OSD Menu Operation
A. OSD menu flow chart
The function indicated with * for default setting.
B. Tact Switch Operation
This camera utilizes a user menu “ Set Up Menu “ that is displayed on the
monitor. To set items on the “ Set Up Menu “, use the following buttons on
the side panel.
UP Key: This button is used to move the cursor upwards.
Down Key: This button is used to move the cursor downwards.
Right Key: This button is used to move the cursor to the right.
Use this button to select or adjust the parameters of the selected item.
The parameter changes each time this button is pressed.
Left Key: This button is used to move the cursor to the left.
Use this button to select or adjust the parameters of the selected item.
The parameter changes each time this button is pressed.
Set Key: This button is used to set the determined parameter. If the item
has its own setting menu ( indicted by ), press this button to display the
next page setting menu.
C. Opening the Set Up Menu
Press SET Key for three second. The
“ SET UP MENU “ will appear on the
monitor as shown on right side. Check
the current settings on the menu.
Refer to the sections below for a
detailed description of menu items. If
you decide not to make any changes
after checking the current settings,
move the cursor to “ QUIT“ and press
SET Key to close the “ SET UP MENU
“ and return to normal camera picture.
D. Reset
Reset allows you to reset all setup menu items to the factory settings if you are
unsure about the correct settings. Proceed as follows: Move OSD cursor to
“ Reset “ and press SET Key. The words “ Resetting “ momentarily appear on
the monitor. At this time all adjustments and parameters are reset to the
factory default settings.
Note:
If no button is pressed for 30 second while the OSD menu or any other setting
menu is displayed, the menu is automatically canceled and returns to the normal
camera picture.
4
FUNCTION OPERATION
1. Synchronization Setting (SYNC)
You can select internal sync mode (INT) or line-lock mode (LL).
a. Use UP Key and Down Key move the cursor to the Sync parameter and use
Right Key or Left Key to select line-lock ( LL ) or internal ( INT ), and press
SET Key.
b.If LL is selected, the Sync second menu appears, If INT is selected, the
synchronization mode is automatically set to internal sync , and the menu is
displayed INT.
1-1. Line-lock Sync Mode (LL)
The line-lock mode has its own menu for line-lock vertical phase adjustment.
When the vertical phase adjustment menu appears on the monitor. use Right
Key or Lift Key to move the cursor for phase adjustments. If the camera
installation is relocated, check the vertical phase adjustment again since the AC
line phase may be different.
Note: The line-lock ( LL) sync mode is not available when the camera operates
on DC power.
How to make sure the Phase:
Set the oscilloscope to the vertical rate and expand the vertical sync portion on
the oscilloscope.
Press Right Key or Lift Key of the camera to match the vertical phase for both
video output signals as closely as possible.
Phase adjustment range can be incremented in 16 steps by 22.5 degrees.
When Right Key or Lift Key is kept pressed for a second or longer, the " I "
cursor moves faster.
Note : If the AC line contains noise (spike noise, etc.), the stability of
the vertical phase of the camera video output signal may be disturbed.
2. Shutter Speed Setting (Shutter)
To select electronic shutter speed, you can select an manual electronic shutter
speed of 1/50 (1/60), 1/120 (1/100). 1/250. 1/500, 1/1000, 1/2000, 1/4000,
1/10000 seconds. Or Auto Electronics Shutter ( AES ). The 1/50 (1/60) is shutter
OFF. This function is effective to raise the sensitivity in low light conditions when
OFF is selected for Auto IRIS Lens. Move the cursor to the Shutter parameter
and select the electronic shutter speed. The preset values for Shutter (electronic
shutter speed) change by pressing Right Key or Lift Key as follows:
3. Lens
3-1 Bright
This item is used to adjust the level of auto iris tens drive which supplied to DC
drive lens or video iris lens. Before operation make sure that connection is
correct for video auto iris lens or DC auto iris lens.
a. Move the cursor to the Lens parameter and press SET Key, the second
menu of Lens is appear on the monitor.
b. Change the curser by Right Key or left Key to adjust IRIS to close or open.
Once the picture is optimum move curse to Back and press SET key to safe
setting and return to top menu.
3.2 BF
This function is allow installer very easy to adjust optical back focus. When used
auto iris lens, this function will automatically fully open the IRIS of lens and change
to AES ( auto electronics shutter ). In case of manual lens, this function will
automatically switch to AES.
a. Move curse to Lens by Control Key, change to BF and press SET key. In
the meantime “ Press SET for return” is display on monitor.
b. Adjust optical back focus to optimum position that press SET key for return to
top menu. ( Please refer to section H Focus and Back Focal Adjustment )
4. BLC
This provide camera incase face strong light to have compensation luminance on
monitor. There are six BLC pattern and each are could adjust compensation level.
