DIG 410BT Series Manuel utilisateur

INSTRUCTION MANUAL

410BT Series Bluetooth®

Battery Powered Irrigation Controller

410BT-000 | 410BT-075 | 410BT-100 | 410BT-150 | 410BT-200

FCC certied | Bluetooth® certied | Waterproof | 3-year Limited Warranty

1. INTRODUCTION

Thank you for purchasing DIG’s 410BT Single Station Battery Operated

Controller. This manual describes how to get the 410BT series

controller up and running quickly. After reading this manual and

becoming familiar with the basic functionality of the controller, use the

manual as a reference for less common tasks in the future.

2. ABOUT THE 410BT BATTERY OPERATED CONTROLLER

The 410BT series irrigation controller employs the latest in Bluetooth®

technology using the free DIG BTT app for Android™ or iPhone®.

The 410BT is available as a single station battery operated controller

and is powered by two AA batteries that can last up to one year using

name brand alkaline batteries. The controller is enclosed in a compact,

waterproof housing to protect it from degradation.

3. COMPONENT IDENTIFICATION

Two AA batteries

(not included)

One button

for manual

run and reset

Lid

Battery Compartment Cap

Solenoid

4. INSTALLING THE BATTERIES

1. Open the battery compartment cap by turning it counterclockwise.

2. Install two fresh, brand name, AA alkaline batteries (not included)

and note the proper direction of the positive and negative

orientation on the underside of the controller.

3. Insert and screw the battery cap clockwise. Make sure to securely

tighten the cover rmly by hand only. The controller will now appear

on the smartphone app and is ready to be connected to and

programmed.

5. VALVE ADAPTER INSTALLATION

The 410BT series controller includes three adapters to retrot Rainbird,

Hunter and Toro valves. Follow the instructions below to install.

1. Shut off the main water supply

2. Remove the existing solenoid if applicable.

NOTE: If adapting to an IRRITROL valve, remove the solenoid but

leave the existing solenoid adapter installed.

3. Select the appropriate solenoid adapter associated with the valve.

(see chart A)

4. Screw the solenoid adapter into the valve bonnet by hand, tighten

with pliers if necessary – but do not over tighten.

5. Thread the 410BT series solenoid into the valve adapter. Hand

tighten only.

6. Turn the main water supply on and pressurize the valve; the valve

may discharge water momentarily but should then shut off.

7. Test the controller and the installation by pressing the button on

the controller or see pages 11-12 on how to perform a manual run

through the app. To turn the valve on via the solenoid, lift the

410BT series controller from the solenoid and turn the solenoid

counter clockwise 1/2 to 3/4 of a turn, or until you hear or see water

owing through the valve. To turn the water off, turn the solenoid

clockwise 1/2 to 3/4 of a turn and wait a few seconds for the

valve to close.

8. Program the 410BT series controller (see pages 4-12).

6. IN-LINE VALVE INSTALLATION

Rated operating pressure: 10-125 PSI

Recommended Operating Pressure: 10-80 PSI

Warning: Wrap all ttings with Teon tape! Do not use pipe cement on

ttings or the valve as this will damage the valve and void the warranty!

1. Shut off main water supply.

2. Install a 3/4″ball or gate valve onto the PVC pipe or to the valve

manifold before installing the controller (Figure 6a and 6b).

CHART A

Model Compatible Valves

30-920 BERMAD series 200, HIT series 500,DOROT series 80,

GRISWOLD series2000, DW and BUCKNER series VB valves

30-921

INCLUDED

RAIN BIRD DV, DVF, PGA, PEB (1″only),GB, EFB-C P,

BPE, PESB (1″only)and ASVF valves

30-922

INCLUDED

HUNTER series ASV, HPV, ICV,PGV, SRV, IBV and

ASVF valves

30-923 WEATHERMATIC series 12000, 21000, 8200CR valves

30-924

INCLUDED

IRRITROL series 100, 200B, 205, 217B,

700, 2400, 2500, 2600 and TORO series 220, P220 valves

30-925 SUPERIOR series 950, HUNTER HBV and TORO series

252 valves (1.5″and larger)

3. Turn water supply on to ush the line and then shut the water off

using the ball or gate valve.

4. Wrap the male threads of the PVC adapters with 4-6 layers of Teon

tape, then tighten into the valve with a wrench.

5. Glue ttings to PVC main line and allow to dry.

6. Turn water supply on to pressurize the system. The controller will

open momentarily and then will shut off.

7. The unit is now ready to be programmed

7. PROGRAMMING

• Download the DIG BTT app using the iOS App Store, Google Play, or

the QR code on the box.

