DeWalt Vertikut Manuel utilisateur

Attaching your DeWalt deep cut band saw to the Vertikut stand

1. Unplug the saw and remove the blade.

2. Remove the cutting guide from your saw by removing the two flathead screws

that hold it on.

3. Take the assembled stand and find the two counterbored holes in the table top.

The tabletop goes on to the saw in place of the cutting guide you just removed.

4. Line up the holes on the tabletop with the nuts in the saw and thread in the

flatheads on at a time.

5. Re-install the blade making sure to slide it into the slot in the tabletop as you put it

into position on the saw.

WARNING!!!!

Read and understand the entire contents of this

sheet before attempting set-up or operation of this equipment

•This product is designed and intended for use by properly trained and experienced personnel only.

If you are not familiar with the proper safe use of hand band saws, DO NOT USE THIS PRODUCT

UNTIL PROPER TRAINING AND KNOWLEDGE HAS BEEN OBTAINED.

•Reduce the risk of unintentional starting. Make sure switch is in the OFF position before plugging in

the saw.

•Use the right blade. Do not force a blade to cut a material for which it was not designed.

•Maintain tools with care. Keep blade sharp and clean for best and safest performance. Follow saw

manufacturers instructions for changing blades.

•Always disconnect the saw from the power source before adjusting, servicing or changing blades.

•Check for damaged parts. Check for alignment of moving parts, breakage of parts, mounting, and any

other condition that may affect the tools operation. Any part that is damaged should be repaired or

replaced.

•Turn power off. Never leave a saw unattended. Do not leave saw until it comes to a complete stop.

•Keep work area clean. Cluttered areas and benches invite accidents.

•Do not use in a dangerous environment. Do not use power tools in damp or wet locations, or expose

them to rain. Keep work area well lighted.

•Keep children and visitors away. All visitors should be kept a safe distance from the work area.

•Make the workshop child proof. Use padlocks, master switches, remove starter keys or unplug all

tools.

•Wear proper apparel. Loose clothing, gloves, neckties, rings, bracelets, or other jewelry may get

caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain

long hair.

•Always use safety glasses. Every day glasses only have impact resistance lenses; they are not safety

glasses.

•Do not overreach. Keep proper footing and balance at all times.

•Do not place hands near the blade while cutting.

•Read and understand all warnings provided by saw manufacturer.

•Failure to comply with all of these warnings may result in serious injury.

April 29, 2008

Table des matières

Autres manuels DeWalt Support et étagère

DeWalt

DeWalt DW7451 Manuel utilisateur

DeWalt

DeWalt DW723 Manuel utilisateur

DeWalt

DeWalt DWST82800 Manuel utilisateur

DeWalt

DeWalt DE7035 Manuel utilisateur

DeWalt

DeWalt DCAVR332 Manuel utilisateur

DeWalt

DeWalt DXST4500PBK Manuel utilisateur

DeWalt

DeWalt DWX723-XE Manuel utilisateur

DeWalt

DeWalt DW7350 Manuel utilisateur

DeWalt

DeWalt D24001 Manuel utilisateur

DeWalt

DeWalt DWE74911 Manuel utilisateur

DeWalt

DeWalt DWX725 Manuel utilisateur

DeWalt

DeWalt DWE74911 Manuel utilisateur

DeWalt

DeWalt DXST10000 Manuel utilisateur

DeWalt

DeWalt DWE74911 Manuel utilisateur

DeWalt

DeWalt DE7450 Manuel utilisateur

DeWalt

DeWalt DE7035 Manuel utilisateur

DeWalt

DeWalt DXST10000 Manuel utilisateur

DeWalt

DeWalt DXST10000EXT Manuel utilisateur

DeWalt

DeWalt DXST10000PBK Manuel utilisateur

DeWalt

DeWalt DE6501 Manuel utilisateur

DeWalt

DeWalt DW7451 Manuel utilisateur

DeWalt

DeWalt DE7260 Manuel utilisateur

DeWalt

DeWalt DXST4500DK Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur