Desa LSL18NT Instructions originales

Save this manual for future reference.

For more information, visit www.desatech.com

WARNING: If the information in this manual is not fol-

lowed exactly, a ﬁre or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre

department.

— Installation and service must be performed by a quali-

ﬁed installer, service agency or the gas supplier.

18,000 BTU THERMOSTAT MODELS

LSL18NT, LSL18PT, SL18NT, SL18PT, VSL18NT AND VSL18PT

UNVENTED (VENT-FREE) BLUE FLAME GAS HEATER

SAFETY INFORMATION AND INSTALLATION MANUAL

www.desatech.com 116292-01A

WARNING: Improper installation, adjustment, altera-

tion, service or maintenance can cause injury or prop-

erty damage. Refer to this manual for correct installation

and operational procedures. For assistance or addi-

tional information consult a qualiﬁed installer, service

agency or the gas supplier.

WARNING: This is an unvented gas-ﬁred heater. It uses

air (oxygen) from the room in which it is installed. Provi-

sions for adequate combustion and ventilation air must

be provided. Refer to Air for Combustion and Ventilation

section on page 5 of this manual.

This appliance may be installed in an aftermarket,* per-

manently located, manufactured (mobile) home, where

not prohibited by local codes.

This appliance is only for use with the type of gas indi-

cated on the rating plate. This appliance is not convert-

ible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

State of Massachusetts: The installation must be made by a licensed plumber or gas ﬁtter in the

Commonwealth of Massachusetts.

Sellers of unvented propane or natural gas-ﬁred supplemental room heaters shall provide to each

purchaser a copy of 527 CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for bedroom and bathroom installation in the Common-

wealth of Massachusetts.

TABLE OF CONTENTS

Safety Information ............................................... 3

Local Codes ........................................................ 4

Product Identiﬁcation ........................................... 4

Unpacking ........................................................... 4

Product Features ................................................. 4

Air For Combustion And Ventilation ..................... 5

Installation ........................................................... 7

Operating Heater ............................................... 14

Inspecting Heater ............................................. 16

Cleaning and Maintenance ................................ 17

Troubleshooting ................................................. 18

Speciﬁcations .................................................... 22

Wiring Diagrams ................................................ 22

Accessories ....................................................... 23

Technical Service .............................................. 23

Service Publications .......................................... 23

Replacement Parts ............................................ 23

Service Hints ..................................................... 23

Illustrated Parts Breakdown and Parts List ....... 24

Parts Centrals .................................................... 26

Warranty Information ......................................... 28

www.desatech.com

116292-01A 3

SAFETY INFORMATION

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble,

operate or service this heater.

Improper use of this heater can

cause serious injury or death

from burns, fire, explosion,

electrical shock and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of carbon

monoxide poisoning resemble the ﬂu, with head-

aches, dizziness or nausea. If you have these signs,

the heater may not be working properly. Get fresh

air at once! Have heater serviced. Some people

are more affected by carbon monoxide than others.

These include pregnant women, people with heart

or lung disease or anemia, those under the inﬂuence

of alcohol and those at high altitudes.

Natural and Propane/LP Gas: Natural and

propane/LP gases are fuel gases. Fuel gases are

odorless. An odor-making agent are added to fuel

gases. The odor helps you detect a fuel gas leak.

However, the odor added to fuel gas can fade. Fuel

gas may be present even though no odor exists.

Make certain you read and understand all warn-

ings. Keep this manual for reference. It is your

guide to safe and proper operation of this heater.

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not use a

blower insert, heat exchanger

insert or other accessory not ap-

proved for use with this heater.

Due to high temperatures, the

appliance should be located out

of trafﬁc and away from furniture

and draperies.

Do not place clothing or other

ﬂammable material on or near

the appliance. Never place any

objects on the heater.

Surface of heater becomes very

hot when running heater. Keep

children and adults away from

hot surface to avoid burns or

clothing ignition. Heater will

remain hot for a time after shut-

down. Allow surface to cool

before touching.

Carefully supervise young chil-

dren when they are in the same

room with heater.

Make sure grill guard is in place

before running heater.

