DentalEZ EverLight Manuel utilisateur

User Manual

EverLight®

Post Mount

User Manual

Table of Contents

Section I Introduction

Specications .......................................................................................................................... 2

 Classications......................................................................................................................2-3

 LightHeadRangeofMotion............................................................................................... 3

 Dimensions ............................................................................................................................. 4

 Packaging ................................................................................................................................. 4

Section II Installation

PostMountwithServiceConsole..................................................................................5-6

 PostMountforMagellanCMU .......................................................................................... 6

Section III Operation

LightSwitch............................................................................................................................. 7

 TouchPads .............................................................................................................................. 7

 PositioningLight..................................................................................................................... 8

 EliminatingAdjustableArmDrift........................................................................................ 9

Section IV Care

 Cleaning&Disinfecting ...................................................................................................... 10

Section V User Service Information

Troubleshooting................................................................................................................... 11

 ServiceInstruction .............................................................................................................. 11

 DisposalofEquipment........................................................................................................ 11

Section VI Parts List/Diagrams

LightArm............................................................................................................................... 12

 LightHead............................................................................................................................. 12

Limited Warranty ........................................................................................................ 13

Wiring Schematic ........................................................................................................ 14

EMC Information .................................................................................................... 15-18

User Manual

EverLight® (Post Mount)

Section I Introduction

Classications

Medical-GeneralMedicalEquipment

Certiedastoelectricalshock,re

andmechanicalhazardsonlyinaccor-

dancewithUL60601-1,

CAN/CSA-C22.2No.601.1,

CAN/CSA-C22.2No.60601-1(2008)&

ANSI/AAMIES60601-1(2005).

–Type of protection against electric shock: Class 1

Equipment

–Degree of protection against the ingress of water:

Ordinary

–Equipment not suitable for use in the presence of

a ammable anesthetic mixture with air or with

oxygen or nitrous oxide.

–Mode of operation: Continuous

–Environmental conditions recommended ranges

for:

Transport and Storage:

- Temperature range of - 10º C to + 70º C

- Relative humidity range of 10% to 100%

- Atmospheric pressure range of 500 to 1060 kPa

Normal Use:

- Temperature range of + 10º C to + 40º C

- Relative humidity range of 30% to 75%

- Atmospheric pressure range of 700 to 1060 kPa

Power Supply: Primary: 100-240V AC, 50/60 Hz.

Secondary: 12V DC

Operating Amperage: .4 max. - .16 min. Amp

Focal Length: 68.6 cm (27")

Color Temperature: High: 5800° Kelvin

(Color Matching)

Medium: 4500° Kelvin

(Operative Setting)

Low: 3200° Kelvin

(Composite Setting)

Light Intensity: High: 2790 Footcandles

(30,000 Lux)

Medium: 2325 Footcandles

(25,000 Lux)

Low: 1395 Footcandles

(15,000 Lux)

Light Pattern: 16.5 cm (6-1/2") x 8.9 cm (3-1/2")

Unit Weight: Post Mount: 12 kg (27 lbs.)

TheauthorizedEuropeanrepresentativeis:

DentalEZ(GB)Ltd.  

ClevelandWay

HemelHempstead,Hertfordshire

HP27DY,England

Phone:(01442)269301

Attn:Mr.AndyKing

This manual contains installation, operation and care

instructions and user service information for the

EverLight® LED operatory light.

The EverLight operatory light system is intended to

be used by trained professional dental care personnel

to provide shadow free illumination to the oral cavity

for dental practices. The operatory light arm system

allows optimal light positioning, which for a reclined

patient, is normally from the sagittal plane directly

above or slightly behind the patient's oral cavity. The

operator will typically be positioned behind or to one

side of the patient. The arm assembly is counterbal-

anced so that minimum force is required to move

the light head assembly. The operatory light is not

designed to handle any external loads, such as hanging

foreign objects from the light system.

The EverLight operatory light is designed to provide

trouble-free service when installed, operated and

maintained according to the procedures set forth in

this manual.

To ensure correct installation, carefully read all

the instructions contained in this manual

paying close attention to all notes, notices,

cautions and warnings.

After the light is installed, please review the operation

procedures and care guidelines with the doctor's staff.

Then leave this manual in the doctor's ofce for

future reference.

53HN

Specications

In accordance with Part 15 of FCC rules, this

equipment was tested and complies with Class

A digital device limits. These limits are designed

to give equipment reasonable protection against

detrimental interference when operated in a

commercial environment.

Medical electrical equipment needs special

precautions regarding electromagnetic

compatibility (EMC) and needs to be installed

according to EMC information. (See EMC

Information Pgs. 15 through 18.)

Mobile radio frequency (RF) communications

equipment can effect medical electrical

equipment.