Compensation area indicated as below
5. Configure
5-1. Aperture, Move the curse to Aperture and press SET key. The second menu
will appear. Move the “ I “ to adjust V-Aperture and H-Aperture level.
5-2. Gamma, Move the curse to Gamma and press SET key. The second menu will
appear. Use Lift and Right key to select gamma 0.45, 0.8 or 1.
5-3. Pedestal, Move the curse to Pedestal and press SET key. The second menu
will appear. Move the “ I “ to adjust pedestal level.
5-4. Chroma, Move the curse to Chroma and press SET key. The second menu
will appear. Move the “ I “ to adjust Chroma level.
5-8. AGC, 7 limited value could select to limit enhance gain of AGC circuit, also select
OFF could closed AGC function and select Sens Up to have maximum value (38dB) of
AGC gain.
6. White Balance
6-1. WB-Auto ( White Balance Auto), In this mode, the color temperature is
monitored continuously and thereby white balance is set automatically. The color
temperature range for the proper white balance is approximately 2500 - 9100K.
6-2. WB-Menu (White Balance Menu), This mode provide user to adjust
white balance by manual adjust, There are R-gain and B-gain could adjust
independent.
6-3. WB-Push, Move curse to WB-Push. Press on SET key to start the white
balance tracing. When the white balance setting is completed, release SET key and
push white was completely.
7. CAM Title
The camera provide text generation on the display monitor. The 16 character in one
line is available for CAM Title function.
5
8. D/N
This function provide camera automatically switch from color camera to B/W
camera by auto detect luminance, manual switch or external contact terminal by
IR lamp on rear panel.
8-1. Fuzzy, The camera switch to B/W camera by auto detect luminance.
D/N Level, the detect level could be select by Low or High.
Burst On, Keep Burst signal when camera changes to B/W mode.
Burst Off, Remove Burst signal when camera changes to B/W mode.
8-2. IR Pass, Change camera to B/W camera by selects this function.
Burst On, Keep Burst signal when camera changes to B/W mode.
Burst Off, Remove Burst signal when camera changes to B/W mode.
8-3. IR Cut, Close Day/Night function, keep camera on color mode, at this
mode the camera will not accept IR luminance.
9. RS485
Before operation is function make sure correct connection on rear panel for
RS485.
Provide 000 ~ 999 ID address, 3 Password to protect RS485 setting.
Use arrow key to move curse to RS485 and press SET key,
Password, Before into RS485 setting. Camera system request 3 character
password, input correct password to second menu.
Note, before password change the default password is 000.
Address, provide 000 ~ 999 ID address. Wrong address ID setting both
control and receive will cause remote control no function.
B-rate, Baud rate setting, provide 2 rate select 4800 or 9600.
Note, Incorrect baud rate setting will cause remote control no function.
Package
Camera 1pcs.
InstructionManual 1pcs.
CCDProtectCover 1pcs.
Main Power Cable ( Main power model only ) 1pcs
Specification
General PAL Model / NTSC Model
Image Size 1/3 Format Interline CCD Sensor
Pixel Element PAL Model : 768 (H) ×582 (V) approx. 440K pixels
NTSC Model : 768(H) x 494 (V) approx. 380K pixels
Scanning Frequency PAL 2 : 1 Interlace / H : 15625Hz , V : 50Hz
NTSC 2: 1Interlance / H : 15750Hz, V : 60Hz
Operation Temperature -10℃~ +50℃
Storage Temperature -20℃~ +60℃
Output Terminal BNC 75Ohm Unbalance
Power Source Dual Switching Mode Power Supply DC12V / AC24V ±20%
Universal Switching Power Supply AC100V ~ AC240V
Power Consumption 4.5 W Max,
Power Indicator 3θGreen LED on Rear Panel
IRIS Connector 4 pin Connector For DC Drive Lens ( Panasonic Standard )
3pin Terminal Block For Video Drive Lens
Lens Mount CS Mount, Change C Mount by Adaptor.