Keep the appliance area clear

and free from combustible ma-

terials, gasoline and other ﬂam-

mable vapors and liquids.

1. This appliance is only for use with the type of

gas indicated on the rating plate. This appliance

is not convertible for use with other gases.

2. Do not place propane/LP supply tank(s) in-

side any structure. Locate propane/LP supply

tank(s) outdoors.

3. This heater shall not be installed in a bathroom

or a bedroom.

4. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from a

neighborʼs phone. Follow the gas supplierʼs

instructions

• if you cannot reach your gas supplier, call

the ﬁre department

5. This heater needs fresh, outside air ventilation

to run properly. This heater has an Oxygen

Depletion Sensing (ODS) safety shutoff

system. The ODS shuts down the heater if

not enough fresh air is available. See Air for

Combustion and Ventilation, page 5.

www.desatech.com 116292-01A

6. Keep all air openings in front and bottom of

heater clear and free of debris. This will insure

enough air for proper combustion.

7. If heater shuts off, do not relight until you

provide fresh, outside air. If heater keeps

shutting off, have it serviced.

8. Do not run heater

• where ﬂammable liquids or vapors are used

or stored

• under dusty conditions

9. Before using furniture polish, wax, carpet

cleaner or similar products, turn heater off. If

heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls or furniture.

10. Do not use heater if any part has been under

water. Immediately call a qualiﬁed service

technician to inspect the room heater and to

replace any part of the control system and any

gas control which has been under water.

11. Turn off and let cool before servicing. Only

a qualiﬁed service person should service and

repair heater.

12. Operating heater above elevations of 4,500

feet (1,371 m) could cause pilot outage.

13. To prevent performance problems, do not use

propane/LP fuel tank of less than 100 lbs. (45 kg)

capacity.

14. Provide adequate clearances around air

openings.

LOCAL CODES

Install and use heater with care. Follow all lo-

cal codes. In the absence of local codes, use the

latest edition of National Fuel Gas Code, ANSI

Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

SAFETY INFORMATION

Continued

Figure 1 - Vent-Free Gas Heater

Ignitor

Control Knob

(under door)

Heater Cabinet

Glass Panel

PRODUCT

IDENTIFICATION

UNPACKING

1. Remove heater from carton.

2. Remove all protective packaging applied to

heater for shipment.

3. Check heater for any shipping damage. If

heater is damaged, promptly inform dealer

where you bought heater.

PRODUCT FEATURES

SAFETY DEVICE

This heater has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free room

heaters. The ODS/pilot shuts off the heater if there

is not enough fresh air.

IGNITION SYSTEM

This heater has either a piezo ignitor or electronic

ignitor to light heater fuel supply.

THERMOSTATIC HEAT CONTROL

Thermostat models have a thermostat sensing

bulb and a control valve. This results in the great-

est heater comfort. This can also result in lower

gas bills.

www.desatech.com

116292-01A 5

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This heater shall

not be installed in a conﬁned

space or unusually tight con-

struction unless provisions are

provided for adequate combus-

tion and ventilation air. Read the

following instructions to insure

proper fresh air for this and

other fuel-burning appliances

in your home.

Todayʼs homes are built more energy efﬁcient

than ever. New materials, increased insulation and

new construction methods help reduce heat loss

in homes. Home owners weather strip and caulk

around windows and doors to keep the cold air out

and the warm air in. During heating months, home

owners want their homes as airtight as possible.

While it is good to make your home energy efﬁ-

cient, your home needs to breathe. Fresh air must

enter your home. All fuel-burning appliances need

fresh air for proper combustion and ventilation.

Exhaust fans, ﬁreplaces, clothes dryers and fuel

burning appliances draw air from the house to

operate. You must provide adequate fresh air for

these appliances. This will insure proper venting

of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Section 5.3,

Air for Combustion and Ventilation.

All spaces in homes fall into one of the three fol-

lowing ventilation classiﬁcations:

1. Unusually Tight Construction

2. Unconﬁned Space

3. Conﬁned Space

The information on pages 5 through 7 will help

you classify your space and provide adequate

ventilation.

Unusually Tight Construction

The air that leaks around doors and windows

may provide enough fresh air for combustion and

ventilation. However, in buildings of unusually

tight construction, you must provide additional

fresh air.

Unusually tight construction is deﬁned as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of

one perm (6x10-11 kg per pa-sec-m2) or

less with openings gasketed or sealed

and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window

and door frames, between sole plates

and ﬂoors, between wall-ceiling joints,

between wall panels, at penetrations

for plumbing, electrical and gas lines

and at other openings.

If your home meets all of the three criteria

above, you must provide additional fresh

air. See Ventilation Air From Outdoors,

page 7.

If your home does not meet all of the

three criteria above, proceed to Determin-

ing Fresh-Air Flow For Heater Location,

page 6.

Conﬁned and Unconﬁned Space

The National Fuel Gas Code, ANSI Z223.1/NFPA

54 deﬁnes a conﬁned space as a space whose

volume is less than 50 cubic feet per 1,000 Btu

per hour (4.8 m3 per kw) of the aggregate input

rating of all appliances installed in that space and

an unconﬁned space as a space whose volume is

not less than 50 cubic feet per 1,000 Btu per hour

(4.8 m3 per kw) of the aggregate input rating of

all appliances installed in that space. Rooms com-

municating directly with the space in which the

appliances are installed*, through openings not

furnished with doors, are considered a part of the

unconﬁned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation grills

between them.

www.desatech.com 116292-01A

AIR FOR COMBUSTION

AND VENTILATION

Continued

DETERMINING FRESH-AIR FLOW

FOR HEATER LOCATION

Determining if You Have a Conﬁned or

Unconﬁned Space

Use this work sheet to determine if you have a con-

ﬁned or unconﬁned space.

Space: Includes the room in which you will install

heater plus any adjoining rooms with doorless pas-

sageways or ventilation grills between the rooms.

1. Determine the volume of the space (length x

width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (6.1 m) (length) x 16

ft. (4.88 m)(width) x 8 ft. (2.44 m) (ceiling height)

= 2560 cu. ft. (72.49 m3) (volume of space)

If additional ventilation to adjoining room is

supplied with grills or openings, add the volume

of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

_______ (volume of space) x 20 = (Maximum

Btu/Hr the space can support)

Example: 2560 cu. ft. (72.49 m3) (volume of

space) x 20 = 51,200 (maximum Btu/Hr the space

can support)

3. Add the Btu/Hr of all fuel burning appliances in

the space.

Vent-free heater ___________ Btu/Hr

Gas water heater* ___________ Btu/Hr

Gas furnace ___________ Btu/Hr

Vented gas heater ___________ Btu/Hr

Gas ﬁreplace logs ___________ Btu/Hr

Other gas appliances* + __________ Btu/Hr

Total = __________ Btu/Hr

* Do not include direct-vent gas appliances. Di-

rect-vent draws combustion air from the outdoors

and vents to the outdoors.

Example:

Gas water heater ___________ Btu/Hr

Vent-free heater + __________ Btu/Hr

Total = __________ Btu/Hr

40,000

18,000

58,000

4. Compare the maximum Btu/Hr the space can

support with the actual amount of Btu/Hr used.

_________

Btu/Hr (maximum the space can support)

_________

Btu/Hr (actual amount of Btu/Hr used)

Example: 51,200 Btu/Hr (maximum the space

can support)

58,000 Btu/Hr (actual amount of

Btu/Hr used)

The space in the above example is a conﬁned space

because the actual Btu/Hr used is more than the maxi-

mum Btu/Hr the space can support. You must provide

additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoin-

ing room. If the extra space provides an unconﬁned

space, remove door to adjoining room or add

ventilation grills between rooms. See Ventilation

Air From Inside Building, page 7.

B. Vent room directly to the outdoors. See Ventila-

tion Air From Outdoors, page 7.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size

makes room unconﬁned.

If the actual Btu/Hr used is less than the maximum

Btu/Hr the space can support, the space is an uncon-

ﬁned space. You will need no additional fresh air

ventilation.