Section I Introduction

=Caution

 =Warning

 =Biohazard

 =WarningDangerousVoltage

 =AlternatingCurrent

 =DirectCurrent

 =TypeBAppliedPart

 =ProtectiveEarth(ground)

 =GeneralMandatoryAction

 =RefertoManual(followinstructions)

= EuropeanCertication,ifapplicable.

  Seenameplate.

 =SerialNumber

 =ManufactureDate

 =Manufacturer

Light Head Range of Motion

NOTICE

145º

180º

150º

Explanation of Symbols and Signs:

User Manual

EverLight® (Post Mount)

Section I Introduction

Dimensions

The EverLight components are packaged and shipped

according to the packing list below. Please verify the

carton contents against the packing list.

Post-Mount Packing List

•Light Arm Assembly

•Light Post

• Flanged Bronze Bushing (optional)

• Power Supply Box

•Hardware Package

•Damage Instructions

•Manual

•Warranty Card

NOTE:Be aware that some cartons are shipped as

llers and may be empty (even if optional components

are ordered).

Carefully unpack the light. Inspect all of the items

received to assure there has been no shipping damage.

If damage is discovered, contact the carrier

immediately. Then report and le the appropri-

ate claims with the carrier within 24 hours after

delivery. (See Limited Warranty, Page 13.)

Light Arm

Assembly

Light Post

Post-Mount Arm Assembly Dimensions

15"

17"

7.25"

24" 31.75"

1.701"

Packaging

For any questions about an order, please

contact a DentalEZ Equipment customer service

representative at 1-866-DTE-INFO.

NOTICE

All parts supplied are vital for proper installation.

Do not discard any hardware or components until

installation is complete.

NOTICE

Section II Installation

Isolating the light from the supply mains is accomplished

by unplugging the light from its power supply.

NOTICE

Installation by an authorized DentalEZ dealer service

technician is recommended.

NOTICE

Do not modify this equipment without authorization

from the manufacturer.

WARNING

Light Post

Set Screw

Spindle Slot

Light Arm

Assembly

NOTE: Refer to your chair mounted unit manual for

installation of the light pole.

NOTE: The post-mount arm assembly dimen-

sions are illustrated at the top of Page 4.

NOTE: The side covers of the post mount service

console must be off. Refer to the unit manual for

removal.

NOTE: If the chair's seat upholstery was installed,

remove it according to the respective chair's manual.

Light Arm Assembly

1. Place the chair base in its lowest position.

2. Disconnect the chair power.

3. Back out the set screw from the light post.

4. Apply a light coat of lubricant to the spindle.

7. Insert the light arm assembly into the bushing

until it is fully seated in the light post.

8. Using a 5/64 Allen wrench, turn the set screw

in the light post until it passes through the

light arm assembly spindle slot and engages

the light arm assembly. Then loosen the set

screw two revolutions for clearance.

Power Supply Box

1. Inside the post-mounted service console, plug the

operatory light cord into the power supply cord.

Power

Supply

Supplied

Power Cord

5. Feed the low-voltage operatory light cord

through the center of the light post, arm

pivot and console post into the post-mounted

service console.

6. Pull the light cord all the way through the

post-mounted service console until the cord is

not too tight or loose going through the posts.

To avoid the risk of electrical shock, this

equipment must only be connected to a

supply mains with protective earth.

Before proceeding with electrical installation,

all wiring must be in accordance with NEC

and local electrical codes.

WARNING

Rating of main circuit breakers should be

20 Amp maximum.

CAUTION

Post Mount with Service Console

2. Plug the supplied power cord into the power supply.

User Manual

EverLight® (Post Mount)

Section II Installation

Post Mount for Magellan CMU

3. Route the supplied power cord through the

bottom of the console and into the front of

the chair. (P-clamps provided in bag of supplies.)

5. Roll up any excess wires and neatly place

the power supply and excess wires inside the

console making sure no wires interfere with

closure of the console covers.

6. Replace the side covers on the console.

7. Reconnect the chair power and test the light

switch as described in Section III Operation.

Light Arm Assembly

1. Place the chair in its lowest position.

2. Disconnect the chair power.

3. Apply a light coat of lubricant to the spindle.

4. Slide the bushing (lipped end rst) over the light

cord and onto the spindle.

5. Feed the light cord through the center of the

light pole, pulling the cord out of the bottom

of the pole.

Power Supply Box

1. Plug the supplied power cord into the power

supply. (See photo below.)

2. Plug the light harness from the light arm into

the power supply.

3. Route the supplied power cord harness

through the front of the seat casting and plug

it into the chair harness. (See second photo on this

page.)

4. Roll up any excess wire and neatly place them

inside the seat casting making sure no wires

will interfere with moving parts. (Wire ties

provided in bag of supplies.)

5. Using the supplied Velcro, adhere the power

supply to the magellan manifold cover.

4. Plug the supplied power cord into the chair

harness located inside the chair.

P-Clamp

Console

Supplied

Power Cord

Chair Harness

Supplied

Power Cord

NOTE: Refer to the Magellan Unit Installation

Manual for installation of the light pole.

