DESi Utopic2 Series Manuel utilisateur
Wireless Motorized Cylinder with
Wireless Keypad
USER
MANUAL
UKC 60 / UKBC 60 Images on this manual are for referance only.
!
1. GENERAL INFORMATIONS and WARNINGS
- For emergancy conditions, we recommend you to put the keys to an accessible place (like car, bag etc.)
- If there is any problem with door or locking mechanism, first of all, those problems need to be solved. Door's mechanical
parts and locking mechanism should be working properly.
- If there is a problem with the device, first look to the troubleshooting part of this manual. If you cannot solve the
problem, contact with your dealer.
- Replace the batteries, if there is a battery warning. RECYCLE EMPTY BATTERIES!
- All the system need to be protected from water and shocks.
- Place the batteries after installation of the system to the door. If the batteries are placed before the installation, auto-
rotating parts may cause injuries. WATCH YOUR FINGERS!
We would like to thank you for choosing this patented product. We hope you to enjoy it.
DESi Alarm and Security System Inc.
Controlling Options and Compatible Accessories
Wireless Fingerprint Reader
Remote Controller
Wireless Auto-Locking Module
Wireless Home Automation Interface
Wireless Secretary Button
Remote Access Module
3
1.1. General Features of Devices
Structure
Engraved block alluminum, Zamak and ABS
Cylinder Length (may vary according to model)
(outside) 26 mm | 10 mm | 36 mm (inside)
Inside part can extensile up to 42 mm with extending
parts.
Batteries and Battery Life of Motorized Cylinder
5x 1,5 V AA size Alkaline or Lithium batteries.
According to tests done in DESi labratories, battery life of
the device is measured as follows:
2,5 years standby or 10.000 operations (locking or
unlocking) for 3 rotation locks
Wireless Keypad
434 Mhz Anti-duplicatiion rolling code rf communication.
Bluetooth feature (only for model UKBC 80)
1.2. Box Content (may vary according to model number)
1x Wireless Motorized Cylinder (with keys)
1x Wireless Keypad
1x Installation screw and Hex key
2. PARTS OF WIRELESS MOTORIZED CYLINDER and INSTALLATION
4
Cylinder
Handle
Handle Screw
Hex Screw
The hole
for hex key
DEMOUNTING OF MOTOR AND CYLINDER
- Open “handle screw” and remove the handle by pulling.
- Remove the batteries.
- Rotate “hex screw” to counter-clock wise by using the hex
key out of the box. You will see the cylinder will be
disassembled from the motorized part.
To assemble two parts, combine cylinder and motorized
part in a proper way and rotate hex screw to clock wise.
Metal Extending Parts
(used if needed)
Plastic Cover Cover Spring
5
(Back Cover)
Mounting
Holes
Up to 6 mm
26 10 34
26 10 40
EXTENDING INSIDE PART
OF THE CYLINDER (if needed)
If the door thickness is not
suitable to the cylinder of the
device, inside part of the
cylinder may be extended up
to 6 mm by 2 mm steps.
To extend the cylinder’s inside
part, follow the instructions
below:
- Open “handle screw” and
remove the handle by pulling.
- Remove the batteries.
- Rotate “hex screw” to counter-clock wise by using the hex key
out of the box till the motorized part is disassembled from the
cylinder.
- Add 2 mm metal extending parts as needed.
- Assemble cylinder and motorized part and rotate hex screw to
clock wise direction.
- Install the batteries and check the device if it is working
properly or not.
DisplayTouch Buttons
Locking
Button
Menu
Button
Screw for
Changing
Batteries
6
2.1. Installation of Motorized Cylinder
This is the easiest installation. It is suitable for all kind of doors.
In some security doors, even if you remove cylinder screw, you cannot remove cylinder due to cramped installation of
cylinder defender. Follow the instructions below, for that kind of situations: (Recommended for professional installers.)
- Untighten screws of cylinder defender (don’t remove the screws)
- Remove cylinder screw and take out the old cylinder.
- Disassemble the motozied part from the cylinder. (see. p.5)
- Install the cylinder part to the door and tighten the cylinder screw.
- Tighten the screws of cylinder defender.
- Assemble the motorized part with cylinder. (see. p.5)
1.STEP
Remove
existing
cylinder.
2. STEP
Install
motorized
cylinder and
tighten
the screw
That’s
it!