WARNING: If the area in

which the heater may be oper-

ated is smaller than that deﬁned

as an unconﬁned space or if the

building is of unusually tight

construction, provide adequate

combustion and ventilation air

by one of the methods described

in the National Fuel Gas Code,

ANSI Z223.1/NFPA 54 Section 5.3

or applicable local codes.

www.desatech.com

116292-01A 7

Figure 3 - Ventilation Air from Outdoors

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining un-

conﬁned space. When ventilating to an adjoining

unconﬁned space, you must provide two perma-

nent openings: one within 12" (30.4 cm) of the

ceiling and one within 12" (30.4 cm) of the ﬂoor

on the wall connecting the two spaces (see options

1 and 2, Figure 2). You can also remove door into

adjoining room (see option 3, Figure 2). Follow the

National Fuel Gas Code, ANSI Z223.1/NFPA 54,

Section 5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

Figure 2 - Ventilation Air from Inside

Building

Remove

Door into

Adjoining

Room,

Option 3

Ventilation Grills

Into Adjoining Room,

Option 2

12"

(30.4 cm)

Ventilation

Grills

into Adjoining

Room,

Option 1

12"

(30.4 cm)

Outlet

Air

Ventilated

Attic

Outlet

Inlet

Air

Inlet Air Ventilated

Crawl Space

Crawl

Space

To Attic

AIR FOR COMBUSTION

AND VENTILATION

Continued

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualiﬁed ser-

vice person must install heater.

Follow all local codes.

CHECK GAS TYPE

Use only the correct type of gas (natural or pro-

pane/LP). If your gas supply is not the correct gas

type, do not install heater. Call dealer where you

bought heater for proper type heater.

WARNING: This appliance

is equipped for (natural or pro-

pane/LP) gas. Field conversion

is not permitted.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills

or ducts. You must provide two permanent open-

ings: one within 12" (30.4 cm) of the ceiling and

one within 12" (30.4 cm) of the ﬂoor. Connect

these items directly to the outdoors or spaces

open to the outdoors. These spaces include attics

and crawl spaces. Follow the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for

Combustion and Ventilation for required size of

ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet

or outlet air into attic if attic has a thermostat-

controlled power vent. Heated air entering the attic

will activate the power vent.

www.desatech.com 116292-01A

INSTALLATION ITEMS

Before installing heater, make sure you have the

items listed below.

• for propane/LP gas, external regulator (supplied

by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• ground joint union

• sediment trap

• tee joint

• pipe wrench

• for natural gas, test gauge connection*

* A CSA design-certiﬁed equipment shutoff valve

with 1/8" NPT tap is an acceptable alternative to

test gauge connection. The optional CSA design-

certiﬁed equipment shutoff valve can be purchased

from your dealer. See Accessories, page 23.

LOCATING HEATER

This heater is designed to be mounted on a wall.

WARNING: Maintain the

minimum clearances shown

in Figure 4. If you can, provide

greater clearances from ﬂoor,

ceiling and joining wall.

WARNING: Never install the

heater

• in a bathroom or a bedroom

• in a recreational vehicle

• where curtains, furniture,

clothing or other ﬂammable

objects are less than 36 inches

(92 cm) from the front, top or

sides of the heater

• as a ﬁreplace insert

• in high trafﬁc areas

• in windy or drafty areas

Figure 4 - Mounting Clearances As

Viewed From Front of Heater

INSTALLATION

Continued CAUTION: This heater cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to heater. Installing

heater next to vinyl or cloth wall

coverings or operating heater

where impurities (such as, but

not limited to, tobacco smoke,

aromatic candles, cleaning ﬂu-

ids, oil or kerosene lamps, etc.) in

the air exist, may discolor walls

or cause odors.

IMPORTANT: Vent-free heaters add moisture to

the air. Although this is beneﬁcial, installing heater

in rooms without enough ventilation air may cause

mildew to form from too much moisture. See Air

for Combustion and Ventilation, page 5. If high hu-

midity is experienced, a dehumidiﬁer may be used

to help lower the water vapor content in the air.

CAUTION: If you install the

heater in a home garage

• heater pilot and burner must

be at least 18 inches (45.7 cm)

above ﬂoor

• locate heater where moving

vehicle will not hit it

For convenience and efﬁciency, install heater

• where there is easy access for operation, inspec-

tion and service

• in coldest part of room

Locate heater near a 120V 60Hz electrical outlet

(normal household voltage).

