DIAMOND MOTION MEMO2GO Manuel utilisateur

MEMO2GO Handling Instructions Level 1 V 1.5 13-04-2018 1

MEMO2GO Handling Instructions Level 1

The following steps are recommended to achieve an effective and trouble-free installation and operation of your

MEMO2GO system:

Prepare a consignment (in the Carpenter Workshop)

- Take required items from inventory

- Connect items as shown above

- Program SPECIAL CHIP CARDS on all controllers of this

consignment. Refer to page 4 of this manual

- Program ACCESS CHIP CARDS and ACCESS KEY FOBS

on all controllers of this consignment. Refer to page 5

of this manual

- Change CONTROLLER SETTINGS on all controllers of this

consigment (if necessary). Refer to page 6 and 7 of this

manual - otherwise use factory settings

Power Supply

Controller

Antenna

MEMO2GO Handling Instructions Level 1 V 1.5 13-04-2018 2

Install the Items

- Follow the INSTALLATION GUIDELINES carefully. If you

don’t have the guidelines for Antennas, Controllers, Locks

etc. please request them from MEMO

- Take care that the controllers are accessible for

maintenance

- Take care that the antennas have a good reading range

to the front side

A. Check that the lock can’t be manipulated from the outside.

B. Take care that the Locks are catching the door safe, re-lock

correct if door was not opened

FRONT PANEL OR DOOR

Antenna-Space Milled down

to 5mm (max. 10mm)

How can we help?

MEMO2GO Handling Instructions Level 1 V 1.5 13-04-2018 3

Handover to Shop Managers

- Mark the MASTER CARDS of each Controller

with the FURNITURE NAME/NUMBER

- Hand over ALL MASTER CARDS of ALL Controllers to Shop Managers

- Hand over ALL SPECIAL CHIP CARDS and ACCESS CHIP CARDS / KEY

FOBS to Shop Managers

- Handover the MEMO2GO Handling Instructions to the

Shop Managers

- Make the Shop Managers aware that the MASTER

CARDS are required to PROGRAM NEW and ERASE

LOST CHIP CARDS / KEY FOBS

! IMPORTANT !

LOSING a MASTER CARD leads to INCAPABILITY of programming new CARDS and KEY FOBS

once the ERASE CARD is used!

SPECIAL

CARDS

CHIP

KEYS

MEMO2GO Handling Instructions Level 1 V 1.5 13-04-2018 4

Special Function Cards Programming

Power Supply

Master Card

Programming Card

Erasing Card

Decoration Card

Antenna

Supervisor Card

within 10 sec.

Short Beep

Double Short Beep

Long Beep

Triple Short Beep

Quadruple Short Beep

Tri-Tone Beep

Present the Master

Card twice at the

Antenna

Present the

Programming Card

at the Antenna

Present the Erasing

Card at the

Antenna

Present the

Decoration Card at

the Antenna

Ready for

Normal

Operation

Present the

Supervisor Card at

the Antenna

- Connect the above items

- Prepare the above CHIP Keys

Between steps 2 and 5 if the Card is not presented within 10 seconds and the next Beep-tone sounds, it is

too late. The programming on the particular card will be skipped

Controller

MEMO2GO Handling Instructions Level 1 V 1.5 13-04-2018 5

Programming Keys

Erasing Keys

within 3 sec.

3 sec. per key

within 3 sec.

Double Short Beep

Double Short

Beep

Tri-Tone Beep

Present the

Programming Card

at the Antenna

Present the First

Key Fob at the

Antenna

Present the Second

Key Fob at the

Antenna

Present the Last

Key Fob at the

Antenna

Ready for

Normal

Operation

Continue with

subsequent keys

Tri-Tone Beep

Long Beep

Present the Erasing

Card at the Antenna

Ready for Normal

Operation

All Access Keys

Decoration Card

Supervisor Card

are Erased

MEMO2GO Handling Instructions Level 1 V 1.5 13-04-2018 6

Controller Configuration

Controller Configuration with Code

Power Supply

12-Button Hand Terminal

Prepare the following items:

•Ready and powered system

consisting of Controller,

Antenna and Power Supply

•Master Card

•12-Button Hand Terminal

Connected to the Controller

Antenna

Press

Short Beep

Long Beep

Press

Present the Master

Card at the Antenna

Press

Ready for Normal

Operation

Example Configuration with 12-Button Hand Terminal

Type Code: E 2 1 E 1 0 E

To change configuration: Lock Activation 10 seconds

Master Card

Controller

MEMO2GO Handling Instructions Level 1 V 1.5 13-04-2018 7

FUNCTION

FACTORY SETTING

CODE

Factory Settings

E250EE

Door Open Time (0 - 120 seconds)

30 seconds

E132E030E

Lock Activation Duration (1 - 250 seconds)

5 seconds

E21E005E

Lock Opening Delay (0 - 250 seconds)

0 seconds

E41E000E

Intrusion Alarm ON

E120E1E

Intrusion Alarm OFF

E120E0E

Silent Alarm ON

OFF

E122E1E

Silent Alarm OFF

E122E0E

Door Open Retrigger ON

E137E1E

Door Open Retrigger OFF

E137E0E

One Door Only Mode ON

E138E1E

One Door Only Mode OFF

OFF

E138E0E

Key Opening Mode ON

E81E1E

Key Opening Mode OFF

OFF

E81E0E

Separated Antennas ON *

E202E1E

Separated Antennas OFF *

OFF

E202E0E

* if applicable

Controller Configuration

List of Feature Settings

Table des matières

Autres manuels DIAMOND MOTION Matériel réseau

DIAMOND MOTION

DIAMOND MOTION MEMO2GO Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur