DFI KS070-FS Manuel utilisateur

KS070-FS Installation Guide

Top Panel I/O Ports

SD COM

Bottom Panel I/O Ports

Power Switch

Line-out/Mic-in

USB 2.0

DC-in

HDMI

COM

(RS232/422/485)

8-bit DIO Mini USB LAN

DFI reserves the right to change the specifications at any time prior

to the product's release. This QIG is based on versions that may not

resemble your actual products. For the latest revision and details of the

installation process, please refer to related technical docs on our website

at http://go.d.com/KS070-FS.

Connecting the Cable to the Terminal Block

The system's power connector is a two-pole terminal block. Please insert the corresponding

end ("+" or "-") of a power adaptor to the respective pole of the terminal block.

1. Insert the cable end of the power adaptor to the terminal block. To rmly x the cable

into the terminal block, use a screwdriver to clamp down the wires to the screw that is in

the terminal block.

Terminal block

Wire

Power adapter cable

2. Plug the terminal block into the DC-in connector and then tighten the screws to secure the

terminal block in place.

DC-in

connector

Screws

White Wire Black Wire

+ -

Removing the Chassis Cover

Before working inside the system, make sure the system has been powered off and disconnect

all power cords and cables.

The 8 mounting screws on the sides and bottom of the system are used to secure the cover to

the chassis. Remove these screws and the COM port screws.

Installing a Mini PCIe and SIM Card

The system board is equipped with 2 Mini PCIe slots.

One Mini PCIe slot (with SIM card slot) provides both

USB and PCIe interfaces whereas the other Mini PCIe

slot provides only mSATA interface.

Note: Be sure to place the card with the IC facing down

and the angled corner aligning with the socket's angled

corner so it will be correctly in contact with the system

board.

Mounting Screw (COM port)

Mounting Screw

Mini PCIe Slot

SIM card socket

The microSD card slot is located on the Qseven module internally. You may need to remove

the Qseven module rst to access the card slot. Then insert the card straight into the socket.

Qseven module

microSD card

Mounting screw

Speaker

Before inserting a SIM card into the socket, you have

to remove mounting screws on the speaker.

Insert the

SIM card into the SIM card socket, and push it to take

the card out of the socket.

Installing the microSD Card

mSATA Slot

Board Layout and Jumper Settings

LCD Panel Power Select JP2

+12V 1-2 On

+5V Standby 3-4 On

+3V Standby (default) 5-6 On

COM 1 /COM 2

RS232/422/485 Select

JP4 (for COM 1), JP6 (for COM 2)

RS232 (default) 1-2 On

RS422 3-4 On

RS485 5-6 On

Touch Panel Power Select JP3

+5V Standby 1-2 On

+3V Standby (default) 2-3 On

Dimming Mode Select JP10

PWM Mode (default) 1-2 On

Voltage Mode 2-3 On

Dimming Mode Select JP5

+12V 1-2 On

+5V Standby (default) 3-4 On

+3V Standby 5-6 On

LCD/Inverter Power Select JP5

+12V 1-2 On

+5V Standby (default) 3-4 On

+3V Standby 5-6 On

Download Mode Select JP9

Serial Download Mode 1-2 On

Normal Boot (default) 2-3 On

Line-out/Mic-in Select JP7 (for Line-out), JP8 (for Mic-in)

Line-out (JP7) 1-2, 3-4, 5-6 On

Mic-in (JP8) 1-2, 3-4, 5-6 On

Boot Device Select Switch

eMMC 1 Off, 2 Off, 3 On, 4 On

uSD 1 Off, 2 Off, 3 On, 4 Off

SPI3 on board SPI 1 On, 2 On, 3 Off, 4 On

SPI1 on carrier board 1 On, 2 Off, 3 Off, 4 On

933-KS0702-000G

DVT

A55701930

Aug 20, 2019

LVDS LCD Panel

COM

DC-in

12-36V

LAN

USB 0-1

HDMI

SIM

COM 2

Mini PCIe

Mini PCIe (mSATA)

ITE

IT8518E

USB 2.0

SD LED

Mic-in/

Line-out

MXM

14 2

Digital I/O

Download Mode

Select (JP9)

Mic-in/Line-out

Select (JP8)

COM 1 RS232/422/485

Select (JP4)

COM 2 RS232/422/485

Select (JP6)

RTC

Battery

AMP_L Mic-in/Line-out

Select (JP7)

(JP2)

Panel Power Select

(JP5)

(JP3)

(JP10)

(JP5)

(JP2)

(JP3)

(JP10)

Dimming Mode Select

Touch Panel Power Select

LCD/Inverter Power Select

CAN-bus

(optional)

COM RS232/UART5 Select

(JP11)/(JP12)

USB Client

COM 1 Power LED

MCS7840CV

Power

Switch

(JP12)

(JP11)

AMP_R

Autres manuels DFI Écran tactile

DFI

DFI TPC121 Guide d'installation

DFI

DFI TPC121 Manuel utilisateur

DFI

DFI VP101-BT Manuel utilisateur

DFI

DFI KS310-IMX6 Manuel utilisateur

DFI

DFI TPC150-SD Instructions d'utilisation et d'entretien

DFI

DFI KS070-AL Manuel utilisateur

DFI

DFI VS436 (15") Manuel utilisateur

DFI

DFI TPC121 Manuel utilisateur

DFI

DFI PPC Workstation 19 480 Manuel utilisateur

DFI

DFI TPC150 Guide d'installation

DFI

DFI KS230 Manuel utilisateur

DFI

DFI VP070-M8M Manuel utilisateur

DFI

DFI KS150-BT Manuel utilisateur

DFI

DFI KS210-IMX6 Manuel utilisateur

DFI

DFI KS070-BT Manuel utilisateur

DFI

DFI TPC150-SD Manuel utilisateur

DFI

DFI KS150-BT Manuel utilisateur

DFI

DFI KS156-AL Manuel utilisateur

DFI

DFI KS070-BT Manuel utilisateur

DFI

DFI TPC121 Manuel utilisateur

DFI

DFI KSM-KH Series Manuel utilisateur

DFI

DFI VP070-M8M Manuel utilisateur

DFI

DFI KS057R-FS Manuel utilisateur

DFI

DFI KS101-BT Manuel utilisateur

Manuels Écran tactile populaires d'autres marques

FlowLine

FlowLine Data loop Manuel utilisateur

ALPEX

ALPEX AEx-8 P Series Manuel utilisateur

Ltech

Ltech E5S Manuel utilisateur

Harman

Harman AMX MODERO S MSD-701-L2 Manuel utilisateur

Acnodes

Acnodes PC 1150 Manuel utilisateur

AIS

AIS IP10IA99 series Manuel utilisateur

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuel utilisateur

YASKAWA

YASKAWA TP 610C Manuel utilisateur

B&R

B&R Power Panel C Series Manuel utilisateur

Beijer Electronics

Beijer Electronics X2 control Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT321W-521 Manuel utilisateur

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuel utilisateur

Qomo

Qomo QIT1386 Manuel utilisateur

AMX

AMX AXP-PPC Mode d’emploi

Sartorius

Sartorius X3 PR 5410 Manuel utilisateur

AMX

AMX Modero X Series Manuel utilisateur

Advantech

Advantech TPC-30 Series Manuel utilisateur

B&R Industries

B&R Industries MAPPC900-ENG Manuel utilisateur