Minimum

From

Sides Of

Heater

36"

(91.4 cm)

Minimum

2" (5.1 cm)

FLOOR

CEILING

Minimum To

Top Surface

Of Carpeting,

Tile Or Other

Combustible

Material

Left

Side

Right

Side

6" (15.2 cm)

www.desatech.com

116292-01A 9

INSTALLATION

Continued

INSTALLING HEATER TO WALL

Mounting Bracket

Locate mounting bracket in heater carton. Remove

mounting bracket from heater carton.

Figure 7 - Installing Glass Panel

Figure 5 - Mounting Bracket

Removing Front Panel Of Heater

1. Remove the four screws, two on each side of

front panel.

2. Pull front panel forward from the bottom, only

2 to 3 inches (5 to 7.6 cm).

3. Reach into lower right corner of heater and

disconnect ignitor wire.

4. Lift panel up to remove, set aside.

5. Remove any remaining packaging materials.

4. Turn front panel face down. Gently press onto

a hard surface to snap bushing into hole. Turn

panel back over, face up.

5. Place spacers over 4 holes on front panel as

shown in Figure 7.

6. Position glass on top of spacers, aligning holes.

Note: If glass gets scratched or marred from

normal use, it may be reversed on heater.

7. Place 4 retaining clips on glass over holes.

8. Install screws in each hole, but do not tighten

at this time.

9. Square glass up with top front surface of front

panel. Tighten screws.

10. Snap screw covers over retaining clips.

Glass Panel

Screw Cover

Front

Panel

Spacer

Screw

Retainer Clip

Installing Glass Panel

Items needed from hardware packet:

1 - Bushing

4 - Black spacers

4 - Retaining clips

4 - 1.5" long screws

4 - Screw covers

1. Locate hardware packet and dark acrylic glass.

Peel protective coating from both sides of glass.

3. Snap bushing into center front hole of front

panel (see Figure 7).

Figure 6 - Removing Front Panel Of Heater

Screw

Front Panel

Methods For Attaching Mounting Bracket

To Wall

Only use last hole on each end of mounting bracket

to attach bracket to wall. These two holes centers are

13 inches (33 cm) apart. Attach mounting bracket to

wall in one of two ways:

1. Attaching to wall stud

2. Attaching to wall anchor

Attaching to Wall Stud: This method provides the

strongest hold. Insert mounting screws through

mounting bracket and into wall studs.

Attaching to Wall Anchor: This method allows you

to attach mounting bracket to hollow walls (wall

areas between studs) or to solid walls (concrete

or masonry).

Decide which method better suits your needs.

Either method will provide a secure hold for the

mounting bracket.

Marking Screw Locations

1. Tape mounting bracket to wall where heater

will be located. Make sure mounting bracket

is level.

Ignitor

Wire

Bushing

www.desatech.com 116292-01A

INSTALLATION

Continued

Figure 9 - Folding Anchor

Figure 11 - Mounting Heater Onto

Mounting Bracket

Figure 10 - Popping Open Anchor Wings

For Thin Walls

Mounting Bracket

(attached to wall)

Horizontal Slots

Stand-Out Tab

WARNING: Maintain mini-

mum clearances shown in Figure

8. If you can, provide greater

clearances from ﬂoor and join-

ing wall.

2. Mark screw locations on wall (see Figure 8).

Note: Only mark last hole on each end of

mounting bracket. Insert mounting screws

through these holes only.

3. Remove tape and mounting bracket from

wall.

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws and spacers

are in hardware package. The hardware package

is provided with heater.

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs

1. Drill holes at marked locations using 9/64"

drill bit.

2. Place mounting bracket onto wall. Line up last

hole on each end of bracket with holes drilled

in wall.

3. Insert mounting screws through bracket and

into wall studs.

4. Tighten screws until mounting bracket is

ﬁrmly fastened to wall studs.

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow walls

(wall areas between studs) or solid walls (concrete

or masonry)

1. Drill holes at marked locations using 5/16"

drill bit. For solid walls (concrete or masonry),

drill at least 1" deep.