7
3. ADMINISTRATION ACTIONS / SETTINGS FOR KEYPAD
Two different 5 digit passwords may be defined to the keypad; 1 master, 1 user. Both of the passwords can be use to unlock
and open. For settings, the master password need to be entered. Default master password is “12345". User password is not
set.
WARNING: First fo all, change the default master password.
3.1. Changing Default Master Password
- Wake the keypad up by putting your palm to the touch keys and than touch to “M” button. “A” appears on the display.
- Enter 5 digit master password. After display animation, touch to “M” button again. “b” appears on the display.
- Touch to “1" button and enter the new master password in 5 digit. After display animation, re-enter the new master
password. In this way, the master password will be changed.
CAUTION: Before using your motorized cylinder, Direction of locking/unlocking (p.11) and Number of turns (p.11) should be
adjusted. Otherwise, the device would not work properly.
8
3.2. Defining / Changing User Password
- Wake the keypad up by putting your palm to the touch keys and than touch to “M” button. “A” appears on the display.
- Enter 5 digit master password. After display animation, touch to “M” button again. “b” appears on the display.
- Touch to “2" button and enter the new user password in 5 digit. After display animation, re-enter the new user password.
In this way, the user password will be defined / changed.
3.3. Enrolling Mobile Device (for UKBC 80 only)
Search “Desi Utopic” on stores to download and install mobile application. After installation, run the app, choose desired
language and define a password. You can disable/enable password protection or change password later.
- Wake the keypad up by putting your palm to the touch keys and than touch to “M” button. “A” appears on the display.
- Enter master password. After display animation, touch to “M” button again. “b” appears on the display. Touch to “3".
- Run the app on your mobile and touch to “ ” on main screen. The known devices will be listed. Touch to “ ” located
upper right of the list to see new device.
- Touch to UTOPIC line and enter a name for new device and touch “ ” next to name box. If you see more than one
device in the list, closest device to your mobile will be shown at the top of the list with 3 or 4 signal strength bars.
- Recognizing process will start automatically. If the matching is successful, gray control buttons at the bottom become
colorful.
9
3.4. Clearing All Mobile Devices (for UKBC 80 only)
- Wake the keypad up by putting your palm to the touch keys and than touch to “M” button. “A” appears on the display.
- Enter 5 digit master password. After display animation, touch to “M” button again. “b” appears on the display.
- Touch to “4" button and than touch to any button till the display shows “9". Touch to lock button while “9" is shown. After
that, all the mobile devices will be deleted from keypad.
3.5. Reporting Enrolled Mobile Devices (for UKBC 80 only)
- Wake the keypad up by putting your palm to the touch keys and than touch to “M” button. “A” appears on the display.
- Enter 5 digit master password. After display animation, touch to “M” button again. “b” appears on the display.
- Touch to “5" button. The display will show the number of enrolled mobile devices.
3.6. Factory Reset
After factory reset, keypad’s master password will be “12345". User password and mobile devices will be cleared.
- Wake the keypad up by putting your palm to the touch keys and than touch to “M” button. “A” appears on the display.
- Enter 5 digit master password. After display animation, touch to “M” button again. “b” appears on the display.
- Touch to “6" button and than touch to the “M” button till the display shows “9". Touch to lock button while “9" is shown.
After that, factory reset will be implimented.
10
4. SETTINGS FOR MOTORIZED KNOB
4.1. Enrolling Wireless Controllers to the Motorized Knob
- Wake the keypad up by putting your palm to the touch keys and than touch to “M” button. “A” appears on the display.
- Enter 5 digit master password. After display animation, touch to “6” button. The knob will give a long (5 sec) and a short
warning tone one after the other.
- Just after short warning tone, send from the device you want to enroll to the knob till you hear 2 warning “a RF signal”
tones from the cylinder. In this way, the new controller will be enrolled to the knob.
How to Send from Controllers“a RF Signal”
Remote Controllers: Press any button.
Secretary Button: Press the button.
Fingerprint Reader: Wake up and touch to locking button.
Keypad: Wake up and touch to lock button.
Auto-Closer: Bring the magnet closer to the device and than seperate it from device.
Home-Automation Interface: Short-circuit red and white cables and than open-circuit.
Autres manuels pour Utopic2 Series
1
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels DESi Verrouillage
