digicon Tx1500 Manuel utilisateur
Installation Manual
Turnstile
Tx1500
Copyright– Digicon S.A.
Controle Eletrônico para Mecânica – 2013
All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, translated into any
language or computer language in any electronic, magnetic, optical, chemical,
manual way, or otherwise, without the express written permission from
Digicon S.A.
Códe: 069.31.211
Version: 01
This manual was elaborated by:
Digicon S.A. Electronic Control for Mechanics Documentation Sector - EDS
Contents
1. IMPORTANT INSTRUCTIONS ................................................................
2. ORIENTATIONS .................................................................................
3. INTRODUCTION ................................................................................
4. INSTALLING Tx1500 ..........................................................................
5. CAPTIONS ........................................................................................
6. POWER SUPPLY .................................................................................
7. CONTROL BOARD ..............................................................................
7.1.INPUTS ..........................................................................................
7.2.OUTPUTS ........................................................................................
7.3.CONFIGURATION OF CONTROL BOARD - SWITCHES DS1 AND Ds2 .........
7.4.EXAMPLES OF SOME CONFIGURATIONS ..............................................
7.5. SERIAL COMMUNICATION ................................................................
8. DIMENSIONS ....................................................................................
9. WARRANTY AND TECHNICAL ASSISTANCE ............................................
Torniquete
Tx1500
05
06
06
07
23
25
25
27
28
30
30
31
32
33
1. mportant nstructionsI i
You can see, below, the symbols that will appear in this manual, signaling
important moments. It is essential to pay attention to them.
TIP: Indicates something Digicon considers important.
CAUTION: Indicates a moment of extreme caution when
handling the equipment/product
ATTENTION: Indicates a moment when your observation
skills should be extremely productive.
INFORMATION: Presents interesting facts about the
purchased product.
QR CODE: Presents additional information or links
with more details about the presented text.
05
Torniquete
Tx1500
2. Orientations
Read the information and instructions of this manual carefully, before using the
product. This ensures the correct use of the equipment and maximum use of its
technical features as well as a prolonged service life.
Keep this manual for future consultations.
Digicon reserves its right to alter its products at any moment to adapt them to more
recent technical advancements.
Digicon maintains its right to alter the information contained in this manual without
previous notice.
Digicon does not provide any contractual warranty concerning the information in
this manual, and cannot be held responsible for errors it may contain and problems
due to its use.
The information contained in this manual is exclusive property of Digicon and is
protected by copyright laws.
This manual cannot be reproduced, photocopied or translated, in its entirety or in
part, into any kind of medium, without Digicon's written consent.
3. Introduction
The Full-height is a bidirectional access control equipment forTurnstile Tx1500
entrance and exit of pedestrians. Highly resistant, both indoors and outdoors, it is
sturdy, safe, and firmly fixated to the floor. It is completely integrated to access
controllers. This manual presents a detailed description the installation of Tx1500
and of the components that accompany it.
To see our complete catalogue, visit www.digicon.com.br.
Torniquete
Tx1500
06
4.Installing Tx1500
1 Prepare the Turnstile assembly
th tep:S
The floor where the turnstile will be fixed must meet the following specifications:
a. 1,6mm x l 1,4mm xDimensions: Direction of flow columns width concrete
height 10 cm;
b. ;Necessary height: 2. meters5
c. ;Level the floor for better product performance
d. ;Floor specification (FCK15 M.P.A. concrete or equivalent)
e. 1,6m x 1,4m x 2,6m.Floor specification (FCK15 M.P.A. concrete or equivalent)
Power point input and network cable can be on the floor, preferably at point 3 or
overhead pipes.
Obs.:The dimensions of the concrete block and power inputs are only a suggestion.
The client can choose smaller bases (footing) at the fixing points (determined by
template).
List of tools for assembling the Turnstile:
INFORMATION: Illustrative image (measures specified in “mm”).
Duct
Point 4
Reference point
Point 1
Point 3
Point 2
725
628 628
362 725
Torniquete
Tx1500
07
1 socket wrench with
socket of 14 and
17mm;
1 combination wrench
17;
1 socket wrench 10
with extension;
1 ;n.3 Allen wrench
1 n. 5 Allen wrench;
1medium-sized
Philips screwdriver;
1 medium-sized
screwdriver;
1 hard plastic
hammer
1 plum-line or water
level;
1 silicone tube;
Molykote BR2 Plus
graphite grease;
Step ladder with four
steps;
Electric drill and drill
bits for concrete with
6 and 14 cm;
Bolter – 10 parts for
every product.
2th tep:S Drilling device
a. It will be necessary to add cardboard or bubble wrap under the device so not to
damage the roof painting when using the drilling demarcations;
b. Screw the device (P1) to the turnstile's roof (P1);
c. Position the assembled parts in the area chosen for installation, observing the flow
of entrance and exit;
d. Observe the desired side for the opening (lock side) of the central support for
maintenance;
e. P ;lace the roof (P1) and fix tem with screw (P2) and nut (P3)
f. The pre-hole must be done with an Ø6mm drill, so there are no damages to the
device's holes;
g. Remove the device and drill again all the holes with an Ø14mm drill.
Quantity of parts used in this stage:
P1 =1xRoof
P2 = 1x Drilling device
P3 = 2x M6x15Allen screw
P4 = 2x M6Nut
Obs.: After all demarcations, disassemble the device to use the part later (P1).
90°
P1
P3 - P4
P2
Torniquete
Tx1500
ATTENTION: The place of installation and the direction of entrance
.and exit must be defined alongside the responsible for the place
08
3th Step: Assembly of sides with rods or glass sides
Sides with rods:
a. Fit the sides (P5) and (P6) so to form an arch;
b. Screw the sides using washer (P7) and screw (P8); repeat on the four fixing
points (two on the upper part, two on the lower part);
c. Place the screw (P26) with washers (P7) on both sides and on the nuts (P18) to
finish the holes on the arch's upper part.
Quantity of parts used in this stage:
P5 = 1x - 5 side rods
P6 = 1x- 4 side rods
P7 = 8x - D=30,5 x 10,5 x 3mmWasher
P8 = 4x - M10 x 20Hexagon head screw
P18 = 2x - M10Nut
P26 = 2x - M10 x 30Hexagon head screw
This assembly will result in the set (P23) – Assembling the arch's sides
P5
P18
P26
P8
P7
P6
Torniquete
Tx1500
09
Glass sides:
a. Fit the sides (P39) and (P40) so to form an arch;
b. Screw the sides using washer (P41) and screw (P8); repeat on the four fixing
points (two on the upper part, two on the lower part);
c. Fix the glass support (P42) to the rods' inner parts using washers (P25) 2x and
screws (P20) 2x in each support;
d. Fit the nut for the glass support (P45) to the glass support (P42); after the
nut was placed on the other side, place the two PVC washers (P44);
e. Repeat items “c” and “d” 16 times in each support fixation.
Quantity of parts used in this stage:
P8 = 4x - Hexagon head screws M10 x 20
P20 = 32x - M4 x 12cross head screw
P25 = 32x - D4flat washer
P39 = 1x - 2 side rods
P40 = 1x - 1 side rod
P41 = 4x - flat washer D10
P42 = 16x - glass support
P44 = 32x - PVC washer
P45 = 16x - glass support nut
This assembly will result in the set (P48) – Assembly of glass sides.
Torniquete
Tx1500
10
P39
P45
P41
P25
P20
P42
P44
P8
P40
Table des matières
