Digi-tech RP500 Instructions d'installation et d'utilisation

Looper

Addendum

Multi Effects

Switching System

Updating your RP500

To update your RP500 with the version 2.0 firmware, follow these steps:

1.Connect your RP500’s USB cable to an available USB port on your computer

and power the RP500.

2. Backup your RP500 using X-Edit.

ATTENTION: ALL PRESETS WILL BE ERASED DURING THE

UPDATE PROCESS. BE SURETO BACKUP THE RP500 FIRST

USING X-EDIT BEFORE UPDATING!!

3.Visit www.digitech.com/software_support/ using your web browser.

4. Select RP500 from the Select Product menu and then select the operating

system for your computer from the Select Operating System menu.

5.Click the 1. Download Files tab and download the NetUpdater application

to your desktop.

6.Launch the NetUpdater application and follow the onscreen instructions to

update your RP500 to version 2.0.

7. Use X-Edit to restore the backup you made to the RP500.

Once your RP500 is successfully updated, you can now begin using the new

Looper feature.

Using the RP500’s Looper

The RP500 now includes a dedicated Looper phrase sampler that lets you

record up to 20 seconds of your guitar playing and play it back as an endless

loop so you can solo over it. Once a loop is recorded, you can also add more

guitar parts to the recorded loop (overdub). What’s great about the RP500’s

Looper is that even while the Looper is playing back and/or recording you can

still select different presets or turn on and off effects to add different sounds

to your loop or overdubs. When the Looper is turned on, the Up/Down

footswitches will not select preset banks (Preset Mode) or select presets

(Pedalboard Mode). You can use the 1-5 footswitches to do this.

There are two ways to use the Looper: with a “quiet start” or “on the fly.”

“Quiet start” means you “Arm” the Looper’s record feature when you’re not

playing your guitar, and then it automatically starts recording when you start

playing.“On the fly” means you arm the record feature while you’re playing,

and the Looper starts recording as soon as you step on the Down footswitch.

To use the Looper with a quiet start, follow these steps:

1.Press and hold the Up Footswitch for 2 seconds until LOOPER appears in

the display indicating the Looper is now active.

2.To begin looping, press the Down Footswitch. The Display will show

ARMED indicating the Looper is armed and ready to record but not actually

recording yet.

3.Begin playing a phrase on the guitar.The the Display will show RECRDING

and the Looper will begin recording anything that is played.

4.Once you are ready to set the loop point, press Down Footswitch again.

The Display will read PLAYING and the recorded phrase will now begin

playing back.

5.To add an overdub to the looped phrase, press the Down Footswitch

again. The display will read OVERDUB and anything that is played at this time

will be added to the loop. When you are ﬁnished with the overdub, press the

Down Footswitch again. The display will read PLAYING and the looped

phrase will continue with the newly added overdub phrase added.

6.To stop the Phrase Looper, press the Up Footswitch and the display

will read STOPPED. You can resume playback by pressing the Down

Footswitch again.

7.To clear a recorded loop, stop the loop playback ﬁrst as outlined in step 6

and then press and hold the Up Footswitch for 2 seconds until the display

read LOOPCLRD.

To use the Looper on the fly, follow these steps:

1.Press and hold the Up Footswitch for 3 seconds until LOOPER appears in

the display indicating the Looper is now active.

2.Start playing your guitar.

3.To begin looping, press the Down Footswitch. The Display will show

RECRDING and the Looper will begin recording anything that is played.

4.Once you are ready to set the loop point, press Down Footswitch again.

The Display will read PLAYING and the recorded phrase will now begin

playing back.

5.To add an overdub to the looped phrase, press the Down Footswitch

again. The display will read OVERDUB and anything that is played at this time

will be added to the loop. When you are ﬁnished with the overdub, press the

Down Footswitch again. The display will read PLAYING and the looped

phrase will continue with the newly added overdub phrase added.

6.To stop the Phrase Looper, press the Up Footswitch and the display

will read STOPPED. You can resume playback by pressing the Down

Footswitch again.

7.To clear a recorded loop, stop the loop playback ﬁrst as outlined in step 6

and then press and hold the Up Footswitch for 2 seconds until the display

read LOOPCLRD.

To exit the Phrase Looper mode, press and hold the Up Footswitch for

4 seconds until the display reads LOOPEXIT. Exiting the Looper clears the

recorded loop.

DigiTech®

8760 South Sandy Parkway

Sandy, Utah 84070

PH (801) 566-8800

FAX (801) 566-7005

http://www.digitech.com

RP500 Looper Addendum

Autres manuels pour RP500

Table des matières

Autres manuels digi-tech Pédale musicale

digi-tech

digi-tech Modeling Guitar Processor and USB Recording Interface... Manuel utilisateur

digi-tech

digi-tech RP300 Manuel utilisateur

digi-tech

digi-tech BP-90 Manuel utilisateur

digi-tech

digi-tech HARDWIRE CR-7 Manuel utilisateur

digi-tech

digi-tech TRIO+ Band Creator+ Looper Manuel utilisateur

digi-tech

digi-tech HOTHEAD Manuel utilisateur

digi-tech

digi-tech GNX3000 Manuel utilisateur

digi-tech

digi-tech JAMMAN - MANUAL 2 Manuel utilisateur

digi-tech

digi-tech GNX3 Manuel utilisateur

digi-tech

digi-tech RP100 Manuel utilisateur

digi-tech

digi-tech PDS2020 Manuel utilisateur

digi-tech

digi-tech GSP 21 Legend Manuel utilisateur

digi-tech

digi-tech RP500 Mise à jour du firmware

digi-tech

digi-tech PDS1700 Manuel utilisateur

digi-tech

digi-tech RP350 Manuel utilisateur

digi-tech

digi-tech Element Manuel utilisateur

digi-tech

digi-tech Element Manuel utilisateur

digi-tech

digi-tech JAMMAN STEREO Manuel utilisateur

digi-tech

digi-tech Ventura Vibe Manuel utilisateur

digi-tech

digi-tech GSP 21 Legend Manuel utilisateur

digi-tech

digi-tech RP14D Manuel utilisateur

digi-tech

digi-tech nautila Manuel utilisateur

digi-tech

digi-tech Distortion Factory DF-7 Manuel utilisateur

digi-tech

digi-tech RPX400 Manuel utilisateur

Manuels Pédale musicale populaires d'autres marques

Behringer

Behringer ULTRA WAH UW300 Manuel utilisateur

Whirlwind

Whirlwind oc-bass Manuel utilisateur

Strymon

Strymon Lex-rotary Manuel utilisateur

Behringer

Behringer PB600 Manuel utilisateur

Lexicon

Lexicon MX200 Manuel utilisateur

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Manuel utilisateur

Matthews Effects

Matthews Effects Whaler V2 Manuel utilisateur

Grid 1

Grid 1 Pedal Jeanie Manuel utilisateur

Amptweaker

Amptweaker tightboost Manuel utilisateur

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Manuel utilisateur

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Manuel utilisateur

BYOC

BYOC Analog Chorus Manuel

Dimavery

Dimavery EPVP-50 Manuel utilisateur

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Manuel utilisateur

Pro-MIDI

Pro-MIDI G25 Manuel utilisateur

DW 7000 Manuel utilisateur

FAMC

FAMC Liquid-Foot Jr. Series Manuel utilisateur

Dimavery

Dimavery EPOD-50 Overdrive Manuel utilisateur

digi-tech RP500 Instructions d'installation et d'utilisation

Manuels Pédale musicale populaires d'autres marques