Mounting Hole 1/4” Top and Bottom
External Dimension 73mm (W) x 63mm (H) x 122mm (D)
Weight TBD
Functional Specification
Auto IRIS Control Video Drive / DC Drive Separate Output
* Day & Night Optical Low Pass Filter Removable
* IR Lamp Trigger External Relay Contact for GND Loop
Chroma Separate CS / Color Killer
* Color Killer ON / OFF / Fuzzy
SYNC System INT / Line Lock
Line Lock Phase Adjust Range 0°~ 270°
Frequency Range PAL 50Hz ±1Hz / NTSC : 60Hz ±1Hz
Remote Controller RS-485 two way communications
Camera Addressable 001 ~ 999
Text Display 16 Character with one line
Resolution 470 TV Line
Minimum Illumination 0.5Lux @F=1.2 ( 50IRE Video Output )
Video Output 1.0Vpp 75Ohm BNC unbalance
S/N Ratio 50dB
Gamma Compensation 3 Curve Selectable ; 0.45 / 0.8 / 1
Function Control or Selectable By OSD and RS-485
SYNC System INT / LL Selectable
V-Phase 0°~ 270°
Exposure Control Auto Electronics Shutter / Manual Electronics Shutter
/ Auto IRIS lens
Auto Electronics Shutter Max, Limit and Level Adjustable
Menu Electronics Shutter 8 Step 1/50 (1/60), 1/120 (1/100) , 1/250 , 1/500
1/1000 , 1/2000 , 1/4000 , 1/10000
Auto IRIS Lens Driver Video IRIS lens / DC IRIS lens
Lens Level Control Both For DC IRIS Lens and Video IRIS Lens
BLC 6 Area Select and Level Adjustable; Center 1, Center 2,
Door Way 1, Door Way 2, Upper Half, Lower Half.
White Balance Control Auto White Balance / Push White Balance /
Menu White Balance
Auto White Balance 2 Application Range Selectable;
2500K ~ 9500K / 2000K ~ 18000K
Menu White Balance 1 Preset; R gain / B gain Adjustable
Gain Control Auto Gain Control
Auto Gain Control 12dB ~ Sensitivity up (38dB max.) Adjustable.
Gamma Control 3 Step Selectable; 0.45 / 0.8 / 1
Aperture Control 0 ~ 15 IRE Max. For Vertical and Horizontal
Chroma Level Adjustable
* Color Killer ON / OFF / Fuzzy Selectable
* Day/Night IR Pass / IR Cut / Fuzzy
Remote Control RS-485, Two way communications
Address 001 ~ 999 ID selectable
Note : Function indicated * for System Day/Night model only.
Document Nr. : TOM-20030606-01B
Version Nr. : 030804A
Part Nr. : 531-CD000-000
6
Set key
Right key
Down key
Up key
Left key
Detect
Area
CENTER 1 CENTER 2
Detect
Area
DOORWAY 1
Detect
Area
DOORWAY 2
Detect
Area
LOW HALF
Detect
Area
UP HALF
Detect
Area
TOP MENU SECOUND MENU THIRD MENU
BF
Lens Bright
Configure
Chroma Level
Pedestal Level
Aperture H-APT Level
V-APT Level
Sync INT *
LL V-Phase
BLC Off *
Center 1
Center 2
Door Way 1
Up Half
Low Half
Level
Door Way 2
Gamma 0.45 *
0.8
1
RS485 Address _ _ _
B-Rate 9600dps *
Address
4800dps
Password Setting Password _ _ _
Shutter AES 1/2K
1/60(1/50) *
1/100(1/120)
1/250
1/500
1/1K
1/2K
1/4K
1/10K
Bright
1/5K
1/10K
1/20K
1/50K *
1/100K
Text
CAM Tilte
Position
Off *
On
D/N IR Pass
IR Cut
Burst On
Burst Off *
Fuzzy
D/N Level Low
D/N Level High
Burst On
Burst Off *
AGC Off
18dB
26dB
30dB *
32dB
34dB
Sens Up
36dB
22dB
R-Gain
B-Gain
2500K ~ 9500K *
2000K ~ 18000K
WB - Auto *
WB - Menu
WB - Push
White Bal
NU
Set up Menu
Sync Int
Shutter
Lens
BLC
Configur
White B
Cam Tit
D/N
1/50
Bright
Off
e Aperture
al AWB
le Off
Fuzzy
RS-485 Address
Exit ResetQuit
TOP MESECOUND MENUTHIRD MENU
BFLensBrightConfigureChromaLevelPedestalLevelApertureH-APT LevelelV-APT LevSyncINT*LLV-PhaseBLCOff*Center 1Center 2Door Way 1Up HalfLow HalfLevelDoor Way 2Gamma0.45*0.81RS485Address _ _ _B-Rate9600dps*Address4800dpsPassword SettingPassword _ _ _ShutterAES1/2K1/60(1/50)*1/100(1/120)1/2501/5001/1K1/2K1/4K1/10KBright1/5K1/10K1/20K1/50K*1/100KTextCAM TiltePositionOff
*
OnD/NIR PassIR CutBurst OnBurst Off
*
FuzzyD/N LevelLowD/N LevelHighBurst OnBurst Off
*
AGCOff18dB26dB30dB
*
32dB34dBSens Up36dB22dBR-GainB-Gain2700K ~ 9100K*2500K ~ 15000KWB- Auto *
