Denali LAH.23.10200 Manuel utilisateur

Instruction Rev03

0mm 10 20 30 40 50 60 70 80 90

Thank you for choosing DENALI

We know you would rather be riding your bike than wrenching on it, so we go the extra

mile to make sure our instructions are clear and as easy to understand as possible. If

you have any questions, comments, or suggestions don’t hesitate to give our gear

experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM

Please Read Before Installing

DENALI products should always be installed by a qualified motorcycle technician. If

you are unsure of your ability to properly install a product, please have the product

installed by your local motorcycle dealer. DENALI takes no responsibility for damages

caused by improper installation. Caution: When installing electronics it is extremely

important to pay close attention to how wires are routed, especially when mounting

products to the front fender, front forks, or fairing of your motorcycle. Always be sure

to turn the handlebars fully left, fully right, and fully compress the suspension to

ensure the wires will not bind and have enough slack for your motorcycle to operate

properly.

Installation Tips

We strongly recommend using medium strength liquid thread locker on all screws,

nuts, and bolts. It is also important to ensure that all hardware is tightened to the

proper torque specifications as listed in your owner’s manual. For included accessory

hardware please refer to the default torque specifications provided below. Inspect all

hardware after the first 30 miles to ensure proper torque specifications are

maintained.

Hardware Sizing Guide

Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.

Remember, the length of a screw or bolt is measured from the start of the “mounting

surface” to the end of the screw, so only include the screw head when measuring

countersunk screws.

M3 10.0 in-lbs - 1.0 Nm

M4 23.0 in-lbs - 2.5 Nm

M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm

M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm

M8 - 13.5 ft-lbs 18.0 Nm

M10 - 30.0 ft-lbs 41.0 Nm

M12 - 52.0 ft-lbs 71.0 Nm

in-lbs

ft-lbs NmBolt Size

0in 1 2 3

What’s In The Box?

DENALIELECTRONICS.COM

LAH.23.10200

Harley Davidson Pan America

Front T3 Mounting Bracket

Instruction Manual

(a) T3 Mounting Bracket-R......(DNL.T3.018)................................Qty 1

(b) T3 Mounting Bracket-L......(DNL.T3.019)................................Qty 1

(d) M6x20mm DIN 912 Socket Head Screw...................................Qty 2

(e) DIN 9021; Oversized Washer OD 18mm ID 6.4mm H1.6mm......Qty 2

(f) M6 Washer DIN 125 .............................................................Qty 2

(g) M6 Locking Nut...................................................................Qty 2

Kit Contents

Tools Required: 5mm Hex, 2.5mm Hex, 10mm wrench

(a)

(b)

(c)

(f)

(g)

(e)

(d)

1. Installing The Light Mount DENALIELECTRONICS.COM

Driving

Direction

1.1 - Location Prep & Installation

Step One: Remove the side fairings on either side of the radiator guard that cover the

factory turn signals. They're connected to the bike via screws on the back of the

housing.

Step Two: The side fairings have two connected sections, remove the inner screws and

seperate the two plastics to gain access to the factory lights. From here you can

disconnect and remove the factory turn signals.

Step Three: Using the M3x10mm Socket head screws(c) and 2.5mm Hex Wrench

mount the T3 Pods on to the bracket (a,b). While the Side fairing is disassembled you

can route the cables through the same inner track as the factory turn signals.

Step Four: In the same mounting location as the factory turn signal you can now mount

the front T3 Bracket & Pod. Secure the bracket(a,b) in place with the M6x20mm Socket

Head Screw(d) and Oversized Washer(e) on top and the standard M6 Washer(f) and

Locking Nut(g) below.

Step Five: Reassemble the plastic cover to the side fairing and reattach it to the bike.

Autres manuels Denali Accessoires pour motos

Denali

Denali ALG.003 Manuel utilisateur

Denali

Denali T3 Manuel utilisateur

Denali

Denali KLR650 Manuel utilisateur

Denali

Denali MBK.22.10000 Manuel utilisateur

Denali

Denali LAH.23.10100 Manuel utilisateur

Denali

Denali CANsmart Controller GEN II Manuel utilisateur

Denali

Denali LAH.04.10700 Manuel utilisateur

Denali

Denali LAH.11.10700 Manuel utilisateur

Denali

Denali LAH.23.10000 Manuel utilisateur

Denali

Denali LAH.07.11300 Manuel utilisateur

Denali

Denali HMT.07.11001 Manuel utilisateur

Denali

Denali HMT.04.10200 Manuel utilisateur

Denali

Denali HMT.08.10300 Manuel utilisateur

Denali

Denali DialDim DNL.WHS.23900 Manuel utilisateur

Denali

Denali LAH.07.11000 Manuel utilisateur

Denali

Denali DialDim DNL.WHS.22800 Manuel utilisateur

Denali

Denali DNL.WHS.12700 Manuel utilisateur

Denali

Denali LAH.00.11600 Manuel utilisateur

Denali

Denali MA11729 Manuel utilisateur

Denali

Denali LAH.00.10000.B Manuel utilisateur

Denali

Denali SoundBomb TT-SB.10100.B Manuel utilisateur

Denali

Denali LAH.01.10700 Manuel utilisateur

Denali

Denali DialDim Manuel utilisateur

Denali

Denali D2 Manuel utilisateur

Manuels Accessoires pour motos populaires d'autres marques

SRC

SRC B-TRK502-01-01-SL Manuel utilisateur

3M Speedglas 9100 MP Manuel utilisateur

hepco & becker

hepco & becker 6307520 00 01 Manuel utilisateur

HOMCOM

HOMCOM AA0-077 Manuel utilisateur

hepco & becker

hepco & becker 6307558 00 01 Manuel utilisateur

Wunderkind Custom

Wunderkind Custom 106503-F15 Guide de l'utilisateur

Dräger

Dräger HPS 3500 Manuel utilisateur

M-WAVE

M-WAVE SKI Manuel utilisateur

Kuryakyn

Kuryakyn 6212 Manuel utilisateur

hepco & becker

hepco & becker 6507504 00 01 Manuel utilisateur

Tool it

Tool it PROMAX LCD 9.13G Manuel utilisateur

Custom Dynamics

Custom Dynamics TruWrapz Manuel utilisateur

Roof

Roof RO200 CARBON Manuel utilisateur

Kabuto

Kabuto Japan IBUKI Manuel utilisateur

PUIG

PUIG 5051 Manuel utilisateur

rizoma

rizoma ZTH050 Manuel utilisateur

Joubert

Joubert 10001711 Manuel utilisateur

Sperian

Sperian Optrel p420 Manuel utilisateur