Chapter This chapter contains the following sections:
• Installing the QVision Controller
• Connecting the Monitor
Installing the QVision Controller 1–1
Installing the QVision Controller
Installing the QVision Controller
Before You
Begin The QVision 1024/E controller contains a switch that you must
set to either the primary or secondary switch setting, depending
on the number of QVision controllers you are installing. This
switch is located on the switch panel SW1 on the QVision
controller. Figure 1–1 shows the location of this switch.
Setting the
Switch If you are installing one QVision 1024/E controller, set switch 1
on the board to the primary (PRIM) setting. If you are installing
more than one QVision 1024/E controller, set switch 1 to the
primary setting on one QVision controller and to the secondary
(SECOND) setting on all other QVision controllers.
Installation
Procedure For information on opening the system unit and installing an
option board, see the DECpc AXP 150 and DEC 2000 Model 300
AXP Customer Technical Information manual.
1–2 Installing the QVision Controller
Autres manuels pour DECpc AXP 150
3
Table des matières
Autres manuels Digital Equipment Ordinateur de bureau
Digital Equipment
Digital Equipment DECstation 5000/100 Series Manuel d'utilisation
Digital Equipment
Digital Equipment AlphaStation 600 Series Manuel
Digital Equipment
Digital Equipment DECstation 2100 Manuel
Digital Equipment
Digital Equipment DEC 3000 500X AXP Instructions d'utilisation et d'installation
Digital Equipment
Digital Equipment VAX 4000 100 Manuel de service
Digital Equipment
Digital Equipment Personal DECstation 5000 50 Manuel
Digital Equipment
Digital Equipment DECpc AXP 150 Manuel d'utilisation
Digital Equipment
Digital Equipment VAXstation 3100 Series Manuel d'installation et d'exploitation
Digital Equipment
Digital Equipment Alpha Manuel d'utilisation
Digital Equipment
Digital Equipment PDP-11/60 Manuel utilisateur
Digital Equipment
Digital Equipment VT420 Manuel utilisateur
Digital Equipment
Digital Equipment VAX 4000 500A Manuel utilisateur
Digital Equipment
Digital Equipment VAX 4000 Model 100 Guide de démarrage rapide
Digital Equipment
Digital Equipment PDP-11 Series Manuel utilisateur
Digital Equipment
Digital Equipment STARION 20 Series Manuel utilisateur
Digital Equipment
Digital Equipment VT420 Manuel utilisateur
Digital Equipment
Digital Equipment VAXstation 4000/90 Series Guide de l'utilisateur
Digital Equipment
Digital Equipment DECstation 212LP Manuel utilisateur
Digital Equipment
Digital Equipment VAXstation 4000/60 Instructions d'utilisation et d'installation
Digital Equipment
Digital Equipment DEC 3000 Manuel utilisateur
Digital Equipment
Digital Equipment DIGITAL Personal Workstation Manuel d'installation et d'exploitation
Digital Equipment
Digital Equipment VAX 4000 Model 300 Manuel utilisateur
Digital Equipment
Digital Equipment VAX 4000 Model 100 Guide de démarrage rapide
Digital Equipment
Digital Equipment VAX 4000 300 Manuel