NOTE: If the chair's seat upholstery was installed,

remove it according to the respective chair's manual.

Magellan Manifold

Cover

Power

Supply

6. Reconnect the chair power and test the light

switch as described in Section III Operation.

NOTE: Replace the seat upholstery if it was removed.

Power

Cord

Section III Operation

Designed with three procedural and three intensity

settings EverLight offers a total of nine settings to

assure the correct light in every procedure.

Procedural Settings

•A- Sun - Color Matching - 5800° Kelvin

•B - Sun/Bulb - Operative Setting - 4500° Kelvin

•C - Bulb - Composite Setting - 3200° Kelvin

Low

(15,000 Lux)

Sun/Bulb - 4500°Kelvin

(Operative Setting)

Bulb - 3200°Kelvin

(Composite Setting)

Sun - 5800°Kelvin

(Color Matching)

Procedural

Settings

Intensity

Settings

Intensity Settings

•1 - Low - 15,000 Lux

•2 - Medium - 25,000 Lux

•3 - High - 30,000 Lux

Medium

(25,000 Lux)

High

(30,000 Lux)

The light ON/OFF toggle switch is located on the

elbow section of the light arm assembly.

Toggle

Switch

•Flip the toggle switch to the UP to turn the light ON.

•Flip the toggle switch DOWN to shut the light OFF.

OFF

The EverLight dental light is designed to provide illu-

mination of the oral cavity for use by dental profes-

sionals in the dental operatory.

Light Switch

Touchpads

User Manual

EverLight® (Post Mount)

Section III Operation

Using the handles on either side of the LED head,

position the light to illuminate the oral cavity. (See

Light Head Range Of Motion, Pg. 3.)

Handles

Positioning Light

To take full advantage of the EverLight's intensity

and color correction, position the light between 20"

and 45" away from the oral cavity.

NOTICE

Section III Operation

The adjustable arm is factory-adjusted to counter-

balance the weight of the light head. If it becomes

necessary to adjust the mechanism because of added

weight, such as a mirror, perform the following steps:

Tools Required

•5/64 Allen wrench

•9/64 Allen wrench

•Phillips-head screwdriver

•Large at-head (slotted) screwdriver

1. Using a Phillips-head screwdriver, loosen the

#6 screw under the cap at the end of the

adjustable arm nearest the light head.

2. Using a 5/64 Allen wrench, remove the four

Allen-head screws from the underside of the

adjustable arm (two on each end). Then slide off

the top cover along with the end cap.

3. Insert a 9/64 Allen wrench into the two small

holes in the side of the adjustable arm and

completely loosen the friction block.

4. Insert a large at-head screwdriver into the

large slot in the side of the adjustable arm and

tighten the slotted nut.

5. Adjust the friction block to provide one to

two pounds maximum of break-away force.

6. Replace the adjustable arm cover and secure

using the four 5/64 Allen-head screws

previously removed.

7. Replace the end cap and tighten the #6 screw

using a Phillips-head screwdriver.

Adjustable Arm

Top Cover

5/64 Allen-head Screws (2)

End Cap

5/64 Allen-head

Screws (2)

9/64 Allen

Wrench

Tw o

Small

Holes

Friction Block

Adjustable

Arm

Adjustable Arm

Large

Slot

Slotted

Nut

Large Flat-head

Screwdriver

Set

Screw

End Cap

Adjustable

Arm

Eliminating Adjustable Arm Drift

Table des matières

Autres manuels DentalEZ Lampe de travail

DentalEZ

DentalEZ Simplicity Manuel utilisateur

Manuels Lampe de travail populaires d'autres marques

ANSMANN

ANSMANN POWERLIGHT 5.1 Manuel utilisateur

RTRMAX

RTRMAX RTX1868 Manuel utilisateur

FeinTech

FeinTech LAL00220 Manuel utilisateur

Bunker Hill Security

Bunker Hill Security 64735 Manuel utilisateur

Goobay

Goobay 30450 Manuel utilisateur

REV Ritter

REV Ritter SPOT Manuel utilisateur

Ignition

Ignition Stagepix Line 100 IP Manuel utilisateur

SCANGRIP

SCANGRIP DUO CONNECT Manuel utilisateur

Bosch

Bosch GLI 18 V Manuel utilisateur

Bayco

Bayco SL-1514 Manuel utilisateur

EUFAB

EUFAB SMD LED 8+1 Manuel utilisateur

DeWalt

DeWalt DCL510 Manuel utilisateur

PowerSmith

PowerSmith PWLD080T Manuel utilisateur

MaxLite

MaxLite 73683 Manuel utilisateur

Heitronic

Heitronic Trend 27867 Manuel utilisateur

Monzana

Monzana Gore MZCL10 Manuel utilisateur

EINHELL

EINHELL TE-CL 18/2000 LiAC Manuel utilisateur

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Manuel utilisateur