• Open the DIG BTT app from your smartphone or tablet and use the

instructions in the App Screens Overview to program and operate

the controller.

Figure 6a

Above-ground installation

Below-ground installation

ow

Figure 6b

APP SCREENS OVERVIEW

The DIG BTT app automatically scans for nearby controllers after

installation. Any DIG Bluetooth® controllers within 50′(15 meters) line

of sight will appear on screen.

• Your new controller will appear as the BT Controller. Its

default image, status (watering -on- or not watering -off-),

connection strength, and battery life will appear alongside it.

• Tap on the controller to connect to it and start programming.

You can access Connection History and Contact Us through the

information icon in the top right corner of the screen.

• The Connection History allows you to see every controller and

timer connected to from this phone or tablet. It stores the data

it last received from each tap timer, but no editing can be done.

Deleting an entry will remove all the saved data for that unit. Any

passwords and/or pictures need to be reentered. To delete an entry,

tap it and select the trash icon.

Information icon

Default image

Controller name

Last run

information

Battery life

Connection

strength

Indicates if

controller is

currently

runnning

or not

HOME SCREEN

Once connected, the Home screen will appear. This screen has

everything needed to program the controller.

By default, the controller’s Program is off. To turn it on, push the switch

under the “Program” area. It will turn green and the Program area will

light up indicating that the program is active and can now be modied.

The controller is now ready to be programmed. Simply select the

schedule (weekly, even/odd, or cyclical), set your start date or days, add

times, and set a duration. The controller is updated immediately each

time a button is tapped.

Schedule

Overview:

Shows a chart

with current

program run

times. Red

lines indicate

that there is

an overlapping

start time

Activate or

deactivate

the program

Program

schedule

Weekly days

settings

Up to ve start

times. Select an

existing start

time to edit/

delete.

Red start times

are overlapping

and will not run

Run time for

valve

Home

(current page)

Controller

settings

Manual run

Picture of

controller

CONTROLLER SETTINGS

The controller’s Settings screen contains everything else needed to

fully control your irrigation system. It can be reached by selecting the

Controller Settings button on the bottom of the screen. On this

screen you can turn on or off the entire system through the System

Active switch, add a rain delay to shut off the controller for a limited

time, budget each month to modify the watering duration based on the

season, set specic dates on which the timer should not run, and view

12-month history of the controller.

Use the settings menu to rename the controller to something

memorable and upload a picture for easy and fast recognition for future

viewing. Set a password to prevent unallowed users from connecting to

your timer. The password is saved to the phone so it will (almost) never

have to be entered again (unless it’s changed or when connecting to the

timer with a new phone).

Autres manuels pour 410BT Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DIG Système d'irrigation

DIG

DIG 400A Series Manuel utilisateur

DIG

DIG GE2050 Manuel utilisateur

DIG

DIG ECO1 MVA Manuel utilisateur

DIG

DIG 8855-1GB Manuel utilisateur

DIG

DIG 5004-I Four Station Manuel utilisateur

DIG

DIG 12 Outlet Drip Manifold Manuel utilisateur

DIG

DIG GRWKIT-12 Manuel utilisateur

DIG

DIG LEIT X Series Manuel utilisateur

DIG

DIG 5006-IP Manuel utilisateur

DIG

DIG FM01AS Manuel utilisateur

Manuels Système d'irrigation populaires d'autres marques

Hunter

Hunter Institutional Series Manuel utilisateur

Cellfast

Cellfast 52-305 Manuel utilisateur

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Manuel utilisateur

Tyco Fire Product

Tyco Fire Product CENTRAL A Manuel utilisateur

Oral Care Technologies

Oral Care Technologies Hydro Floss Manuel utilisateur

Reliable

Reliable F1-300 Manuel utilisateur

Tyco Fire Product

Tyco Fire Product Gem F892 Manuel utilisateur

Netafim

Netafim NETBEAT Manuel utilisateur

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Manuel utilisateur

Tyco

Tyco CC3 Manuel utilisateur

Reliable

Reliable F4FR Manuel utilisateur

OpenSprinkler

OpenSprinkler OSPi Manuel utilisateur

EINHELL

EINHELL GE-WW 5537 E Manuel utilisateur

Valley

Valley Bender160 Manuel utilisateur

Reliable

Reliable F1FR42 Series Manuel utilisateur

Reliable

Reliable F1FR-300 Manuel utilisateur

Toro

Toro 730 Series Guide rapide

Eden

Eden 97063-EDAMZ Manuel utilisateur