2. Fold wall anchor as shown in Figure 9.

13" (33 cm)

11"

(27.9 cm)

Min.

12"

(30.4

cm)

Min.

Adjoining Wall

Only Insert Mounting

Screws Through Last

Hole On Each End

Floor

Figure 8 - Mounting Bracket Clearances

3. Insert wall anchor (wings ﬁrst) into hole. Tap

anchor ﬂush to wall.

4. For thin walls [1/2" (1.3 cm) or less], insert red

key into wall anchor. Push red key to “pop” open

anchor wings. IMPORTANT: Do not hammer

key! For thick walls [over 1/2" (1.3 cm) thick]

or solid walls, do not pop open wings.

5. Place mounting bracket onto wall. Line up

last hole on each end of bracket with wall

anchors.

6. Insert mounting screws through bracket and

into wall anchors.

7. Tighten screws until mounting bracket is

ﬁrmly fastened to wall.

Placing Heater On Mounting Bracket

1. Locate two horizontal slots on back panel of

heater.

2. Place heater onto mounting bracket. Slide

horizontal slots onto stand-out tabs on mount-

ing bracket.

Autres manuels pour LSL18NT

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Desa Chauffage au gaz

Desa

Desa Vanguard VVDA18R Guide de démarrage rapide

Desa

Desa 24" Variably-Controlled Models Guide de démarrage rapide

Desa

Desa Comfort Glow CGN18R Guide de démarrage rapide

Desa

Desa Glo-Warm FB-5B Guide de démarrage rapide

Desa

Desa GN30 Instructions originales

Desa

Desa GWP10 GWN10T Manuel utilisateur

Desa

Desa VGL18PRA Guide de démarrage rapide

Desa

Desa CTB3924PR Guide de démarrage rapide

Desa

Desa Comfort Glow CGR2N Guide de démarrage rapide

Desa

Desa Medallion MR10NT Guide de démarrage rapide

Desa

Desa GWRN18 Instructions originales

Desa

Desa Vanguard VP600BA Guide de démarrage rapide

Desa

Desa Comfort Glow CGR2P Guide de démarrage rapide

Desa

Desa Comfort Glow CGP16RA Guide de démarrage rapide

Desa

Desa Comfort Glow CGP10TLA Guide de démarrage rapide

Desa

Desa 30 Guide de démarrage rapide

Desa

Desa GN30T Instructions originales

Desa

Desa RN30BT Guide de démarrage rapide

Desa

Desa 10542 Instructions originales

Desa

Desa Glo-Warm FA-20BB Guide de démarrage rapide

Desa

Desa Comfort Glow CGS2718P Fiche technique

Desa

Desa CDR3924NT Guide de démarrage rapide

Desa

Desa GMP16 Instructions originales

Desa

Desa RCP200V Manuel utilisateur

Manuels Chauffage au gaz populaires d'autres marques

Superior

Superior BGE18NV Manuel utilisateur

Dru

Dru Room-sealed atmospheric gas-fired heating... Manuel utilisateur

klover

klover TKR 35 Manuel utilisateur

Rothenberger Industrial

Rothenberger Industrial 035984 Manuel utilisateur

New Buck Corporation

New Buck Corporation 34 Manuel utilisateur

Hargrove

Hargrove Timberland Glow Guide de démarrage rapide

Kinder

Kinder Cameo BF Manuel utilisateur

Qlima

Qlima GH 438 B-2 Manuel

Gasmate

Gasmate AH100 Series Manuel utilisateur

Medallion

Medallion MBP20TLB Guide de démarrage rapide

Clarke

Clarke DEVIL 910SS Manuel utilisateur

Superior

Superior BGE18NR Manuel utilisateur

Brant Radiant Heaters

Brant Radiant Heaters QTD Series Instructions d'installation

L.B. White

L.B. White Therma Grow HW220 Manuel

Sealey

Sealey LP35.V5 Manuel utilisateur

Italkero

Italkero Falo Evo Manuel utilisateur

Williams

Williams 2509822A Manuel utilisateur

Romotop

Romotop Heckla 1301 Caractéristiques techniques